13/30279826 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 15551 - RAILWAY APPLICATIONS - RAILWAY ROLLING STOCK - BUFFERS
Hardcopy , PDF
02-28-2017
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and designation
5 Requirements
6 Housing
7 Crashworthy buffers for tank wagons according to
RID
Annex A (normative) - Maximum space envelope of
buffer
Annex B (normative) - Mechanical characteristics of
buffers - Test methods
Annex C (normative) - Requirements for elastic devices
Annex D (normative) - Testing of static characteristics
of buffers
Annex E (normative) - Dynamic testing
Annex F (normative) - Endurance testing under service
load for elastic device
Annex G (normative) - Endurance testing under buffing
load for life-cycle simulation
Annex H (informative) - Guidelines for buffer head
materials
Annex I (normative) - Calculation of the width of buffer
heads
Annex J (normative) - Crashworthy buffers for tank wagons
according to RID
Annex K (normative) - Maximum space envelope of
crashworthy buffers
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
EU Directive 2008/57/EC of the European
Parliament and of the Council of 17 June 2008
on the interoperability of the rail system within
the Community (Recast)
Bibliography
BS EN 15551
| Committee |
RAE/3/-/7
|
| DocumentType |
Draft
|
| Pages |
76
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 15551 : DRAFT 2013 | Identical |
| EN 10293:2015 | Steel castings - Steel castings for general engineering uses |
| UIC 527-1 : 3ED 2005 | COACHES, VANS AND WAGONS - DIMENSIONS OF BUFFER HEADS - TRACK LAYOUT ON S-CURVES |
| ISO 815-2:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| PN 88/H-83160 : 1988 | ABRASIVE WEAR RESISTANT CAST STEEL - GRADES |
| UIC 827-1 : 2ED 1990 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF ELASTOMER COMPONENTS FOR BUFFERS |
| UIC 528 : 8ED 2007 | BUFFER GEAR FOR COACHES |
| EN 15085-1:2007+A1:2013 | Railway applications - Welding of railway vehicles and components - Part 1: General |
| PREN 15839 : DRAFT 2012 | RAILWAY APPLICATIONS - TESTING FOR THE ACCEPTANCE OF RUNNING CHARACTERISTICS OF RAILWAY VEHICLES - FREIGHT WAGONS - TESTING OF RUNNING SAFETY UNDER LONGITUDINAL COMPRESSIVE FORCES |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| UIC B36 RP 32 : 1989 | CHARACTERISTICS OF THE BUFFING AND DRAW GEAR OF WAGONS TO ENSURE THE SAFE RUNNING OF LONG VEHICLES IN SMALL RADIUS CURVES |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| UIC 526-3 : 3ED 2008 | WAGONS - BUFFERS WITH A STROKE OF 130 AND 150 MM |
| UIC B36 RP 30 : 1990 | REDUCTION OF ACCELERATION DURING BUFFING IMPACTS |
| EN 15227:2008+A1:2010 | Railway applications - Crashworthiness requirements for railway vehicle bodies |
| EN 1370:2011 | Founding - Examination of surface condition |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| UIC 573 : 7ED 2007 | TECHNICAL CONDITIONS FOR THE CONSTRUCTION OF TANK WAGONS |
| EN 10025-5:2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| NFF 10 102 : 1998 | RAILWAY ROLLING STOCK - BUFFERS FOR FREIGHT ROLLING STOCK - ENVELOPES AND COMPONENT PARTS |
| ISO 9001:2015 | Quality management systems — Requirements |
| UIC 827-2 : 3ED 1981 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF STEEL RINGS FOR BUFFER SPRINGS |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| UIC 571-2 : 6ED 2001 | STANDARD WAGONS - ORDINARY BOGIE WAGONS - CHARACTERISTICS |
| UIC 526-1 : 3ED 2008 | WAGONS - BUFFERS WITH A STROKE OF 105 MM |
| EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN 12663-1:2010+A1:2014 | Railway applications - Structural requirements of railway vehicle bodies - Part 1: Locomotives and passenger rolling stock (and alternative method for freight wagons) |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN 15085-2:2007 | Railway applications - Welding of railway vehicles and components - Part 2: Quality requirements and certification of welding manufacturer |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| EN 12663 : 2000 | RAILWAY APPLICATIONS - STRUCTURAL REQUIREMENTS OF RAILWAY VEHICLE BODIES |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| UIC 535-2 : 4ED 2005 | STANDARDISATION AND POSITIONING ON WAGONS OF STEPS, END PLATFORMS, GANGWAYS, HANDRAILS, TOW HOOKS, AUTOMATIC COUPLER (AC), AUTOMATIC DRAW-ON COUPLING AND BRAKE VALVE CONTROLS ON THE UIC MEMBER RUS AND OSJD MEMBER RUS |
| EN 12663-2:2010 | Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight wagons |
| UIC B36 RP 24 : 1984 | GUIDELINES FOR THE EXECUTION OF IMPACT TESTS WITH WAGONS (WITH SIDE BUFFERS OR WITH AUTOMATIC COUPLER) |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN 15085-4:2007 | Railway applications - Welding of railway vehicles and components - Part 4: Production requirements |
| UIC B12 RP 17 : 1997 | PROGRAMME OF TESTS TO BE CARRIED OUT ON WAGONS WITH STEEL UNDER FRAME AND BODY STRUCTURE (SUITABLE FOR BEING FITTED WITH THE AUTOMATIC BUFFING AND DRAW COUPLER) AND ON THEIR CAST STEEL FRAME BOGIES |
| UIC 840-2 : 3ED 1981 | TECHNICAL SPECIFICATION FOR THE SUPPLY OF STEEL CASTINGS FOR TRACTIVE AND TRAILING STOCK |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.