13/30271701 DC : 0
NA
Status of Standard is Unknown
BS EN 16510-1 - RESIDENTIAL SOLID FUEL BURNING APPLIANCES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of appliances and system boundary
for roomsealed appliances
5 Materials, design and construction
6 Safety requirements
7 Performance requirements
8 Appliance instructions
9 Assessment and verification of constancy of
performance - AVCP
10 Marking
Annex A (normative) - Test methods
Annex B (normative) - Test fuels and recommended
fuels
Annex C (informative) - Installation for roomsealed
appliances
Annex D (informative) - Arrangement for measuring the
leakage rate
Annex E (normative) - Measuring procedure for nitrogen
oxides (NO[x])
Annex F (normative) - Measuring procedure for organic
gaseous carbon (OGC)
Annex G (normative) - Measuring procedure for particulate
matter (PM)
Annex H (informative) - Guideline for the characteristics to
be taken into account in order to decide on
families of appliances
Bibliography
BS EN 16510-1
| Committee |
RHE/28
|
| DocumentType |
Draft
|
| Pages |
141
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| Standards | Relationship |
| PREN 16510-1 : DRAFT 2013 | Identical |
| EN 14989-2:2007 | Chimneys - Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications - Part 2: Flue and air supply ducts for room sealed appliances |
| IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| EN 10120:2017 | Steel sheet and strip for welded gas cylinders |
| EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987) |
| CEN/TS 15883:2009 | Residential solid fuel burning appliances - Emission test methods |
| EN 1856-2:2009 | Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| ISO 1928:2009 | Solid mineral fuels Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value |
| ISO 334:2013 | Solid mineral fuels Determination of total sulfur Eschka method |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| CEN/TS 14793:2005 | Stationary source emission - Intralaboratory validation procedure for an alternative method compared to a reference method |
| EN 14597:2012 | Temperature control devices and temperature limiters for heat generating systems |
| ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
| EN 13063-3:2007 | Chimneys - System chimneys with clay/ceramic flue liners - Part 3: Requirements and test methods for air flue system chimneys |
| EN 303-5:2012 | Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 13526:2001 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon in flue gases from solvent using processes - Continuous flame ionisation detector method |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| ISO 331:1983 | Coal Determination of moisture in the analysis sample Direct gravimetric method |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 13284-1:2017 | Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 12619:2013 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
| EN 15250:2007 | Slow heat release appliances fired by solid fuel - Requirements and test methods |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| ISO 687:2010 | Solid mineral fuels — Coke — Determination of moisture in the general analysis test sample |
| ISO 501:2012 | Hard coal — Determination of the crucible swelling number |
| ISO 10849:1996 | Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems |
| EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
| EN 1856-1:2009 | Chimneys - Requirements for metal chimneys - Part 1: System chimney products |
| EN 14792:2017 | Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence |
| ISO 1171:2010 | Solid mineral fuels — Determination of ash |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 562:2010 | Hard coal and coke — Determination of volatile matter |
| EN 1561:2011 | Founding - Grey cast irons |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.