12/30258755 DC : 0
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 1539 - DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS
Available format(s)
Hardcopy , PDF
Superseded date
10-31-2015
Superseded by
Language(s)
English
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and Definitions
4 Significant hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or
measures
7 Information for use
Annex A (normative) - Basis for air flow calculation
of chamber dryers and continuous flow dryers
Annex B (informative) - Examples of calculation
Annex C (normative) - Concentration measurement
in dryers
Annex D (normative) - Explosion reliefs
Annex E (informative) - Sensors for measurement
of the volume flow
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2006/42/EC
Bibliography
BS EN 1539
| Committee |
MCE/3/8
|
| DocumentType |
Draft
|
| Pages |
65
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 1539 : DRAFT 2012 | Identical |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles |
| EN 746-1:1997+A1:2009 | Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment |
| EN 50104:2010 | Electrical apparatus for the detection and measurement of oxygen - Performance requirements and test methods |
| EN 61000-6-1:2007 | Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 12198-2:2002+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 2: Radiation emission measurement procedure |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| EN ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003) |
| EN 746-2:2010 | Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems |
| EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 12433-1:1999 | Industrial, commercial and garage doors and gates - Terminology - Part 1: Types of doors |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| ISO 10218-1:2011 | Robots and robotic devices Safety requirements for industrial robots Part 1: Robots |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
| EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
| EN 13478:2001+A1:2008 | Safety of machinery - Fire prevention and protection |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN 12635:2002+A1:2008 | Industrial, commercial and garage doors and gates - Installation and use |
| EN 12978:2003+A1:2009 | Industrial, commercial and garage doors and gates - Safety devices for power operated doors and gates - Requirements and test methods |
| IEC 60519-6:2011 | Safety in electroheat installations - Part 6: Specifications for safety in industrial microwave heating equipment |
| ISO 5167-4:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 4: Venturi tubes |
| EN 13237:2012 | Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN 1839:2017 | Determination of the explosion limits and the limiting oxygen concentration(LOC) for flammable gases and vapours |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| EN 12445:2000 | Industrial, commercial and garage doors and gates - Safety in use of power operated doors - Test methods |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| EN 12215:2004+A1:2009 | Coating plants - Spray booths for application of organic liquid coating materials - Safety requirements |
| IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
| EN ISO 5167-4:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes (ISO 5167-4:2003) |
| NFPA 68 : 2013 | EXPLOSION PROTECTION BY DEFLAGRATION VENTING |
| EN 12433-2:1999 | Industrial, commercial and garage doors and gates - Terminology - Part 2: Parts of doors |
| ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN 619:2002+A1:2010 | Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads |
| IEC 60405:2003 | Nuclear instrumentation - Constructional requirements and classification of radiometric gauges |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| EN ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 61000-6-4:2007/A1:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN 13023:2003+A1:2010 | Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment - Accuracy grades 2 and 3 |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| EN ISO 10218-1:2011 | Robots and robotic devices - Safety requirements for industrial robots - Part 1: Robots (ISO 10218-1:2011) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 4618:2014 | Paints and varnishes — Terms and definitions |
| EN 12198-3:2002+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 3: Reduction of radiation by attenuation or screening |
| EN 12198-1:2000+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 1: General principles |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN 60079-29-2:2015 | Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen |
| EN 13355:2004+A1:2009 | Coating plants - Combined booths - Safety requirements |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| IEC 60519-1:2015 | Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements |
| EN 14462:2015 | Surface treatment equipment - Noise test code for surface treatment equipment including its ancillary handling equipment - Accuracy grades 2 and 3 |
| EN 14994:2007 | Gas explosion venting protective systems |
| EN ISO 4618:2014 | Paints and varnishes - Terms and definitions (ISO 4618:2014) |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.