10/30234803 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 61169-1 ED.2 - RADIO FREQUENCY CONNECTORS - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND MEASURING METHODS
Hardcopy , PDF
11-30-2013
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 Scope
2 Normative references
3 Definitions
4 Units, symbols and dimensions
5 Standards ratings and characteristics
6 Classifications into climatic categories
7 IEC type designation
8 Testing
9 Test methods
10 Quality assessment
11 Marking
Annex A (informative) - Simulated sea-water solution
for use with salt mist test (marine
environment 9.4.6.2)
Annex B (informative) - Related documents
BS EN 61169-1 ED.2.
| Committee |
EPL/46
|
| DocumentType |
Draft
|
| Pages |
60
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 60457-1:1974 | Rigid precision coaxial and their associated precision connectors. Part 1: General requirements and measuring methods |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 11012:2009 | Heavy commercial vehicles and buses — Open-loop test methods for the quantification of on-centre handling — Weave test and transition test |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| IEC 60096-2:1961 | Radio-frequency cables - Part 2: Relevant cable specifications |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| IEC 60096-0-1:2012+AMD1:2017 CSV | Radio frequency cables - Part 1- 0: Guide to the design of detail specifications - Coaxial cables |
| IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
| IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| IEC 60068-2-47:2005 | Environmental testing - Part 2-47: Test - Mounting of specimens for vibration, impact and similar dynamic tests |
| IEC 60068-2-3:1969 | Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
| IEC 60068-2-54:2006 | Environmental testing - Part 2-54: Tests - Test Ta: Solderability testing of electronic components by the wetting balance method |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60419:1973 | Guide for the inclusion of lot-by-lot and periodic inspection procedures in specifications for electronic components (or parts) |
| ISO 2015:1976 | Numbering of weeks |
| IEC 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| IEC 60027-2:2005 | Letter symbols to be used in electrical technology - Part 2: Telecommunications and electronics |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| ISO 129:1985 | Technical drawings Dimensioning General principles, definitions, methods of execution and special indications |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.