09/30209389 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 60115-8-1 - FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8-1: BLANK DETAIL SPECIFICATION - FIXED CHIP RESISTORS - ASSESSMENT LEVEL E
Hardcopy , PDF
07-31-2015
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
INTRODUCTION
1 General data
2 Inspection requirements
Annex A (normative) - 0 ohm resistors (Jumper)
Annex B (informative) - Letter symbols and abbreviations
Bibliography
BS EN 60115-8-1
| Committee |
EPL/40X
|
| DocumentType |
Draft
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 61193-2:2007 | Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-58:2015+AMD1:2017 CSV | Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| IECQ 001002-3:2005 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 3: APPROVAL PROCEDURES |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| IEC 61760-1:2006 | Surface mounting technology - Part 1: Standard method for the specification of surface mounting components (SMDs) |
| IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
| IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC TR 60440:1973 | Method of measurement of non-linearity in resistors |
| IEC 60062:2016 | Marking codes for resistors and capacitors |
| IEC 61340-3-1:2006 | Electrostatics - Part 3-1: Methods for simulation of electrostatic effects - Human body model (HBM) electrostatic discharge test waveforms |
| IEC 60063:2015 | Preferred number series for resistors and capacitors |
| IEC 60286-3:2013 | Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60115-8:2009 | Fixed resistors for use in electronic equipment - Part 8: Sectional specification - Fixed surface mount resistors |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60115-1:2008 | Fixed resistors for use in electronic equipment - Part 1: Generic specification |
| IEC 60195:2016 | Method of measurement of current noise generated in fixed resistors |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.