09/30181599 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 62386-210 - DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 210: PARTICULAR REQUIREMENTS FOR CONTROL GEARS - SEQUENCER (DEVICE TYPE 9)
Hardcopy , PDF
07-31-2011
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
3.18 Multi channel device
3.19 Point
3.20 Next Point
3.21 Previous point
3.22 Pointer
4 General description
5 Electrical specification
6 Basic requirements for interface power supplies
7 Transmission protocol structure
8 Timing
9 Method of operation
9.2 Power-On
9.3 Interface-failure
9.7 Multi channel device
9.8 Sequencer operation
9.8.1 Externally driven sequencer mode
9.8.2 Automatic sequencer mode
9.8.2.1 Sequencer programming
9.8.2.2 Sequence programming example
9.8.2.3 Starting the automatic sequencer
9.8.2.3.1 Starting with sequencer
commands
9.8.2.3.2 Starting with pointer
9.8.2.4 Stopping the automatic sequencer
10 Declaration of variables
11 Definition of commands
11.1.1 Direct arc power control command
11.1.2 Indirect arc power control commands
11.2.1 General configuration commands:
11.3.1 Queries related to status information
11.3.2 Queries related to arc power parameter settings
11.3.4 Application extended commands
11.3.4.1 Application extended configuration commands
11.3.4.2 Application extended control commands
11.3.4.3 Application extended query commands
11.4.4 Extended special commands
11.5 Summary of the command set
12 Test procedures
12.4 Test sequence 'Physical address allocation'
12.7 Test sequences 'Application extended commands for
device type 9'
12.7.1 Test sequences 'APPLICATION EXTENDED QUERY
COMMANDS'
12.7.1.1 Test sequence 'QUERY FEATURES'
12.7.2 Test sequences 'Application extended
configuration commands'
12.7.2.1 Test sequence 'Configure POINT N'
12.7.2.2 Test sequence 'Configuration - sent
twice'
12.7.2.3 Test sequence 'Configuration -
time-out'
12.7.2.4 Test sequence 'Configuration -
command in-between 1'
12.7.2.5 Test sequence 'Configuration -
command in-between 2'
12.7.2.6 Test sequence 'COPY TO POINT N'
12.7.2.7 Test sequence 'COPY TO POINT N -
sent twice'
12.7.2.8 Test sequence 'COPY TO POINT N -
time-out'
12.7.2.9 Test sequence 'COPY TO POINT N -
command in-between'
12.7.2.10 Test sequence 'CHANNEL SELECTION'
12.7.2.11 Test sequence 'CHANNEL SELECTION -
sent twice/time-out'
12.7.2.12 Test sequence 'CHANNEL SELECTION -
command in-between'
12.7.2.13 Test sequence 'CONFIGURE CONTROL N'
12.7.2.14 Test sequence 'CONFIGURE CONTROL N -
sent twice/time-out'
12.7.2.15 Test sequence "CONFIGURE CONTROL N -
command in-between"
12.7.3 Test sequences 'ENABLE DEVICE TYPE'
12.7.3.1 Test sequence 'ENABLE DEVICE TYPE:
Application extended commands'
12.7.3.2 Test sequence 'ENABLE DEVICE TYPE:
Application extended configuration
commands 1'
12.7.3.3 Test sequence 'ENABLE DEVICE TYPE:
Application extended configuration
commands 2'
12.7.4 Test sequences 'Application extended control
commands'
12.7.4.1 Subsequence 'Configure sequence'
12.7.4.2 Test sequence 'GO TO POINT N'
12.7.4.3 Test sequence 'GO TO NEXT POINT'
12.7.4.4 Test sequence 'GO TO PREVIOUS POINT'
12.7.4.5 Test sequence 'Automatic sequence'
12.7.4.6 Test sequence 'Automatic sequence -
pointer'
12.7.4.7 Test sequence 'Automatic sequence -
number of runs'
12.7.4.8 Test sequence 'Automatic sequence -
stopped by command'
12.7.4.9 Test sequence 'Sequencer performance'
12.7.4.10 Test sequence 'START AT POINT N -
number of runs'
12.7.5 Test sequences 'Application extended
miscellaneous'
12.7.5.1 Test sequence 'RESET SEQUENCER'
12.7.5.2 Test sequence 'RESET SEQUENCER -
send twice/time-out'
12.7.5.3 Test sequence 'RESET SEQUENCER -
command in-between'
12.7.5.4 Test sequence 'RESET CONTROL N'
12.7.5.5 Test sequence 'FAULTY CHANNEL'
12.7.6 Test sequences 'Standard application extended
commands'
12.7.6.1 Test sequences 'QUERY EXTENDED VERSION
NUMBER'
12.7.6.2 Test sequence 'RESERVED APPLICATION
EXTENDED COMMANDS'
BIBLIOGRAPHY
BS EN 62386-210
| Committee |
CPL/34/3
|
| DocumentType |
Draft
|
| Pages |
64
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 62386-102:2014 | Digital addressable lighting interface - Part 102: General requirements - Control gear |
| CISPR 15:2013+AMD1:2015 CSV | Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment |
| IEC 60669-2-1:2002+AMD1:2008+AMD2:2015 CSV | Switches for household and similar fixed electrical installations -Part 2-1: Particular requirements - Electronic switches |
| IEC 60929:2011+AMD1:2015 CSV | AC and/or DC-supplied electronic control gear for tubularfluorescent lamps - Performance requirements |
| IEC 60925:1989+AMD1:1996+AMD2:2001 CSV | DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements |
| IEC 60921:2004+AMD1:2006 CSV | Ballasts for tubular fluorescent lamps - Performance requirements |
| IEC 60598-1:2014+AMD1:2017 CSV | Luminaires - Part 1: General requirements and tests |
| IEC 62386-101:2014 | Digital addressable lighting interface - Part 101: General requirements - System components |
| IEC 60923:2005+AMD1:2006 CSV | Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.