08/30193715 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 62246-1 ED.2 - REED SWITCHES - PART 1: GENERIC SPECIFICATION
Hardcopy , PDF
05-31-2011
English
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 Scope
2 Normative references
3 Terms, definitions
4 Rated values
4.1 General
4.2 Recommended frequency of operation
4.3 Duty factor
4.4 Open-circuit voltage across contacts
4.5 Current rating
4.6 Load ratings
4.7 Number of operations
4.8 Climatic category
4.9 Preferred environmental severities
4.10 Rated operational voltage; U[e]
4.11 Rated switching current; I[e]
4.12 Rated insulation voltage
4.13 Rated impulse voltage
4.14 Utilization categories
4.15 Contact reliability
4.16 Limiting continuous current; Ith
5 Marking
6 Quality assessment procedures
6.1 General
6.2 Self-certification
6.3 Two-party certification
6.4 Third-party certification
6.5 IECEE Scheme:
6.6 IECQ System:
6.7 Qualification approval procedures
6.8 Quality conformance inspection requirements
7 Test and measurement procedures
7.1 General
7.2 Alternative procedures
7.3 Standard conditions for testing
7.4 Visual inspection and check of dimensions
7.5 Functional tests
7.6 Remanence test
7.7 Contact circuit resistance
7.8 Dielectric test
7.9 Insulation resistance
7.10 Operate, release, transfer or bridging,
and bounce times
7.11 Contact sticking
7.12 Robustness of terminals
7.13 Soldering (solderability and resistance
to soldering heat)
7.14 Climatic sequence
7.15 Damp heat, steady state
7.16 Rapid change of temperature
7.17 Salt mist
7.18 Bump
7.19 Vibration
7.20 Shock
7.21 Acceleration test - Functional test only
7.22 Sealing
7.23 Electrical endurance
7.24 Mechanical endurance
7.25 Maximum cycling frequency
7.26 Voltage surge test
7.27 Rated impulse voltage
7.28 Rated making and breaking capacities
7.29 Rated conditional short-circuit current
7.30 Contact reliability test
7.31 Temperature rise
7.32 Making current capacity test
7.33 Breaking current capacity test
Annex A (normative) - Standard test coils for reed switches
Annex B (normative) - Test systems
Annex C (informative) - Electrical endurance test circuit
Annex D (informative) - Rated conditional short-circuit
current test circuit
Annex E (informative) - Electrical ratings based on
utilization categories
Annex F (informative) - Example of test arrangement for
contact reliability test
Annex G (informative) - Making current capacity test sequence
Annex H (informative) - Breaking current capacity test
sequence
Bibliography
BS EN 62246-1 ED.2
| Committee |
EPL/94
|
| DocumentType |
Draft
|
| Pages |
79
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO/IEC 17050-1:2004 | Conformity assessment Supplier's declaration of conformity Part 1: General requirements |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
| ISO/IEC Guide 60:2004 | Conformity assessment Code of good practice |
| IECQ 01:2014 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ SYSTEM) - BASIC RULES |
| IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
| IEC 61810-2:2017 | Electromechanical elementary relays - Part 2: Reliability |
| IEC 60068-2-3:1969 | Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60317-1:2010 | Specifications for particular types of winding wires - Part 1: Polyvinyl acetal enamelled round copper wire, class 105 |
| ISO 9001:2015 | Quality management systems — Requirements |
| IECQ 001002-1:1998 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 1: ADMINISTRATION |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.