S.R. CEN TR 13233:2007
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ADVANCED TECHNICAL CERAMICS - NOTATIONS AND SYMBOLS
Available format(s)
Hardcopy , PDF
Superseded date
14-08-2021
Superseded by
Language(s)
English
Published date
01-01-2007
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Symbols, units and notations
3.1 General symbols
3.2 Symbols and notations specific to ceramic
matrix composites
3.3 Symbols, definitions and units
Bibliography
Specifies the symbols to be used to represent physical, mechanical and thermal characteristics, as determined by methods described in relevant CEN publications, for advanced technical ceramics, including ceramic matrix composites.
| DevelopmentNote |
Supersedes I.S. ENV 13233. (05/2007)
|
| DocumentType |
Standard
|
| Pages |
25
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| CEN/TR 13233 : 2007 COR 2007 | Identical |
| EN 1389:2003 | Advanced technical ceramics - Ceramic composites - Physical properties - Determination of density and apparent porosity |
| EN 12923-1:2006 | Advanced technical ceramics - Monolithic ceramics - Part 1: General practice for undertaking corrosion tests |
| CEN/TS 1159-4:2004 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 4: Determination of thermal conductivity |
| EN 1007-1:2002 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 1: Determination of size content |
| EN 1007-2:2002 | Advanced technical ceramics - Ceramics composites - Methods of test for reinforcement - Part 2: Determination of linear density |
| EN 843-2:2006 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 2: Determination of Young's modulus, shear modulus and Poisson's ratio |
| EN 12290:2005 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of compression properties |
| ISO 80000-4:2006 | Quantities and units Part 4: Mechanics |
| EN 1007-3:2002 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 3: Determination of filament diameter and cross-section area |
| EN 843-1:2006 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 1: Determination of flexural strength |
| EN 821-3:2005 | Advanced technical ceramics - Monolithic ceramics. Thermo-physical properties - Part 3: Determination of specific heat capacity |
| EN 820-1:2002 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermonechanical properties - Part 1: Determination of flexural strength at elevated temperatures |
| EN 12789:2002 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under air at atmospheric pressure - Determination of flexural strength |
| CEN/TS 1071-10:2004 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 10: Determination of coating thickness by cross sectioning |
| EN 12788:2005 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of flexural strength |
| EN 623-4:2004 | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 4: Determination of surface roughness |
| EN 13234:2006 | Advanced technical ceramics - Mechanical properties of ceramic composites at ambient temperature - Evaluation of the resistance to crack propagation by notch sensitivity testing |
| EN 821-1:1995 | Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Part 1: Determination of thermal expansion |
| EN ISO 18756:2005 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of fracture toughness of monolithic ceramics at room temperature by the surface crack in flexure (SCF) method (ISO 18756:2003) |
| ISO 18753:2017 | Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of absolute density of ceramic powders by pycnometer |
| EN 1159-1:2003 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1: Determination of thermal expansion |
| EN 843-5:2006 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 5: Statistical analysis |
| EN 658-1:1998 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 1: Determination of tensile properties |
| ENV 1006 : DRAFT 2003 | ADVANCED TECHNICAL CERAMICS - MONOLITHIC CERAMICS - GUIDANCE ON THE SELECTION OF TEST PIECES FOR THE EVALUATION OF PROPERTIES |
| CEN/TS 1071-11:2005 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 11: Determination of internal stress by the Stoney formula |
| EN 843-3:2005 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 3: Determination of subcritical crack growth parameters from constant stressing rate flexural strength tests |
| CEN/TS 820-5:2004 | Advanced technical ceramics - Methods of testing monolithic ceramics. Thermomechanical properties - Part 5: Determination of elastic moduli at elevated temperatures |
| EN 623-1:2006 | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 1: Determination of the presence of defects by dye penetration |
| EN 820-2:2003 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermo-mechanical properties - Part 2: Determination of self-loaded deformation |
| EN 12289:2005 | Advanced technical ceramics - Mechanical properties of ceramic composites at ambient temperature - Determination of in-plane shear properties |
| CEN/TS 1071-8:2004 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 8: Rockwell indentation test for evaluation of adhesion |
| ENV 1071-6 : DRAFT 2002 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - DETERMINATION OF THE ABRASION RESISTANCE OF COATINGS BY A MICRO-ABRASION WEAR TEST |
| EN 725-11:2006 | Advanced technical ceramics - Methods of test for ceramic powders - Part 11: Determination of densification on natural sintering |
| EN 1892:2005 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of tensile properties |
| EN 725-1:2007 | Advanced technical ceramics - Methods of test for ceramic powders - Part 1: Determination of impurities in alumina |
| ISO 80000-3:2006 | Quantities and units Part 3: Space and time |
| EN 725-8:2006 | Advanced technical ceramics - Methods of test for ceramic powders - Part 8: Determination of tapped bulk density |
| EN ISO 15732:2005 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method (ISO 15732:2003) |
| EN 725-9:2006 | Advanced technical ceramics - Methods of test for ceramic powders - Part 9: Determination of un-tapped bulk density |
| EN 1071-1:2003 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 1: Determination of coating thickness by contact probe filometer |
| EN 623-2:1993 | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 2: Determination of density and porosity |
| EN 658-2:2002 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 2: Determination of compression properties |
| EN 821-2:1997 | Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Part 2: Determination of thermal diffusivity by the laser flash (or heat pulse) method |
| EN 1071-4:2006 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 4: Determination of chemical composition by electron probe microanalysis (EPMA) |
| EN 1893:2005 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of tensile properties |
| EN 658-5:2002 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 5: Determination of interlaminar shear strength by short span bend test (three points) |
| CEN/TS 14425-1:2003 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 1:Guide to test method selection |
| ISO 18756:2003 | Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of fracture toughness of monolithic ceramics at room temperature by the surface crack in flexure (SCF) method |
| CEN/TS 14425-5 : 2004 | ADVANCED TECHNICAL CERAMICS - TEST METHODS FOR DETERMINATION OF FRACTURE TOUGHNESS OF MONOLITIC CERAMICS - PART 5: SINGLE-EDGE VEE-NOTCH BEAM (SEVNB) METHOD |
| EN 843-4:2005 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 4: Vickers, Knoop and Rockwell superficial hardness |
| EN 623-3:2001 | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 3: Determination of grain size and size distribution (characterized by the Linear Intercept Method) |
| EN ISO 18757:2005 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of specific surface area of ceramic powders by gas adsorption using the BET method (ISO 18757:2003) |
| ENV 14226:2002 | Advanced technical ceramics - Test methods for ceramic powders - Determination of calcium, magnesium, iron and aluminium in silicon nitride by using flame atomic absorption spectroscopy (FAAS) or inductively coupled plasma atomic emission spectroscopy (ICP-AES) |
| EN 1159-2:2003 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 2: Determination of thermal diffusivity |
| ENV 1007-6 : DRAFT 2002 | ADVANCED TECHNICAL CERAMICS - CERAMIC COMPOSITES - METHODS OF TEST FOR REINFORCEMENTS - DETERMINATION OF TENSILE PROPERTIES OF FILAMENT AT HIGH TEMPERATURE |
| ENV 658-6 : DRAFT 1993 | ADVANCED TECHNICAL CERAMICS - MECHANICAL PROPERTIES OF CERAMIC COMPOSITES AT ROOM TEMPERATURE - DETERMINATION OF SHEAR STRENGTH BY DOUBLE PUNCH SHEARING |
| ISO 18757:2003 | Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of specific surface area of ceramic powders by gas adsorption using the BET method |
| ENV 14312:2002 | Advanced technical ceramics - Ceramic powders - Determination of flowability behaviour of ceramic granules |
| ENV 14186 : DRAFT 2002 | ADVANCED TECHNICAL CERAMICS - CERAMIC COMPOSITES - MECHANICAL PROPERTIES AT ROOM TEMPERATURE, DETERMINATION OF ELASTIC PROPERTIES BY AN ULTRASONIC TECHNIQUE |
| CEN/TS 1071-7 : 2003 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 7: DETERMINATION OF HARDNESS AND YOUNG'S MODULUS BY INSTRUMENTED INDENTATION TESTING |
| EN 725-7 : 1995 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC POWDERS - PART 7: DETERMINATION OF THE ABSOLUTE DENSITY |
| ENV 14232 : DRAFT 2003 | ADVANCED TECHNICAL CERAMICS - TERMS, DEFINITIONS AND ABBREVIATIONS |
| EN 725-10:2007 | Advanced technical ceramics - Methods of test for ceramic powders - Part 10: Determination of compaction properties |
| EN 820-3:2004 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 3: Determination of resistance to thermal shock by water quenching |
| EN 725-12:2001 | Advanced technical ceramics - Methods of test for ceramic powders - Part 12: Chemical analysis of zirconia |
| EN 725-6 : 1996 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC POWDERS - PART 6: DETERMINATION OF THE SPECIFIC SURFACE AREA |
| EN 1007-4:2004 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature |
| CEN/TS 843-6:2004 | Advanced technical ceramics - Monolithic ceramics. Mechanical properties at room temperature - Part 6: Guidance for fractographic investigation |
| EN 1007-5:2010 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 5: Determination of distribution of tensile strength and of tensile strain to failure of filaments within a multifilament tow at ambient temperature |
| EN 1071-2:2002 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 2: Determination of coating thickness by the crater grinding method |
| ENV 12212 : DRAFT 1995 | ADVANCED TECHNICAL CERAMICS - UNIFIED METHOD FOR CLASSIFICATION |
| ENV 1071-5 : DRAFT 1995 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 5: DETERMINATION OF POROSITY |
| EN 1071-3:2005 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 3: Determination of adhesion and other mechanical failure modes by a scratch test |
| EN ISO 18753:2017 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of absolute density of ceramic powders by pycnometer (ISO 18753:2017) |
| EN 1894:2005 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of shear strength by compression loading of notched specimens |
| EN 725-3:2007 | Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas |
| EN 12291:2003 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of compression properties |
| ENV 12923-2:2001 | Advanced technical ceramics - Monolithic ceramics - Part 2: Oxidation test |
| ENV 725-2 : 1994 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC POWDERS - DETERMINATION OF IMPURITIES IN BARIUM TITANATE |
| EN 658-4:2003 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 4: Determination of interlaminar shear strength by compression loading of notched test specimens |
| ISO 15732:2003 | Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for fracture toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method |
| EN 725-4:2006 | Advanced technical ceramics - Methods of test for ceramic powders - Part 4: Determination of oxygen content in aluminium nitride by XRF analysis |
| ENV 623-5 : DRAFT 2002 | ADVANCED TECHNICAL CERAMICS - MONOLITHIC CERAMICS - GENERAL AND TEXTURAL PROPERTIES - PART 5: DETERMINATION OF PHASE VOLUME FRACTION BY EVALUATION OF MICROGRAPHS |
| ENV 14273:2002 | Advanced technical ceramics - Ceramic powders - Determination of crystalline phases in zirconia |
| ENV 820-4 : DRAFT 2001 | ADVANCED TECHNICAL CERAMICS - MONOLITHIC CERAMICS - THERMOMECHANICAL PROPERTIES - PART 4: DETERMINATION OF FLEXURAL CREEP DEFORMATION AT ELEVATED TEMPERATURES |
| EN 658-3:2002 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 3: Determination of flexural strength |
| EN 13235:2006 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of creep behaviour |
| CEN/TS 1071-9:2004 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 9: Determination of fracture strain |
| CEN/TS 14425-3 : 2003 | ADVANCED TECHNICAL CERAMICS - TEST METHODS FOR DETERMINATION OF FRACTURE TOUGHNESS OF MONOLITHIC CERAMICS - PART 3: CHEVRON NOTCHED BEAM (CNB) METHOD |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.