PREN 13618 : DRAFT 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FLEXIBLE HOSE ASSEMBLIES IN DRINKING WATER INSTALLATIONS - FUNCTIONAL REQUIREMENTS AND TEST METHODS
01-09-2011
12-01-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
4.1 Materials
4.1.1 General
4.1.2 Chemical and hygienic requirements
4.1.3 Hoses
4.1.4 Fittings and sleeves
4.1.5 Braiding
4.1.6 Seals
4.2 Functional requirements
4.2.1 General
4.2.2 Fittings
4.2.3 Hose assemblies
5 Designation
6 Marking
Annex A (normative) - Tests on fittings
A.1 Dimensions and thread control
A.2 Mercury nitrate test or ammonium test
A.3 Tightening test
A.3.1 Test samples
A.3.2 Procedure
A.4 Bending test
A.4.1 Test samples
A.4.2 Procedure
A.5 Endurance of the seat of female fittings
A.5.1 Test samples
A.5.2 Procedure
Annex B (normative) - Hose assembly test
B.1 Flow rate test
B.1.1 Test samples
B.1.2 Procedure
B.2 Ageing treatment by hot storage
B.2.1 Test samples
B.2.2 Procedure
B.3 Tensile test
B.3.1 Test samples
B.3.2 Procedure
B.4 Hydrostatic pressure test
B.4.1 Test samples
B.4.2 Procedure
B.5 Hydraulic performance and durability test
B.5.1 Test samples
B.5.2 Test conditions
B.5.3 Procedure
B.6 Test of resistance to pressure jumps
B.6.1 Test samples
B.6.2 Test conditions
B.6.3 Procedure
B.7 Temperature cycling test
B.7.1 Test samples
B.7.2 Procedure
B.8 Corrosion resistance test
B.8.1 Test samples
B.8.2 Procedure
B.9 Bending test
B.9.1 Test samples
B.9.2 Procedure
B.10 Test of resistance to frost
B.10.1 Test samples
B.10.2 Procedure
Describes the requirements and test methods for materials, dimensions and function for flexible hose assemblies designed for use with drinking water with a maximum static pressure of 1 MPa and maximum operating temperature 70 degree C.
| Committee |
TC 164
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 09/30198696 DC : 0 | Identical |
| 99/104927 DC : DRAFT JUN 1999 | Identical |
| 05/30132908 DC : DRAFT APR 2005 | EN 15200 - SANITARY APPLIANCES - MULTIFUNCTION SHOWER CABINETS |
| 04/30126825 DC : DRAFT DEC 2004 | EN 15091 - SANITARY TAPWARE - ELECTRONIC OPENING AND CLOSING SANITARY TAPWARE |
| 10/30215042 DC : 0 | BS EN 997 - WC PANS AND WC SUITES WITH INTEGRAL TRAP |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| EN ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017) |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| EN 12540 : 2000 | CORROSION PROTECTION OF METALS - ELECTRODEPOSITED COATINGS OF NICKEL, NICKEL PLUS CHROMIUM, COPPER PLUS NICKEL AND COPPER PLUS NICKEL PLUS CHROMIUM |
| ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes |
| EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 22391-2:2009 | Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| ISO 877:1994 | Plastics Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors |
| PREN 1254-6 : DRAFT 2011 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS |
| ISO 196:1978 | Wrought copper and copper alloys — Detection of residual stress — Mercury(I) nitrate test |
| EN ISO 877:1996 | Plastics - Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors (ISO 877:1994) |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| EN 248:2002 | Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.