I.S. EN 12261:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
GAS METERS - TURBINE GAS METERS
Hardcopy , PDF
24-04-2018
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Meter classification
5 Metrological performance requirements
6 Design and material requirements
7 Meter output
8 Marking
9 Documentation
Annex A (normative) - Test facility specifications
Annex B (normative) - Perturbation testing
Annex C (informative) - Recommendations for use
Annex D (normative) - Individual factory testing
Annex E (normative) - Metrological requirements
and tests for each meter prior to dispatch
(Individual meter testing)
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2014/32/EU Measuring
Instruments Directive aimed to be covered
Bibliography
Defines the measuring conditions, requirements and tests for the construction, performance and safety of class 1,0 axial and radial turbine gas meters with mechanical indicating devices, herein after referred to as a meter(s), having in-line pipe connections for gas flow measurement.
| DocumentType |
Standard
|
| Pages |
65
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| Standards | Relationship |
| UNI EN 12261 : 2006 | Identical |
| ONORM EN 12261 : 2007 | Identical |
| DIN EN 12261:2007-07 | Identical |
| SN EN 12261 : 2002 AMD 1 2006 | Identical |
| UNE-EN 12261:2003 | Identical |
| NF EN 12261 : 2002 AMD 1 2006 | Identical |
| NBN EN 12261 : 2002 AMD 1 2006 | Identical |
| BS EN 12261:2002 | Identical |
| NEN EN 12261 : 2018 | Identical |
| NS EN 12261 : 2018 | Identical |
| EN 12261:2018 | Identical |
| EN 12405-1:2005+A2:2010 | Gas meters - Conversion devices - Part 1: Volume conversion |
| OIML D 11 : 2013 | GENERAL REQUIREMENTS FOR MEASURING INSTRUMENTS - ENVIRONMENTAL CONDITIONS |
| ISO 5168:2005 | Measurement of fluid flow — Procedures for the evaluation of uncertainties |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| EN 60947-5-6:2000 | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| EN 334:2005+A1:2009 | Gas pressure regulators for inlet pressures up to 100 bar |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| EN 1333:2006 | Flanges and their joints - Pipework components - Definition and selection of PN |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| IEC 60947-5-6:1999 | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.