EN 792-6:2000+A1:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners
01-10-2010
10-09-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 General terms and definitions
3.2 Terms and definitions related to assembly power tools for
threaded fasteners
4 List of hazards
5 Safety requirements and measures
5.1 Mechanical safety
5.2 Thermal safety
5.3 Noise
5.4 Vibration
5.5 Materials and substances processed, used or exhausted
5.6 Ergonomics
5.7 Safety related measures and means
6 Information for use
6.1 Marking, signs and written warnings
6.2 Instruction for use
7 Verification
7.1 Noise
7.2 Vibration
7.3 Unintentional start
7.4 Structure of verification
Annex A (informative) Examples of assembly power tools for
threaded fasteners covered by this part
Annex B (informative) Symbols for labels and signs
Annex C (normative) Safety requirements related to the internal
combustion engines
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
The standard EN 792 applies to hand-held non-electric power tools driven by rotary or linear motors, powered by compressed air, hydraulic fluid and intended to be used by one operator and supported by:the operator's hand or handsa suspension, e.g. a balancer.This part, EN 792-6, applies to hand-held, non-electric, power tools for tightening or installing of threaded fasteners. This part lists the significant hazards caused by such power tools and specifies safety requirements valid for different aspects of safety during their foreseeable lifetime.Power tools covered by this part of the standard:-air-hydraulic impulse wrenches,-impact wrenches,-fastener installation tools,-nut runners,-open-ended spanners,-ratchet wrenches,-screwdrivers.Special requirements and modifications on a hand-held power tool for the purpose of mounting it in a fixture are not covered by this part.NOTEAt the date of publication no assembly power tools for threaded fasteners driven by internal combustion engines are known.
| Committee |
CEN/TC 255
|
| DevelopmentNote |
2000 Edition Re-Issued in September 2008 & incorporates AMD 1 2008. (10/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 792-6 : 2000 + A1 2008 | Identical |
| PN EN 792-6 : 2004 + A1 2008 | Identical |
| I.S. EN 792-6:2000 | Identical |
| SN EN 792-6 : 2000 + A1 2008 | Identical |
| NF EN 792-6 : 2000 + A1 2008 | Identical |
| DIN EN 792-6:2009-12 | Identical |
| NBN EN 792-6 : 2000 + A1 2009 | Identical |
| UNI EN 792-6 : 2008 | Identical |
| NEN EN 792-6 : 2000 + A1 2008 | Identical |
| UNE-EN 792-6:2001 | Identical |
| BS EN 792-6 : 2000 | Identical |
| UNE-EN 792-6:2001+A1:2008 | Identical |
| DIN EN 792-6:2001-02 | Identical |
| ISO/TS 21108:2005 | Hand-held power tools — Impulse wrenches — Dimensions and tolerances of interface to power socket |
| DD ISO/TS 21108:2005 | Hand-held power tools. Impulse wrenches. Dimensions and tolerances of interface to power socket |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 9158:1988 | Road vehicles Nozzle spouts for unleaded gasoline |
| EN ISO 11690-3:1998 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 3: Sound propagation and noise prediction in workrooms (ISO/TR 11690-3:1997) |
| ISO/TR 11690-3:1997 | Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 3: Sound propagation and noise prediction in workrooms |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN ISO 15744:2008 | Hand-held non-electric power tools - Noise measurement code - Engineering method (grade 2) (ISO 15744:2002) |
| EN 50144-1 : 98 COR 2005 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
| ISO 11690-2:1996 | Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 2: Noise control measures |
| EN 626-2:1996+A1:2008 | Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures |
| ISO 2787:1984 | Rotary and percussive pneumatic tools — Performance tests |
| ISO 3857-1:1977 | Compressors, pneumatic tools and machines — Vocabulary — Part 1: General |
| ISO 11690-1:1996 | Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 1: Noise control strategies |
| EN 28662-1:1992 | Hand-held portable power tools - Measurement of vibrations at the handle - Part 1: General (ISO 8662-1:1988) |
| EN ISO 11690-2:1996 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 2: Noise control measures (ISO 11690-2:1996) |
| ISO 9159:1988 | Road vehicles Nozzle spouts for leaded gasoline and diesel fuel |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| ISO 8662-1:1988 | Hand-held portable power tools Measurement of vibrations at the handle Part 1: General |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| ISO 5391:2003 | Pneumatic tools and machines Vocabulary |
| EN ISO 8662-7 : 1997 | HAND-HELD PORTABLE POWER TOOLS - MEASUREMENT OF VIBRATIONS AT THE HANDLE - PART 7: WRENCHES, SCREWDRIVERS AND NUT RUNNERS WITH IMPACT, IMPULSE OR RATCHET ACTION |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 15744:2002 | Hand-held non-electric power tools Noise measurement code Engineering method (grade 2) |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
| EN ISO 11690-1:1996 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 1: Noise control strategies (ISO 11690-1:1996) |
| ISO 8662-7:1997 | Hand-held portable power tools Measurement of vibrations at the handle Part 7: Wrenches, screwdrivers and nut runners with impact, impulse or ratchet action |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.