• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DIN EN 88:1996-08

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

PRESSURE GOVERNORS FOR GAS APPLIANCES FOR INLET PRESSURES UP TO 200 MBAR

Superseded date

01-04-2008

Superseded by

DIN EN 88-1:2016-06

Published date

12-01-2013

Sorry this product is not available in your region.

1 Allgemeines
  1.1 Zweck und Anwendungsbereich
  1.2 Normative Verweisungen
  1.3 Begriffe
  1.4 Einteilung
  1.5 Messgrössen
2 Bauanforderungen
  2.1 Allgemeine Bauanforderungen
  2.2 Werkstoffe
  2.3 Anschlüsse
  2.4 Abdichten von Durchführungen beweglicher Teile
  2.5 Druckmessstutzen
3 Funktionsanforderungen
  3.1 Allgemeines
  3.2 Ausserbetriebsetzen des Reglers
  3.3 Äussere Dichtheit
  3.4 Torsion und Biegung
  3.5 Beständigkeit
  3.6 Regelverhalten
  3.7 Betriebsgeräusch
  3.8 Langzeitstabilität des Regelverhaltens
  3.9 Schliessdruck
4 Prüfverfahren
  4.1 Allgemeines
  4.2 Ausserbetriebsetzen des Reglers
  4.3 Äussere Dichtheit
  4.4 Torsion und Biegung
  4.5 Beständigkeit
  4.6 Regelverhalten
  4.7 Betriebsgeräusch
  4.8 Langzeitstabilität des Regelverhaltens
  4.9 Schliessdruck
5 Kennzeichnung, Einbau- und Betriebsanleitung
  5.1 Kennzeichnung
  5.2 Anleitungen für Einbau, Betrieb und Wartung
  5.3 Warnhinweis
Anhang A (informativ) Hinweis auf die Überein-stimmung mit
                      den grundlegenden Anfor-derungen der
                      EG-Gasgeräterichtlinie
Anhang B (informativ) Typische Regler und Reglerteile
Anhang C (informativ) Verwendung von Gewindennach ISO 7-1:1982
                      und ISO 228-1: 1982
Anhang D (normativ) Dichtheitsprüfung - volume-trisches
                      Verfahren
Anhang E (normativ) Dichtheitsprüfung - Druck-abfallverfahren
Anhang F (normativ) Umrechnung des Druckabfalls in Leckrate
Anhang G (informativ) Zusammenstellung der Anforderungen und
                      Prüfschritte

This standard is included in DIN Handbook 130. Describes the safety, constructional and performance requirements for pressure governors for use with gas appliances. Gives test procedures for evaluating these and information necessary for the purchaser and user. Applies to pressure governors for gas-burning appliances of connection size up to and including DN 50 and that may be used and tested independently of these appliances. Suitable for fuel gases of the 1st, 2nd and 3rd families. Does not cover: governors connected to mains and governors for gas appliances installed out-of-doors.

DevelopmentNote
Supersedes DIN 3392. (02/2003)
DocumentType
Standard
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

ISO 274:1975 Copper tubes of circular section — Dimensions
DIN 1754-1:1969-08 COPPER TUBES - SEAMLESS DRAWN, DIMENSION RANGES AND COORDINATION OF TOLERANCES
DIN 1786:1980-05 SEAMLESS DRAWN COPPER TUBES FOR PIPING SYSTEMS
DIN EN 60730-1:2017-05 AUTOMATIC ELECTRICAL CONTROLS - PART 1: GENERAL REQUIREMENTS (IEC 60730-1:2013, MODIFIED + COR1:2014)
DIN 13-13:1983-10 ISO METRIC SCREW THREADS - SELECTED SIZES FOR SCREWS, BOLTS AND NUTS FROM 1 TO 52 MM SCREW THREAD DIAMETER AND LIMITS OF SIZES
DIN ISO 228-1:1994-12 PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
DIN 2999-1:1983-07 PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS
ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
DIN 6630:1985-08 PACKAGING SCREW THREADS FOR SCREWING UP PROFILES; DESIGN PROFILES AND SIZES
ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
ISO 301:2006 Zinc alloy ingots intended for castings
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.