DD ENV 13801:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation
Hardcopy , PDF
30-04-2014
English
15-08-2001
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terminology, definitions, symbols and abbreviations
3.1 General terminology
3.2 Definitions
3.3 Symbols
3.4 Abbreviations
4 Design limits of the system
5 Storage, transport and handling
5.1 General
5.2 Transport
5.3 Storage
5.4 Handling on site
6 Installation
6.1 General recommendations for installation
6.2 Recommendations for above-ground installation
6.3 Recommendations for installation in buried
conditions
6.4 Jointing procedure
7 Special precautions
7.1 Concreting of thermoplastics systems within the
building structure
7.2 Foaming of thermoplastics systems
7.3 Prevention of additional stresses in pipe work
8 Jointing to other materials or other constructions
8.1 General
8.2 Solvent-cement joints
8.3 Ring seal joints
8.4 Jointing to non-thermoplastics components
8.5 Adaptors
9 Environmental aspects
10 Fire resistance of pipe work
11 Testing and inspection of installations
11.1 Testing
11.2 General inspection
12 Maintenance and cleaning of installations
12.1 General
12.2 Cleaning and descaling techniques
13 Chemical resistance of thermoplastics materials
Bibliography
Gives the recommended practice for installation of thermoplastics piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with 'B') and of soil and waste discharge systems for both inside buildings and buried in ground within the building structure (marked with 'BD').
| Committee |
PRI/88
|
| DocumentType |
Standard
|
| Pages |
52
|
| PublisherName |
British Standards Institution
|
| RevisionOf | |
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ENV 13801:2000 | Identical |
| ISO 8283-4:1992 | Plastics pipes and fittings — Dimensions of sockets and spigots for discharge systems inside buildings — Part 4: Acrylonitrile/butadiene/styrene (ABS) |
| ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
| EN 12056-2:2000 | Gravity drainage systems inside buildings - Part 2: Sanitary pipework, layout and calculation |
| EN 1566-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system |
| ISO 8283-2:1992 | Plastics pipes and fittings — Dimensions of sockets and spigots for discharge systems inside buildings — Part 2: Polyethylene (PE) |
| EN 12056-1:2000 | Gravity drainage systems inside buildings - Part 1: General and performance requirements |
| EN 1455-1:1999 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system |
| PREN 13476-1 : DRAFT 2015 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLSEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| EN 1519-1:1999 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN 12056-3:2000 | Gravity drainage systems inside buildings - Part 3: Roof drainage, layout and calculation |
| ISO 8283-1:1991 | Plastics pipes and fittings Dimensions of sockets and spigots for discharge systems inside buildings Part 1: Unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly (vinyl chloride) (PVC-C) |
| EN 1565-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system |
| EN 12056-5:2000 | Gravity drainage systems inside buildings - Part 5: Installation and testing, instructions for operation, maintenance and use |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.