BS 1704:1985
Current
The latest, up-to-date edition.
Specification for solid-stem general purpose thermometers
Hardcopy , PDF
English
28-06-1985
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Committees responsible
0 Introduction
1 Scope and field of application
2 Reference
3 Temperature scale
4 Immersion
5 Glass
6 Liquid filling
7 Gas filling
8 Construction
9 Scale lines, immersion line and figuring
10 Accuracy
11 Inscriptions
National appendix A - Testing of British Standard
thermometers
Publication referred to
Specifies requirements for two series of inexpensive liquid-in-glass thermometers of the solid-stem type for use in industry, schools and laboratories when great accuracy is not required.
| Committee |
LBI/1/2
|
| DevelopmentNote |
Supersedes 79/54294 DC. Also numbered as ISO 1770. (06/2005)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
This International Standard specifies requirements for two series of inexpensive “commercial quality?? liquid-in-glass thermometers of the solid-stem type suitable for general purpose use in industry, schools and laboratories when great accuracy of measurement is not required:
- a series designated A to H, in which nominal ranges and maximum overall lengths are specified but which may not be acceptable for testing by a national verification laboratory;
- a series designated J to W of greater accuracy than in a) and with specified ranges and a tolerance on overall length, which may be acceptable for testing by a national verification laboratory.
The temperature range covered by each series is from − 100 °C to + 500 °C.
| BS 4938-1:1982 | Dirt content of milk Method for the determination of dirt content (reference method) |
| BS 1743-6.1:1983 | Methods for analysis of dried milk and dried milk products. Assessment of the heat class of dried milk Heat number method (reference method) |
| BS 5404-1:1976 | Specification for plastics laboratory ware Beakers |
| BS 7317-5:1990 | Methods for analysis of high purity copper cathode Cu-CATH-1 Method for determination of sulphur by hydrogen sulphide evolution and spectrophotometry |
| BS 2782-8:Method 835D:1980 | Methods of testing plastics. Other properties Determination of gelation time of thermosetting resins using a hot plate |
| BS 684-1.8:1976 | Methods of analysis of fats and fatty oils. Physical methods Determination of smoke point |
| BS 4938-2:1982 | Dirt content of milk Method for the determination of visible dirt content (rapid method) |
| BS 696-2:1989 | Determination of fat content of milk and milk products (Gerber method) Methods |
| BS 5226:1991 | Code of practice for equipment and procedures for the cleaning and disinfecting of milking machine installations |
| BS 1881-129:1992 | Testing concrete Method for determination of density of partially compacted semi-dry fresh concrete |
| BS 1041-2.1:1985 | Code for temperature measurement. Expansion thermometers Guide to selection and use of liquid-in-glass thermometers |
| BS 4508-1:1986 | Thermally insulated underground pipelines Specification for steel cased systems with air gap |
| BS 1170:1983 | Recommendations for treatment of water for marine boilers |
| BS 1427:1993 | Guide to field and on-site test methods for the analysis of waters |
| BS 1427:2009 | Guide to on-site test methods for the analysis of waters |
| BS 593:1989 | Specification for laboratory thermometers |
| BS 5273:1975 | Specification. Dense tar surfacing for roads and other paved areas |
| BS 845-2:1987 | Methods for assessing thermal performance of boilers for steam, hot water and high temperature heat transfer fluids. Comprehensive procedure |
| DEFSTAN 02-732/3(2009) : 2009 | THERMOMETERS, LIQUID-IN-GLASS EXPANSION TYPE AND THERMOMETER POCKETS |
| 14/30291598 DC : 0 | BS 8500-2 - CONCRETE - COMPLEMENTARY BRITISH STANDARD TO BS EN 206 - PART 2: SPECIFICATION FOR CONSTITUENT MATERIALS AND CONCRETE |
| BS 5117-1.1:1985 | Testing corrosion inhibiting, engine coolant concentrate (\'antifreeze\'). Methods of test for determination of physical and chemical properties Ancillary procedures |
| DEFSTAN 02-732/2(2000) : 2000 | THERMOMETERS, LIQUID IN GLASS EXPANSION TYPE AND THERMOMETER POCKETS |
| DEFSTAN 68-127/2(2003) : 2003 AMD 1 2003 | ANTIFREEZE: INHIBITED ETHANEDIOL - NATO CODE: S-757 - JOINT SERVICE DESIGNATION: AL-39 |
| BS EN 993-16:1995 | Methods of test for dense shaped refractory products Determination of resistance to sulfuric acid |
| BS 3996:1978 | Specification for colour coding for one-mark and graduated pipettes (including requirements for the service performance of the colour coding enamels) |
| BS AU 141a:1971 | Specification for the performance of diesel engines for road vehicles |
| BS 1728-1:1951 | Methods for the analysis of aluminium and aluminium alloys Determination of copper |
| BS 3947:1976 | Specification for liquid chlorine |
| BS 5962:1980 | Specifications for naphthalene (including test methods) |
| 08/30166603 DC : DRAFT MAR 2008 | BS 1427 - GUIDE TO ON-SITE TEST METHODS FOR THE ANALYSIS OF WATERS |
| BS 3482-3:1991 | Methods of test for desiccants Determination of pH |
| BS 8500-2(2015) : 2015 | CONCRETE - COMPLEMENTARY BRITISH STANDARD TO BS EN 206 - PART 2: SPECIFICATION FOR CONSTITUENT MATERIALS AND CONCRETE |
| BS 8500-2:2002 | Concrete. Complementary British Standard to BS EN 206-1 Specification for constituent materials and concrete |
| BS 8500-2(2006) : 2006 | CONCRETE - COMPLEMENTARY BRITISH STANDARD TO BS EN 206-1 - PART 2: SPECIFICATION FOR CONSTITUENT MATERIALS AND CONCRETE |
| ISO 386:1977 | Liquid-in-glass laboratory thermometers Principles of design, construction and use |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.