AWWA C223 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FABRICATED STEEL AND STAINLESS STEEL-TAPPING SLEEVES
Hardcopy , PDF
01-05-2019
English
01-01-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Specifies fabricated steel and stainless-steel tapping sleeves used to provide outlets and branches on existing pipe with or without interruption of service.
| DocumentType |
Revision
|
| ISBN |
9781583219768
|
| Pages |
28
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| AWWA C604:2017 | INSTALLATION OF BURIED STEEL WATER PIPE - 4 IN. (100 MM) AND LARGER |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| AWWA C207 : 2013 | STEEL PIPE FLANGES FOR WATERWORKS SERVICE, SIZES 4 IN. THROUGH 144 IN. (100 MM THROUGH 3,600 MM) |
| AWWA C550 : 2017 | PROTECTIVE INTERIOR COATINGS FOR VALVES AND HYDRANTS |
| ASME B18.2.4.6M : 2010 | METRIC HEAVY HEX NUTS |
| AWS A5.4 : 92(R2000) | STAINLESS STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING, SPECIFICATION FOR |
| ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| AWS D1.6 : 1999 ERRATA 1999 | STRUCTURAL WELDING CODE - STAINLESS STEEL |
| ANSI/AWWA C200 : 2017 | STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER |
| AWWA C220 : 2017 | STAINLESS-STEEL PIPE, 1/2 IN. (13 MM) AND LARGER |
| ASTM A 744/A744M : 2013 : REDLINE | Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service |
| ANSI/AWWA C213 : 2015 | FUSION-BONDED EPOXY COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
| ASTM A 380 : 2006 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
| AWWA M11 : 2004 | STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION |
| AWWA C228 : 2014 | STAINLESS-STEEL PIPE FLANGE JOINTS FOR WATER SERVICE - SIZES 2 IN. THROUGH 72 IN. (50 MM THROUGH 1,800 MM) |
| ASTM A 351/A351M : 2016-05 | SPECIFICATION FOR CASTINGS, AUSTENITIC, FOR PRESSURE-CONTAINING PARTS |
| NSF 60 : 2016 | DRINKING WATER TREATMENT CHEMICALS - HEALTH EFFECTS |
| AWWA C111/A21.11 : 2017 | RUBBER-GASKET JOINTS FOR DUCTILE-IRON PRESSURE PIPE AND FITTINGS |
| ANSI/AWWA C224 : 2017 | NYLON-11-BASED POLYAMIDE COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
| MSS SP 60 : 2017 | CONNECTING FLANGE JOINT BETWEEN TAPPING SLEEVES AND TAPPING VALVES |
| AWS A5.9 : 93(R1999) | BARE STAINLESS STEEL WELDING ELECTRODES AND RODS, SPECIFICATION FOR |
| AWS D1.1 : 2000 | STRUCTURAL WELDING CODE - STEEL |
| AWWA C218 : 2016 | LIQUID COATINGS FOR ABOVEGROUND STEEL WATER PIPE AND FITTINGS |
| AWWA C210 : 2015 | LIQUID-EPOXY COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.