ASTM F 2882/F2882M : 2017
Current
Current
The latest, up-to-date edition.
Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric)
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-06-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 16
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers the requirements for quenched and tempered alloy steel screws 0.060 through 11/2in. and 1.6 through 48 mm in diameter having a minimum ultimate tensile strength of 170 KSI or 1170 MPa.
1.2The values are stated in inch-pound units for inch fasteners and SI metric units for metric fasteners. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance to the standard.
1.3The following hazard caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 1940 : 2007 : REV A : R2014 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
| ASTM F 1470 : 2012 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 2328 : 2005 : R2011 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs |
| ASTM F 606/F606M : 2019 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM F 1470 : 2002 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2009 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 2282 : 2018 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2282 : 2003 : R2015 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2328M : 2004 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric] |
| ASTM F 2328M : 2006 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric] |
| ASTM F 2328M : 2007 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric] |
| ASTM F 2328M : 2017 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| ASTM F 2282 : 2003 : R2009 : EDT 1 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2328M : 2017 : R2022 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| ASTM F 2328M : 2007 : R2014 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric) |
| ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM F 788/F788M : 2020 : EDT 1 | Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series |
| ASTM F 2282 : 2003 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2328 : 2017 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| ASTM F 1940 : 2001 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
| ASTM F 2328 : 2004 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs |
| ASTM F 2328 : 2014 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| ASTM F 788/F788M : 1997 | Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series |
| ASTM F 1940 : 2007 : REV A | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
| ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM F 2328M : 2005 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric] |
| ASTM F 2328M : 2017 : R2022 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| ASTM F 1470 : 2018 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 2328 : 2005 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs |
| ASTM F 1470 : 2001 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1470 : 2024 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 2282 : 2003 : R2009 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2328 : 2017 : R2022 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
| ASTM E 112 : 2013 | Standard Test Methods for Determining Average Grain Size |
| ASTM F 1940 : 2007 : REV A : R2019 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
| ASTM F 2282 : 2015 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2328M : 2007 : R2013 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric) |
| ASTM F 1940 : 2007 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
| ASTM F 606/F606M : 2021 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM F 2328M : 2014 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| ASTM E 112 : 2024 | Standard Test Methods for Determining Average Grain Size |
| ASTM F 1940 : 2007 : REV A : R2024 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
| ASTM F 2282 : 2023 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 1940 : 1999 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.