ASTM E 1259 : 2018
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Evaluation of Antimicrobials in Liquid Fuels Boiling Below 390 °C
Available format(s)
Hardcopy , PDF
Superseded date
30-06-2023
Superseded by
Language(s)
English
Published date
18-10-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 35
|
| DocumentType |
Standard Practice
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice is designed to evaluate antimicrobial agents for the prevention of microbially influenced deterioration of liquid fuels (as defined by Specification D396, D910, D975, D1655, D2069, D2880, D3699, D4814, D6227, D6751, and D7467), system deterioration, or both.
1.2Knowledge of microbiological techniques is required for these procedures.
1.3It is the responsibility of the investigator to determine whether Good Laboratory Practice (GLP) is required and to follow them where appropriate (40 CFR, 160), or as revised.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7847 : 2022 | Standard Guide for Interlaboratory Studies for Microbiological Test Methods |
| ASTM D 7826 : 2023 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
| ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 7826 : 2019 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
| ASTM D 6469 : 2017 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 7847 : 2017 | Standard Guide for Interlaboratory Studies for Microbiological Test Methods |
| ASTM E 1326 : 1998 | Standard Guide for Evaluating Nonconventional Microbiological Tests Used for Enumerating Bacteria |
| ASTM E 1326 : 2015 | Standard Guide for Evaluating Non-culture Microbiological Tests Used for Enumerating Bacteria |
| ASTM D 3699 : 2019 | Standard Specification for Kerosine |
| ASTM D 6729 : 2001 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Meter Capillary High Resolution Gas Chromatography |
| ASTM D 7463 : 2016 : EDT 1 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 7467 : 2018 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 4814 : 2016 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 6974 : 2009 : R2013 : EDT 2 | Standard Practice for Enumeration of Viable Bacteria and Fungi in Liquid Fuels—Filtration and Culture Procedures |
| ASTM D 396 : 2020 | Standard Specification for Fuel Oils |
| ASTM D 7467 : 2009 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 975 : 2022 | Standard Specification for Diesel Fuel |
| ASTM D 7687 : 2023 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 4814 : 2015 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 1655 : 2021 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 7687 : 2017 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 7463 : 2021 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 396 : 1998 | Standard Specification for Fuel Oils |
| ASTM D 6227 : 1999 | Standard Specification for Grade 82 Unleaded Aviation Gasoline |
| ASTM D 975 : 2019 : REV B | Standard Specification for Diesel Fuel |
| ASTM D 1655 : 2020 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2022 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 7467 : 2008 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 2069 : 1991 : R1998 | Standard Specification for Marine Fuels (Withdrawn 2003) |
| ASTM D 4814 : 2018 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 7467 : 2017 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 1655 : 2022 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 6227 : 2018 | Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component |
| ASTM D 7463 : 2008 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures and Fuel Associated Water |
| ASTM D 975 : 2021 | Standard Specification for Diesel Fuel |
| ASTM D 3699 : 2013 : REV B : EDT 1 | Standard Specification for Kerosine |
| ASTM D 4814 : 2016 : REV : EDT 0 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 1655 : 2015 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 7467 : 2015 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 7978 : 2014 | Standard Test Method for Determination of the Viable Aerobic Microbial Content of Fuels and Associated Water—Thixotropic Gel Culture Method |
| ASTM D 7467 : 2015 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 7978 : 2014 : R2019 | Standard Test Method for Determination of the Viable Aerobic Microbial Content of Fuels and Associated Water—Thixotropic Gel Culture Method |
| ASTM D 1655 : 2016 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 4814 : 2016 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 7463 : 2015 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 1655 : 2017 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 7687 : 2011 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel, Fuel/Water Mixtures, and Fuel-Associated Water with Sample Concentration by Filtration |
| ASTM D 4814 : 2022 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 4814 : 2021 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 975 : 2020 : REV C | Standard Specification for Diesel Fuel |
| ASTM D 4814 : 2021 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 2880 : 2018 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6751 : 2015 : REV B | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 1655 : 2015 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 6227 : 2017 | Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component |
| ASTM D 7467 : 2015 : EDT 1 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 7467 : 2015 : REV C | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 2880 : 2023 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4814 : 2016 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 6751 : 2015 : REV C | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 910 : 2001 | Standard Specification for Aviation Gasoline's |
| ASTM D 7687 : 2021 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 1655 : 2015 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 6751 : 2015 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 1655 : 2021 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM E 1259 : 1994 | Standard Test Method for Evaluation of Antimicrobials in Liquid Fuels Boiling Below 390°C |
| ASTM D 7463 : 2018 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 7467 : 2014 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 3699 : 1978 | Standard Specification for Kerosine |
| ASTM D 6751 : 2002 | Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels |
| ASTM D 910 : 2020 : REV A | Standard Specification for Leaded Aviation Gasolines |
| ASTM D 1655 : 2014 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 910 : 2021 | Standard Specification for Leaded Aviation Gasolines |
| ASTM D 1655 : 1985 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2016 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 6751 : 2023 : REV A | Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels |
| ASTM D 6751 : 2020 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 3699 : 1998 | Standard Specification for Kerosine |
| ASTM D 2880 : 2015 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4814 : 2016 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 6733 : 2001 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Meter Capillary High Resolution Gas Chromatography |
| ASTM D 4814 : 1992 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 1655 : 2021 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 4814 : 2015 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 7463 : 2016 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 6974 : 2003 | Standard Practice for Enumeration of Viable Bacteria and Fungi in Liquid Fuels-Filtration and Culture Procedures |
| ASTM D 7467 : 2018 : REV B | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 1655 : 2021 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3699 : 2018 | Standard Specification for Kerosene |
| ASTM D 1655 : 2014 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2016 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 4814 : 2018 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 6751 : 2023 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 396 : 2009 | Standard Specification for Fuel Oils |
| ASTM D 4814 : 2016 : REV D | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 6469 : 1999 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 4814 : 2021 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 7467 : 2015 : REV C : EDT 1 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 7467 : 2015 : REV B | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 5465 : 1993 : R1998 | Standard Practice for Determining Microbial Colony Counts from Waters Analyzed by Plating Methods |
| ASTM D 6751 : 2015 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 1655 : 2018 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 7467 : 2018 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 4814 : 2018 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 2880 : 1978 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4814 : 2021 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 6293 : 1998 | Standard Test Method for Oxygenates and Paraffin, Olefin, Naphthene, Aromatic (O-PONA) Hydrocarbon Types in Low-Olefin Spark Ignition Engine Fuels by Gas Chromatography |
| ASTM D 7464 : 2008 | Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing |
| ASTM D 2880 : 2014 : REV A | Standard Specification for Gas Turbine Fuel Oils |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.