ASTM D 2126 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging
Hardcopy , PDF
16-03-2025
English
01-12-2020
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers procedures for the thermal and humid exposure of rigid cellular plastics. Conditions used shall be agreed upon between the purchaser and the supplier.
Note 1:A list of commonly used exposure conditions is found in Table 1.
1.2The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:This test method is equivalent to ISO 2796 in the sampling and calculation sections. It is not equivalent to ISO 2796 in the procedure section.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1126 : 2024 | Standard Specification for Faced or Unfaced Rigid Cellular Phenolic Thermal Insulation |
| ASTM C 1594 : 2023 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
| ASTM C 1482 : 2024 : EDT 1 | Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation |
| ASTM C 1289 : 2023 : REV A | Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
| ASTM C 1847 : 2021 | Standard Specification for Direct Buried Pre-Insulated and Jacketed Polyurethane Bonded Low Temperature Hot Water Piping Systems |
| ASTM F 3562 : 2024 | Standard Specification for Selection and Application of Thermal Insulation Systems on Liquefied Natural Gas (LNG) Type C Tanks |
| ASTM C 726 : 2024 | Standard Specification for Mineral Wool Roof Insulation Board |
| ASTM C 591 : 2022 | Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation |
| ASTM C 1029 : 2025 | Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation |
| ASTM C 1484 : 2010 : R2018 | Standard Specification for Vacuum Insulation Panels |
| ASTM D 7425/D7425M : 2013 : R2019 | Standard Specification for Spray Polyurethane Foam Used for Roofing Applications |
| ASTM C 578 : 2023 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM C 1902 : 2022 : REV A | Standard Specification for Cellular Glass Insulation Used in Building and Roof Applications |
| ASTM C 1696 : 2020 | Standard Guide for Industrial Thermal Insulation Systems |
| ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
| ASTM E 456 : 2002 | Standard Terminology for Relating to Quality and Statistics |
| ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
| ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2022 : EDT 1 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 883 : 2024 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2025 | Standard Terminology Relating to Plastics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.