Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

CSA ISO/IEC 15415:2013

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

INFORMATION TECHNOLOGY - AUTOMATIC IDENTIFICATION AND DATA CAPTURE TECHNIQUES - BAR CODE SYMBOL PRINT QUALITY TEST SPECIFICATION - TWO-DIMENSIONAL SYMBOLS

Available format(s)

Hardcopy , PDF

Superseded date

21-07-2021

Language(s)

English

Published date

01-01-2017

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Quality grading
6 Measurement methodology for two-dimensional
  multi-row bar code symbols
7 Measurement methodology for two-dimensional
  matrix symbols
8 Measurement methodologies for composite
  symbologies
9 Substrate characteristics
Annex A (normative) - Symbology-specific parameters and
        values for symbol grading
Annex B (informative) - Symbol grading flowchart for
        two-dimensional matrix symbols
Annex C (informative) - Interpreting the scan and symbol
        grades
Annex D (informative) - Guidance on selection of grading
        parameters in application specifications
Annex E (informative) - Substrate characteristics
Annex F (informative) - Parameter grade overlay applied
        to two-dimensional symbologies
Bibliography

Specifies: - two methodologies for the measurement of specific attributes of two-dimensional bar code symbols, one of these being applicable to multi-row bar code symbologies and the other to two-dimensional matrix symbologies; - methods for evaluating and grading these measurements and deriving an overall assessment of symbol quality; - information on possible causes of deviation from optimum grades to assist users in taking appropriate corrective action.

DocumentType
Standard
Pages
62
ProductNote
Reconfirmed EN
PublisherName
Canadian Standards Association
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO/IEC 15415:2011 Identical

ISO 3951-1:2013 Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
ISO/IEC 16022:2006 Information technology — Automatic identification and data capture techniques — Data Matrix bar code symbology specification
ISO/IEC 16023:2000 Information technology International symbology specification MaxiCode
ISO/IEC 18004:2015 Information technology — Automatic identification and data capture techniques — QR Code bar code symbology specification
ISO/IEC 15426-2:2015 Information technology — Automatic identification and data capture techniques — Bar code verifier conformance specification — Part 2: Two-dimensional symbols
ISO/IEC TR 19782:2006 Information technology Automatic identification and data capture techniques Effects of gloss and low substrate opacity on reading of bar code symbols
ISO 7724-2:1984 Paints and varnishes Colorimetry Part 2: Colour measurement
ISO/IEC 15416:2016 Automatic identification and data capture techniques — Bar code print quality test specification — Linear symbols
ISO/IEC 24723:2010 Information technology — Automatic identification and data capture techniques — GS1 Composite bar code symbology specification
EN 12323:2005 AIDC technologies - Symbology specifications - Code 16K
ISO/IEC 15426-1:2006 Information technology Automatic identification and data capture techniques Bar code verifier conformance specification Part 1: Linear symbols
ISO/IEC 19762-1:2008 Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary Part 1: General terms relating to AIDC
ISO/IEC 24724:2011 Information technology — Automatic identification and data capture techniques — GS1 DataBar bar code symbology specification
ISO 2859-10:2006 Sampling procedures for inspection by attributes Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes
AIM BC6 : 1995(R2000) UNIFORM SYMBOLOGY SPECIFICATION - CODE 49
ISO/IEC TR 29158:2011 Information technology Automatic identification and data capture techniques Direct Part Mark (DPM) Quality Guideline
ISO 3951-3:2007 Sampling procedures for inspection by variables Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
ISO/IEC 19762-2:2008 Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary Part 2: Optically readable media (ORM)
ISO/IEC 24728:2006 Information technology Automatic identification and data capture techniques MicroPDF417 bar code symbology specification
ISO/IEC 24778:2008 Information technology — Automatic identification and data capture techniques — Aztec Code bar code symbology specification
ISO 3951-5:2006 Sampling procedures for inspection by variables Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
ISO/IEC 15438:2015 Information technology Automatic identification and data capture techniques PDF417 bar code symbology specification
ISO 3951-2:2013 Sampling procedures for inspection by variables — Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more