ASTM D 4951 : 2014 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
English
01-10-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.02, 2015 Defines the quantitative determination of barium, boron, calcium, copper, magnesium, molybdenum, phosphorus, sulfur, and zinc in unused lubricating oils and additive packages.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1This test method covers the quantitative determination of barium, boron, calcium, copper, magnesium, molybdenum, phosphorus, sulfur, and zinc in unused lubricating oils and additive packages.
1.2The precision statements are valid for dilutions in which the mass % sample in solvent is held constant in the range of 1 to 5 mass % oil.
1.3The precision tables define the concentration ranges covered in the interlaboratory study. However, both lower and higher concentrations can be determined by this test method. The low concentration limits are dependent on the sensitivity of the ICP instrument and the dilution factor. The high concentration limits are determined by the product of the maximum concentration defined by the linear calibration curve and the sample dilution factor.
1.4Sulfur can be determined if the instrument can operate at a wavelength of 180 nm.
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-PRF-17331 Revision K:2013 | LUBRICATING OIL, STEAM TURBINE AND GEAR, MODERATE SERVICE |
| MIL PRF 009000 : K | LUBRICATING OIL, SHIPBOARD INTERNAL COMBUSTION ENGINE, HIGH-OUTPUT DIESEL |
| MIL-PRF-46167 Revision D:2005 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, ARCTIC |
| MIL-PRF-9000 Revision L:2014 | Lubricating Oil, Shipboard Internal Combustion Engine, High-Output Diesel |
| API 1509 : 2002 | ENGINE OIL LICENSING AND CERTIFICATION SYSTEM |
| SAE MS 1005 : 2017 | LUBRICANTS, INDUSTRIAL OILS, AND RELATED PRODUCTS TYPE HF FIRE-RESISTANT HYDRAULIC FLUIDS - SPECIFICATION |
| ASTM D 7040 :2004 | Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM D 7578 : 2015-06 | GUIDE FOR CALIBRATION REQUIREMENTS FOR ELEMENTAL ANALYSIS OF PETROLEUM PRODUCTS AND LUBRICANTS |
| ASTM D 7040 : 2004 : R2010 | Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM E 2097 : 2000 : R2014 | Standard Guide for Determining the Impact of Extractables from Non-Metallic Materials on the Safety of Biotechnology Products (Withdrawn 2022) |
| ASTM D 4485 : 2017-03 | SPECIFICATION FOR PERFORMANCE OF ACTIVE API SERVICE CATEGORY ENGINE OILS |
| BS EN ISO 4263-4:2006 | Petroleum and related products. Determination of the ageing behaviour of inhibited oils and fluids. TOST test Procedure for industrial gear oils |
| A-A-52306 Revision A:1995 | LUBRICATING OIL, HEAVY-DUTY DIESEL ENGINE |
| NF ISO 24254 : 2008 | LUBRICANTS, INDUSTRIAL OILS AND RELATED PRODUCTS (CLASS L) - FAMILY E (INTERNAL COMBUSTION ENGINE OILS) - SPECIFICATIONS FOR OILS FOR USE IN FOUR-STROKE CYCLE MOTORCYCLE GASOLINE ENGINES AND ASSOCIATED DRIVE TRAINS (CATEGORIES EMA AND EMB) |
| ASTM E 2097 : 2000 | Standard Guide for Determining the Impact of Extractables from Non-Metallic Materials on the Safety of Biotechnology Products |
| MIL-DTL-32353 Revision A:2012 | HYDRAULIC & LUBRICATING OIL, SYNTHETIC HYDROCARBON BASE |
| SAE MS 1004 : 2017 | LUBRICANTS, INDUSTRIAL OILS, AND RELATED PRODUCTS TYPE H (HYDRAULIC FLUIDS) - SPECIFICATION |
| SAE J 357 : 2016 | PHYSICAL AND CHEMICAL PROPERTIES OF ENGINE OILS |
| ASTM D 7876 : 2013 | Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants |
| BIS IS 13656 : 2014 | INTERNAL COMBUSTION ENGINE CRANKCASE OILS FOR AUTOMOTIVE APPLICATION (DIESEL AND GASOLINE) - SPECIFICATION |
| ASTM D 4857 : 2012 : REDLINE | Standard Test Method for Determination of the Ability of Lubricants to Minimize Ring Sticking and Piston Deposits in Two-Stroke-Cycle Gasoline Engines Other Than Outboards |
| ASTM D 6074 : 2015 : REDLINE | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
| ASTM D 7040 : 2004 : R2015 | Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
| SAE J 2359 : 1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, MILITARY COMBAT/TACTICAL SERVICE |
| SAE J 183 : 2017 | ENGINE OIL PERFORMANCE AND ENGINE SERVICE CLASSIFICATION (OTHER THAN 'ENERGY CONSERVING') |
| 06/30159746 DC : 0 | BS EN 50503 - FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - STANDARD FOR THE INVENTORY CONTROL, MANAGEMENT, DECONTAMINATION AND/OR DISPOSAL OF ELECTRICAL EQUIPMENT AND INSULATING LIQUIDS CONTAINING PCBS |
| MIL-PRF-21260 Revision E:1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATIVE BREAK-IN |
| SAE J 2361 : 1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATION BREAK-IN |
| DIN EN ISO 4263-4:2006-05 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test - Part 4: Procedure for industrial gear oils (ISO 4263-4:2006) |
| ASTM D 8110 : 2017 | Standard Test Method for Elemental Analysis of Distillate Products by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) |
| ASTM D 6443 : 2014 : REDLINE | TEST METHOD FOR DETERMINATION OF CALCIUM, CHLORINE, COPPER, MAGNESIUM, PHOSPHORUS, SULFUR, AND ZINC IN UNUSED LUBRICATING OILS AND ADDITIVES BY WAVELENGTH DISPERSIVE X-RAY FLUORESCENCE SPECTROMETRY (MATHEMATICAL CORRECTION PROCEDURE) |
| ASTM D 7303 : 2017 : REDLINE | Standard Test Method for Determination of Metals in Lubricating Greases by Inductively Coupled Plasma Atomic Emission Spectrometry |
| SAE J 1260 : 2012 | STANDARD OIL FILTER TEST OIL |
| ASTM E 2097 : 2000 : R2006 | Standard Guide for Determining the Impact of Extractables from Non-Metallic Materials on the Safety of Biotechnology Products |
| EN ISO 4263-4:2006 | Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test - Part 4: Procedure for industrial gear oils (ISO 4263-4:2006) |
| BS ISO 24254:2007 | Lubricants, industrial oils and related products (class L). Family E (internal combustion engine oils). Specifications for oils for use in four-stroke cycle motorcycle gasoline engines and associated drivetrains (categories EMA and EMB) |
| API 1525A : 1ED 2012 | BULK ENGINE OIL CHAIN OF CUSTODY AND QUALITY DOCUMENTATION |
| SAE MS 1002 : 2017 | LUBRICANTS, INDUSTRIAL OILS, AND RELATED PRODUCTS TYPE C (GEARS) SPECIFICATION |
| MIL L 2104 : F | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT TACTICAL SERVICE |
| SAE MS 1000 : 2013 | LUBRICANTS, INDUSTRIAL OILS, AND RELATED PRODUCTS - CLASSIFICATION |
| ISO 24254:2007 | Lubricants, industrial oils and related products (class L) Family E (internal combustion engine oils) Specifications for oils for use in four-stroke cycle motorcycle gasoline engines and associated drivetrains (categories EMA and EMB) |
| ISO 4263-4:2006 | Petroleum and related products Determination of the ageing behaviour of inhibited oils and fluids TOST test Part 4: Procedure for industrial gear oils |
| SAE J 311 : 2000 | FLUID FOR PASSENGER CAR TYPE AUTOMATIC TRANSMISSIONS |
| ASTM D 4628 : 2016 : REDLINE | Standard Test Method for Analysis of Barium, Calcium, Magnesium, and Zinc in Unused Lubricating Oils by Atomic Absorption Spectrometry |
| ASTM D 4307 : 2017 : REDLINE | Standard Practice for Preparation of Liquid Blends for Use as Analytical Standards |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.