ISO 9142:2003
Current
Current
The latest, up-to-date edition.
Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English, French
Published date
12-04-2003
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 9142:2003 describes laboratory ageing conditions under which adhesive joints may be exposed to various environmental influences -- climatic or chemical -- for the purpose of assessing the effects of such influences on certain properties.
The ageing conditions are applicable to bonded assemblies and may be used to constitute a set of tests for the evaluation of an adhesive.
The results obtained using the procedures described in this International Standard are not necessarily applicable to the determination of the service life of a bonded assembly because there is no direct relation between the test results and the behaviour of a bonded assembly over a period of time under service conditions. However, for certain specific applications, experience with the procedures may enable a correlation to be established.
| DevelopmentNote |
Supersedes ISO/DIS 9142 (12/2003)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 9142:2004-05 | Identical |
| NBN EN ISO 9142 : 2004 | Identical |
| NEN EN ISO 9142 : 2004 | Identical |
| NS EN ISO 9142 : 1ED 2004 | Identical |
| I.S. EN ISO 9142:2004 | Identical |
| PN EN ISO 9142 : 2005 | Identical |
| SN EN ISO 9142 : 2004 | Identical |
| UNI EN ISO 9142 : 2004 | Identical |
| SS-EN ISO 9142:2004 | Identical |
| BS EN ISO 9142:2003 | Identical |
| UNE-EN ISO 9142:2004 | Identical |
| EN ISO 9142:2003 | Identical |
| EN 29142:1993/AC:1997 | Identical |
| NF EN ISO 9142 : 2004 | Identical |
| BS EN 29142:1993 | Identical |
| NEN ISO 9142 : 96 C1 97 | Identical |
| UNE-EN 29142/AC:2001 | Identical |
| NS ISO 9142 : 1ED 1993 | Identical |
| I.S. EN 29142:1994 | Identical |
| DIN EN 29142:1993-09 | Corresponds |
| ISO 26842-1:2013 | Adhesives Test methods for the evaluation and selection of adhesives for indoor wood products Part 1: Resistance to delamination in non-severe environments |
| PREN 1372 : DRAFT 2014 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - PEEL TEST |
| 10/30229682 DC : 0 | BS ISO 26842-2 - ADHESIVES - TEST METHODS FOR THE EVALUATION AND SELECTION OF ADHESIVES FOR INDOOR WOOD PRODUCTS - PART 2: RESISTANCE TO DELAMINATION IN SEVERE ENVIRONMENTS |
| PREN 14276-2 : DRAFT 2017 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| PREN 1373 : DRAFT 2014 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - SHEAR TEST |
| DIN EN 13415:2010-05 | TEST OF ADHESIVE FOR FLOOR COVERING - DETERMINATION OF THE ELECTRICAL RESISTANCE OF ADHESIVE FILMS AND COMPOSITES |
| UNE-EN 1373:2015 | Adhesives - Test method for adhesives for floor and wall coverings - Shear test |
| UNE-EN 1372:2015 | Adhesives - Test method for adhesives for floor and wall coverings - Peel test |
| BS EN 14444:2005 | Structural adhesives. Qualitative assessment of durability of bonded assemblies. Wedge rupture test |
| BS EN 14258:2004 | Structural adhesives. Mechanical behaviour of bonded joints subjected to short and long terms exposure at specified conditions of temperature |
| EN 13415:2010 | Test of adhesives for floor covering - Determination of the electrical resistance of adhesive films and composites |
| CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products |
| DIN EN 14258:2005-02 | Structural adhesives - Mechanical behaviour of bonded joints subjected to short and long terms exposure at specified conditions of temperature |
| DIN EN ISO 4611:2011-04 | Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist (ISO 4611:2010) |
| 05/30131014 DC : DRAFT MAR 2005 | EN 15190 - STRUCTURAL ADHESIVES - TEST METHODS FOR ASSESSING LONG TERM DURABILITY OF BONDED METALLIC STRUCTURES |
| 10/30229679 DC : 0 | BS ISO 26842-1 - ADHESIVES - TEST METHODS FOR THE EVALUATION AND SELECTION OF ADHESIVES FOR INDOOR WOOD PRODUCTS - PART 1: RESISTANCE TO DELAMINATION IN NON-SEVERE ENVIRONMENTS |
| BS ISO 14615:1997 | Adhesives. Durability of structural adhesive joints. Exposure to humidity and temperature under load |
| BS ISO 26842-1:2013 | Adhesives. Test methods for the evaluation and selection of adhesives for indoor wood products Resistance to delamination in non-severe environments |
| PREN ISO 4611 : DRAFT 2010 | PLASTICS - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| 14/30296759 DC : 0 | BS EN 1903 - ADHESIVES - TEST METHOD FOR ADHESIVES FOR PLASTIC OR RUBBER FLOOR COVERINGS OR WALL COVERINGS - DETERMINATION OF DIMENSIONAL CHANGES AFTER ACCELERATED AGEING |
| BS ISO 17194:2007 | Structural adhesives. A standard database of properties |
| 07/30151497 DC : 0 | ISO 26842 - ADHESIVES - GUIDELINES FOR THE SELECTION OF ADHESIVES FOR INDOOR WOOD PRODUCTS BY DURABILITY TESTING |
| BS ISO 26842-2:2013 | Adhesives. Test methods for the evaluation and selection of adhesives for indoor wood products Resistance to delamination in severe environments |
| 08/30180281 DC : DRAFT JUNE 2008 | BS EN 1966 - STRUCTURAL ADHESIVES - CHARACTERIZATION OF A SURFACE BY MEASURING ADHESION BY MEANS OF THE THREE POINT BENDING METHOD |
| 08/19979365 DC : DRAFT FEB 2008 | BS ISO 15928-3 - HOUSES - DESCRIPTION OF PERFORMANCE - PART 3: STRUCTURAL DURABILITY |
| DD CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) Test methods for characterisation of WPC materials and products |
| ISO 14679:1997 | Adhesives — Measurement of adhesion characteristics by a three-point bending method |
| BS EN ISO 9653:2000 | Adhesives. Test method for shear strength of adhesive bonds |
| DIN EN 15274:2015-06 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| UNE-EN 13415:2010 | Test of adhesives for floor covering - Determination of the electrical resistance of adhesive films and composites |
| BS EN 1967:2002 | Structural adhesives. Evaluation of the effectiveness of surface treatment techniques for aluminium using a wet peel test in association with the floating roller method |
| I.S. EN ISO 4611:2010 | PLASTICS - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| DIN EN 1903:2015-07 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR PLASTIC OR RUBBER FLOOR COVERINGS OR WALL COVERINGS - DETERMINATION OF DIMENSIONAL CHANGES AFTER ACCELERATED AGEING |
| I.S. EN 1966:2009 | STRUCTURAL ADHESIVES - CHARACTERIZATION OF A SURFACE BY MEASURING ADHESION BY MEANS OF THE THREE POINT BENDING METHOD |
| I.S. EN 15274:2015 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| ISO 15107:1998 | Adhesives Determination of cleavage strength of bonded joints |
| 10/30206257 DC : 0 | BS EN ISO 4611 - PLASTICS - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| 14/30300568 DC : 0 | BS EN 15274 - GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| 04/30122412 DC : DRAFT SEP 2004 | ISO 17194 - STRUCTURAL ADHESIVES - STANDARD DATABASE OF PROPERTIES |
| ISO 4578:1997 | Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating-roller method |
| ISO 17194:2007 | Structural adhesives A standard database of properties |
| DIN EN 1372:2015-06 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - PEEL TEST |
| DIN EN 1373:2015-06 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - SHEAR TEST |
| DIN EN 1966:2009-07 | STRUCTURAL ADHESIVES - CHARACTERIZATION OF A SURFACE BY MEASURING ADHESION BY MEANS OF THE THREE POINT BENDING METHOD |
| EN 14493 : 2002 | STRUCTURAL ADHESIVES - DETERMINATION OF DYNAMIC RESISTANCE TO CLEAVAGE OF HIGH STRENGTH ADHESIVE BONDS UNDER IMPACT CONDITIONS - WEDGE IMPACT METHOD |
| UNI EN ISO 4611 : 2011 | PLASTICS - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST |
| EN ISO 4611:2010 | Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist (ISO 4611:2010) |
| UNI EN 13415 : 2010 | TEST OF ADHESIVES FOR FLOOR COVERING - DETERMINATION OF THE ELECTRICAL RESISTANCE OF ADHESIVE FILMS AND COMPOSITES |
| UNI EN 1966 : 2009 | STRUCTURAL ADHESIVES - CHARACTERIZATION OF A SURFACE BY MEASURING ADHESION BY MEANS OF THE THREE POINT BENDING METHOD |
| 14/30296753 DC : 0 | BS EN 1372 - ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - PEEL TEST |
| I.S. EN ISO 9653:2000 | ADHESIVES - TEST METHOD FOR SHEAR IMPACT STRENGTH OF ADHESIVE BONDS |
| ISO 26842-2:2013 | Adhesives Test methods for the evaluation and selection of adhesives for indoor wood products Part 2: Resistance to delamination in severe environments |
| 14/30296750 DC : 0 | BS EN 1373 - ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - SHEAR TEST |
| 07/30167352 DC : DRAFT AUG 2007 | BS EN 13415 - TEST OF ADHESIVES FOR FLOOR COVERING - DETERMINATION OF THE ELECTRICAL RESISTANCE OF ADHESIVE FILMS AND COMPOSITES |
| PREN 15274 : DRAFT 2014 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| ISO 15928-3:2015 | Houses Description of performance Part 3: Structural durability |
| ISO 14676:1997 | Adhesives — Evaluation of the effectiveness of surface treatment techniques for aluminium — Wet-peel test by floating-roller method |
| PREN 1903 : DRAFT 2014 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR PLASTIC OR RUBBER FLOOR COVERINGS OR WALL COVERINGS - DETERMINATION OF DIMENSIONAL CHANGES AFTER ACCELERATED AGEING |
| 17/30351221 DC : 0 | BS EN 14276-2 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 2: PIPING - GENERAL REQUIREMENTS |
| S.R. CEN TS 15534-3:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 3: CHARACTERISATION OF WPC PRODUCTS |
| UNE-EN 1903:2015 | Adhesives - Test method for adhesives for plastic or rubber floor coverings or wall coverings - Determination of dimensional changes after accelerated ageing |
| BS EN 1903:2015 | Adhesives. Test method for adhesives for plastic or rubber floor coverings or wall coverings. Determination of dimensional changes after accelerated ageing |
| BS EN 1373:2015 | Adhesives. Test method for adhesives for floor and wall coverings. Shear test |
| BS EN 14493:2002 | Structural adhesives. Determination of dynamic resistance to cleavage of high strength adhesive bonds under impact conditions. Wedge impact method |
| UNE-EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| I.S. EN 1372:2015 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - PEEL TEST |
| ISO 4611:2010 | Plastics Determination of the effects of exposure to damp heat, water spray and salt mist |
| I.S. EN 13415:2010 | TEST OF ADHESIVES FOR FLOOR COVERING - DETERMINATION OF THE ELECTRICAL RESISTANCE OF ADHESIVE FILMS AND COMPOSITES |
| ISO 9653:1998 | Adhesives Test method for shear impact strength of adhesive bonds |
| BS EN 1372:2015 | Adhesives. Test method for adhesives for floor and wall coverings. Peel test |
| BS EN 1966:2009 | Structural adhesives. Characterization of a surface by measuring adhesion by means of the three point bending method |
| I.S. EN 1373:2015 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR FLOOR AND WALL COVERINGS - SHEAR TEST |
| BS EN 14173:2002 | Structural adhesives. T-peel test for flexible-to-flexible bonded assemblies |
| I.S. EN 1903:2015 | ADHESIVES - TEST METHOD FOR ADHESIVES FOR PLASTIC OR RUBBER FLOOR COVERINGS OR WALL COVERINGS - DETERMINATION OF DIMENSIONAL CHANGES AFTER ACCELERATED AGEING |
| EN 15190:2007 | Structural adhesives - Test methods for assessing long term durability of bonded metallic structures |
| EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| EN 1372:2015 | Adhesives - Test method for adhesives for floor and wall coverings - Peel test |
| EN 1903:2015 | Adhesives - Test method for adhesives for plastic or rubber floor coverings or wall coverings - Determination of dimensional changes after accelerated ageing |
| EN 14173 : 2002 | STRUCTURAL ADHESIVES - T-PEEL TEST FOR FLEXIBLE-TO-FLEXIBLE BONDED ASSEMBLIES |
| EN 14258:2004 | Structural adhesives - Mechanical behaviour of bonded joints subjected to short and long terms exposure at specified conditions of temperature |
| EN 1373:2015 | Adhesives - Test method for adhesives for floor and wall coverings - Shear test |
| EN ISO 9653:2000 | Adhesives - Test method for shear impact strength of adhesive bonds (ISO 9653:1998) |
| EN 1966:2009 | Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method |
| I.S. EN 14493:2002 | STRUCTURAL ADHESIVES - DETERMINATION OF DYNAMIC RESISTANCE TO CLEAVAGE OF HIGH STRENGTH ADHESIVE BONDS UNDER IMPACT CONDITIONS - WEDGE IMPACT METHOD |
| DD CEN/TS 15534-3:2007 | Wood-plastics composites (WPC) Characterisation of WPC products |
| S.R. CEN TS 15534-1:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS |
| BS EN 13415:2002 | Adhesives. Test of adhesives for floor coverings. Determination of the electrical resistance of adhesive films |
| BS EN 15274:2015 | General purpose adhesives for structural assembly. Requirements and test methods |
| BS EN ISO 4611:2010 | Plastics. Determination of the effects of exposure to damp heat, water spray and salt mist |
| BS EN 15190:2007 | Structural adhesives. Test methods for assessing long term durability of bonded metallic structures |
| CEN/TS 15534-3:2007 | Wood-plastics composites (WPC) - Part 3: Characterisation of WPC products |
| DIN EN 15190:2007-10 | Structural adhesives - Test methods for assessing long term durability of bonded metallic structures |
| DIN EN 14444:2006-01 | Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test (ISO 10354:1992 modified) |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| ISO 483:2005 | Plastics — Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value |
| EN ISO 4892-1:2016 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| EN ISO 4892-3:2016 | Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016) |
| ISO 3205:1976 | Preferred test temperatures |
| ISO 4588:1995 | Adhesives Guidelines for the surface preparation of metals |
| ISO 4587:2003 | Adhesives Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| ISO 6238:2001 | Adhesives Wood-to-wood adhesive bonds Determination of shear strength by compressive loading |
| EN ISO 483:2005 | Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value (ISO 483:2005) |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| EN ISO 175:2010 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.