ASTM E 1745 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs
Hardcopy , PDF
05-26-2023
English
05-04-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This specification covers flexible, preformed sheet membrane materials to be used as vapor retarders in contact with soil or granular fill under concrete slabs.
| Committee |
E 06
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers flexible, preformed sheet membrane materials to be used as vapor retarders in contact with soil or granular fill under concrete slabs.
1.1.1This specification does not cover bituminous vapor retarders. See Specification E1993/E1993M for information on bituminous vapor retarders.
1.2The specified tests are conducted on new materials and materials that have been conditioned or exposed to simulate potential service conditions.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2435 : 2005 : R2020 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
| ASTM D 8408/D8408M : 2021 | Standard Guide for Development of Long-Term Monitoring Plans for Vapor Mitigation Systems |
| ASTM F 710 : 2022 | Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring |
| ASTM E 241 : 2020 | Standard Guide for Limiting Water-Induced Damage to Buildings |
| ASTM D 7832/D7832M : 2014 : R2021 | Standard Guide for Performance Attributes of Waterproofing Membranes Applied to Below-Grade Walls / Vertical Surfaces (Enclosing Interior Spaces) |
| ASTM F 1869 : 2022 | Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride |
| ASTM E 2121 : 2021 | Standard Practice for Installing Radon Mitigation Systems in Existing Low-Rise Residential Buildings |
| ASTM F 1869 : 2016 : REV A | Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride |
| ASTM E 2435 : 2005 : R2015 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
| ASTM E 241 : 2009 : R2014 : EDT 1 | Standard Guide for Limiting Water-Induced Damage to Buildings |
| ASTM E 2121 : 2013 | Standard Practice for Installing Radon Mitigation Systems in Existing Low-Rise Residential Buildings |
| ASTM D 7832/D7832M : 2014 | Standard Guide for Performance Attributes of Waterproofing Membranes Applied to Below-Grade Walls / Vertical Surfaces (Enclosing Interior Spaces) |
| ASTM F 710 : 2019 | Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring |
| ASTM E 1643 : 2018 : REV A | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM C 168 : 2019 | Standard Terminology Relating to Thermal Insulation |
| ASTM D 1709 : 2022 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM F 1249 : 2006 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM E 96/E96M : 2022 : REV A : EDT 1 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 1709 : 2004 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM E 96/E96M : 2022 : REV A | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2021 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM F 1249 : 1994 : REV B | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM E 1643 : 2009 | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM E 96/E96M : 2022 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 1709 : 2015 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 2009 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 1998 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM E 1643 : 2011 : R2017 | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM D 1709 : 2001 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM F 1249 : 2006 : R2011 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM E 1643 : 2011 | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM E 96/E96M : 2016 | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM E 1643 : 2018 : REV A | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM D 1709 : 2016 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 2008 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM F 1249 : 1990 : R1995 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 1709 : 2016 : REV A : EDT 1 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM C 168 : 2022 | Standard Terminology Relating to Thermal Insulation |
| ASTM D 828 : 2016 : EDT 1 | Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus |
| ASTM D 1709 : 2003 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM E 1643 : 2018 | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM D 828 : 2022 | Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus |
| ASTM E 1643 : 2010 | Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM E 1643 : 1998 | Standard Practice for Installation of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs |
| ASTM D 1709 : 2015 : REV A | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM F 1249 : 2001 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 1709 : 2016 : REV A | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM F 1249 : 2013 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.