ASTM E 162 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
Hardcopy , PDF
09-16-2021
English
01-18-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1.1This fire-test-response standard describes the measurement of surface flammability of materials.
| Committee |
E 05
|
| DevelopmentNote |
This standard was just updated in our system however it was originally released on 01-2017
|
| DocumentType |
Test Method
|
| Pages |
12
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This fire-test-response standard describes the measurement of surface flammability of materials. It is not intended for use as a basis of ratings for building code purposes (see Appendix X1).
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section .
Note 1:There is no similar or equivalent ISO standard.
| ASTM E 2061 : 2020 | Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles |
| ASTM F 3214 : 2018 | Standard Practice for Characterization of Fire Properties of Materials Specified for Vehicles Associated with Amusement Rides and Devices |
| ASTM F 1870 : 2016 | Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM D 3574 : 2017 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM E 3020 : 2016 : REV A | Standard Practice for Ignition Sources |
| ASTM E 1317 : 2019 | Standard Test Method for Flammability of Surface Finishes |
| ASTM D 4727/D4727M : 2017 | Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes |
| ASTM E 1321 : 2018 | Standard Test Method for Determining Material Ignition and Flame Spread Properties |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM E 176 : 2021 | Standard Terminology of Fire Standards |
| ASTM E 1546 : 2015 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM C 1288 : 1999 : R2004 | Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets |
| ASTM C 1288 : 2014 | Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets |
| ASTM D 3675 : 2005 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 1546 : 2009 : REV A | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM D 3675 : 2009 : REV A | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3675 : 2009 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3675 : 2021 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM C 1186 : 1991 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM D 3675 : 2014 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 176 : 2018 : REV A : EDT 1 | Standard Terminology of Fire Standards |
| ASTM C 1288 : 1999 | Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets |
| ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 1288 : 1999 : R2010 | Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets |
| ASTM C 1288 : 1999 : R2004 : EDT 1 | Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets |
| ASTM E 1546 : 2000 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 3675 : 2001 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using A Radiant Heat Energy Source |
| ASTM D 3675 : 2008 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 176 : 2021 | Standard Terminology of Fire Standards |
| ASTM D 3675 : 2019 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3675 : 2016 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 176 : 2018 : REV A : EDT 2 | Standard Terminology of Fire Standards |
| ASTM C 1186 : 2002 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM E 1546 : 2021 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM D 3675 : 2021 : REV A | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 1546 : 2000 : EDT 1 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM C 1288 : 2017 | Standard Specification for Fiber-Cement Interior Substrate Sheets |
| ASTM D 3675 : 2017 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM C 1186 : 2008 : R2012 | Standard Specification for Flat Fiber-Cement Sheets |
| ASTM C 1186 : 1999 : EDT 1 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM E 1546 : 2009 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM D 3675 : 2011 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3675 : 2012 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3675 : 1998 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using A Radiant Heat Energy Source |
| ASTM E 1546 : 2007 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM C 1186 : 2008 : R2016 | Standard Specification for Flat Fiber-Cement Sheets |
| ASTM C 1186 : 2007 | Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets |
| ASTM C 1186 : 2008 | Standard Specification for Flat Fiber-Cement Sheets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.