ASTM E 11 : 2020
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
Available format(s)
Hardcopy , PDF
Superseded date
06-06-2024
Superseded by
Language(s)
English
Published date
05-06-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 29
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This document specifies the technical requirements for; the woven wire test sieve cloth (sieve cloth) used in test sieves, the construction of test sieves, standard and non-standard test sieve frame sizes, and test procedures used to inspect sieve cloth and the test sieves. This specification applies to test sieves manufactured with sieve cloth having a nominal aperture size ranging from 125 millimetres (mm) down to 20 micrometres (μm).
1.2Additional reference information can be found in Specifications E161, E323, E2016, and in Test Methods C430 and E2427.
1.3The values stated in SI units shall be considered standard for the dimensions of the sieve cloth openings and the wire diameters used in the sieve cloth. The values stated in inch-pound units shall be considered standard with regard to the sieve frames, pans, and covers.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 285 : 2010 : R2020 | Standard Test Methods for Sieve Analysis of Wet-Milled and Dry-Milled Porcelain Enamel |
| ASTM D 244 : 2009 : R2017 | Standard Test Methods and Practices for Emulsified Asphalts |
| ASTM E 726 : 2001 : R2021 | Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides |
| ASTM D 6572 : 2021 | Standard Test Methods for Determining Dispersive Characteristics of Clayey Soils by the Crumb Test |
| ASTM E 1757 : 2019 | Standard Practice for Preparation of Biomass for Compositional Analysis |
| ASTM D 6393/D6393M : 2021 | Standard Test Method for Bulk Solids Characterization by Carr Indices |
| ASTM C 641 : 2017 | Standard Test Method for Iron Staining Materials in Lightweight Concrete Aggregates |
| ASTM D 5581 : 2007 : REV A : R2021 : EDT 1 | Standard Test Method for Resistance to Plastic Flow of Bituminous Mixtures Using Marshall Apparatus (6 in. Diameter Specimen) |
| ASTM A 481 : 2005 : R2020 | Standard Specification for Chromium Metal |
| ASTM C 1176/C1176M : 2020 | Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table |
| ASTM E 276 : 2021 | Standard Test Method for Particle Size or Screen Analysis at 4.75 mm (No. 4) Sieve and Finer for Metal-Bearing Ores and Related Materials |
| ASTM C 492 : 1992 : R2017 : EDT 1 | Standard Test Method for Hydration of Granular Dead-Burned Refractory Dolomite |
| ASTM D 4072 : 1998 : R2018 | Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch |
| ASTM D 3744/D3744M : 2018 | Standard Test Method for Aggregate Durability Index |
| ASTM C 1170/C1170M : 2020 | Standard Test Method for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table |
| ASTM D 4572 : 2021 | Standard Test Method for Rubber Chemicals—Wet Sieve Analysis of Sulfur |
| ASTM D 126 : 1987 : R2019 | Standard Test Methods for Analysis of Yellow, Orange, and Green Pigments Containing Lead Chromate and Chromium Oxide Green |
| ASTM C 1084 : 2019 | Standard Test Method for Portland-Cement Content of Hardened Hydraulic-Cement Concrete |
| ASTM D 4791 : 2019 | Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate |
| ASTM D 3042 : 2017 | Standard Test Method for Insoluble Residue in Carbonate Aggregates |
| ASTM C 781 : 2020 | Standard Practice for Testing Graphite Materials for Gas-Cooled Nuclear Reactor Components |
| ASTM D 293/D293M : 2018 | Standard Test Method for the Sieve Analysis of Coke |
| ASTM F 3091/F3091M : 2014 : R2021 | Standard Specification for Powder Bed Fusion of Plastic Materials |
| ASTM D 4292 : 2017 | Standard Test Method for Determination of Vibrated Bulk Density of Calcined Petroleum Coke |
| ASTM D 1508 : 2012 : R2017 | Standard Test Method for Carbon Black, Pelleted Fines and Attrition |
| ASTM D 2415 : 2020 | Standard Test Method for Ash in Coal Tar and Pitch |
| ASTM D 1556/D1556M : 2015 : EDT 1 | Standard Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method (Withdrawn 2024) |
| ASTM D 2862 : 2016 | Standard Test Method for Particle Size Distribution of Granular Activated Carbon |
| ASTM E 323 : 2011 : R2021 | Standard Specification for Perforated-Plate Sieves for Testing Purposes |
| ASTM D 4373 : 2021 | Standard Test Method for Rapid Determination of Carbonate Content of Soils |
| ASTM D 2067 : 1997 : R2020 | Standard Test Method for Coarse Particles in Printing Ink Dispersions |
| ASTM D 7382 : 2020 | Standard Test Methods for Determination of Maximum Dry Unit Weight of Granular Soils Using a Vibrating Hammer |
| ASTM D 425 : 2017 | Standard Test Method for Centrifuge Moisture Equivalent of Soils (Withdrawn 2024) |
| ASTM D 8 : 2022 | Standard Terminology Relating to Materials for Roads and Pavements |
| ASTM D 4895 : 2018 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
| ASTM C 1260 : 2021 | Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method) |
| ASTM B 851 : 2004 : R2020 | Standard Specification for Automated Controlled Shot Peening of Metallic Articles Prior to Nickel, Autocatalytic Nickel, or Chromium Plating, or as Final Finish |
| ASTM C 183/C183M : 2016 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
| ASTM D 4715 : 1998 : R2017 | Standard Test Method for Coking Value of Tar and Pitch (Alcan) |
| ASTM C 135 : 1996 : R2022 | Standard Test Method for True Specific Gravity of Refractory Materials by Water Immersion |
| ASTM C 831 : 2018 | Standard Test Methods for Residual Carbon, Apparent Residual Carbon, and Apparent Carbon Yield in Coked Carbon-Containing Brick and Shapes |
| ASTM A 504/A504M : 2018 | Standard Specification for Wrought Carbon Steel Wheels |
| ASTM A 100 : 2007 : R2018 | Standard Specification for Ferrosilicon |
| ASTM E 32 : 2021 | Standard Practices for Sampling Ferroalloys and Steel Additives for Determination of Chemical Composition |
| ASTM D 4315 : 2021 | Standard Test Methods for Rubber Compounding Material—Zinc Oxide |
| ASTM C 1152/C1152M : 2020 | Standard Test Method for Acid-Soluble Chloride in Mortar and Concrete |
| ASTM D 2331 : 2008 : R2013 | Standard Practices for Preparation and Preliminary Testing of Water-Formed Deposits |
| ASTM D 2797/D2797M : 2021 : REV A | Standard Practice for Preparing Coal Samples for Microscopical Analysis by Reflected Light |
| ASTM D 7560 : 2016 : EDT 1 | Standard Test Method for Determination of Fiber Length Percentages in Hydraulic Erosion Control Products (HECPs) |
| ASTM A 482/A482M : 2011 : R2021 | Standard Specification for Ferrochrome-Silicon |
| ASTM C 323 : 1956 : R2016 | Standard Test Methods for Chemical Analysis of Ceramic Whiteware Clays (Withdrawn 2024) |
| ASTM E 324 : 2016 | Standard Test Method for Relative Initial and Final Melting Points and the Melting Range of Organic Chemicals |
| ASTM E 102/E102M : 1993 : R2021 | Standard Test Method for Saybolt Furol Viscosity of Bituminous Materials at High Temperatures |
| ASTM D 5821 : 2013 : R2017 | Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate |
| ASTM D 113 : 2017 | Standard Test Method for Ductility of Asphalt Materials |
| ASTM C 403/C403M : 2016 | Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance |
| ASTM C 471M : 2020 : REV A : EDT 1 | Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products (Metric) |
| ASTM C 331/C331M : 2017 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM D 6155 : 2019 | Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures |
| ASTM D 3466 : 2006 : R2018 | Standard Test Method for Ignition Temperature of Granular Activated Carbon |
| ASTM A 483/A483M : 2010 : R2020 | Standard Specification for Silicomanganese |
| ASTM F 1877 : 2016 | Standard Practice for Characterization of Particles |
| ASTM D 5644 : 2018 | Standard Test Method for Rubber Compounding Materials—Determination of Particle Size Distribution of Recycled Vulcanizate Particulate Rubber |
| ASTM C 1797 : 2017 | Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete |
| ASTM F 3213 : 2017 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion |
| ASTM D 4943 : 2018 | Standard Test Method for Shrinkage Factors of Cohesive Soils by the Water Submersion Method |
| ASTM D 3147 : 2021 | Standard Test Method for Testing Stop-Leak Additives for Engine Coolants |
| ASTM D 559/D559M : 2015 | Standard Test Methods for Wetting and Drying Compacted Soil-Cement Mixtures |
| ASTM D 1301 : 1991 : R2020 | Standard Test Methods for Chemical Analysis of White Lead Pigments |
| ASTM A 550 : 2016 : R2021 | Standard Specification for Ferrocolumbium (Ferroniobium) |
| ASTM D 441 : 2007 : R2019 : EDT 1 | Standard Test Method of Tumbler Test for Coal |
| ASTM D 7724 : 2018 : EDT 1 | Standard Test Method for Carbon Black—Non-Dispersible Matter by Mechanical Flushing (NDM) |
| ASTM D 7608 : 2018 : EDT 1 | Standard Test Method for Torsional Ring Shear Test to Measure Drained Fully Softened Shear Strength and Stress Dependent Strength Envelope of Fine-Grained Soils |
| ASTM E 1520 : 1999 : R2015 | Standard Test Method for Particle Counts Per Pound of Granular Carriers and Dry-Applied Granular Formulations |
| ASTM D 1997 : 2020 | Standard Test Method for Laboratory Determination of the Fiber Content of Peat and Organic Soils by Dry Mass |
| ASTM F 1284 : 2009 : R2016 | Standard Test Method for Evaluating Carpet Embedded Dirt Removal Effectiveness of Residential Central Vacuum Cleaning Systems |
| ASTM D 4829 : 2021 | Standard Test Method for Expansion Index of Soils |
| ASTM C 753 : 2016 : REV A : R2021 | Standard Specification for Nuclear-Grade, Sinterable Uranium Dioxide Powder |
| ASTM D 6928 : 2017 | Standard Test Method for Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus |
| ASTM D 297 : 2021 | Standard Test Methods for Rubber Products—Chemical Analysis |
| ASTM C 1436 : 2013 | Standard Specification for Materials for Shotcrete (Withdrawn 2022) |
| ASTM D 4893 : 2020 | Standard Test Method for Determination of Pitch Volatility |
| ASTM D 444 : 1988 : R2020 | Standard Test Methods for Chemical Analysis of Zinc Yellow Pigment (Zinc Chromate Yellow) |
| ASTM D 8038 : 2016 | Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material |
| ASTM D 4513 : 2011 : R2017 | Standard Test Method for Particle Size Distribution of Catalytic Materials by Sieving |
| ASTM D 7486 : 2014 | Standard Test Method for Measurement of Fines and Dust Particles on Plastic Pellets by Wet Analysis |
| ASTM D 7481 : 2018 | Standard Test Methods for Determining Loose and Tapped Bulk Densities of Powders using a Graduated Cylinder |
| ASTM D 7084 : 2018 | Standard Test Method for Determination of Bulk Crush Strength of Catalysts and Catalyst Carriers |
| ASTM F 3302 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion |
| ASTM D 5519 : 2015 | Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials (Withdrawn 2024) |
| ASTM C 702/C702M : 2018 | Standard Practice for Reducing Samples of Aggregate to Testing Size |
| ASTM F 1377 : 2021 | Standard Specification for Cobalt-28Chromium-6Molybdenum Powder for Medical Devices (UNS R30075, UNS R31537, and UNS R31538) |
| ASTM C 279 : 2017 | Standard Specification for Chemical-Resistant Masonry Units |
| ASTM G 65 : 2016 : R2021 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus |
| ASTM D 4944 : 2018 | Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester |
| ASTM C 172/C172M : 2017 | Standard Practice for Sampling Freshly Mixed Concrete |
| ASTM A 635/A635M : 2015 | Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for |
| ASTM C 157/C157M : 2017 | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 117 : 2017 | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
| ASTM D 6084/D6084M : 2021 | Standard Test Method for Elastic Recovery of Asphalt Materials by Ductilometer |
| ASTM D 6935 : 2017 | Standard Test Method for Determining Cement Mixing of Emulsified Asphalt |
| ASTM B 329 : 2020 | Standard Test Method for Apparent Density of Metal Powders and Compounds Using the Scott Volumeter |
| ASTM C 1810/C1810M : 2021 : REV A | Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures |
| ASTM C 28/C28M : 2010 : R2020 | Standard Specification for Gypsum Plasters |
| ASTM C 1567 : 2021 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
| ASTM D 4570 : 2002 : R2021 | Standard Test Method for Rubber Chemicals—Determination of Particle Size of Sulfur by Sieving (Dry) |
| ASTM A 568/A568M : 2019 : REV A | Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for |
| ASTM C 999 : 2017 | Standard Practice for Soil Sample Preparation for the Determination of Radionuclides |
| ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM C 295/C295M : 2019 | Standard Guide for Petrographic Examination of Aggregates for Concrete |
| ASTM C 602 : 2020 | Standard Specification for Agricultural Liming Materials |
| ASTM D 560/D560M : 2016 | Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures |
| ASTM D 6647 : 2018 | Standard Test Method for Determination of Acid Soluble Iron via Atomic Absorption |
| ASTM C 604 : 2018 | Standard Test Method for True Specific Gravity of Refractory Materials by Gas-Comparison Pycnometer |
| ASTM C 429 : 2021 | Standard Test Method for Sieve Analysis of Raw Materials for Glass Manufacture |
| ASTM D 452/D452M : 2019 | Standard Test Method for Sieve Analysis of Surfacing for Asphalt Roofing Products |
| ASTM C 1065 : 2008 : R2015 | Standard Specification for Nuclear-Grade Zirconium Oxide Powder |
| ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM C 708 : 2016 | Standard Specification for Nuclear-Grade Beryllium Oxide Powder (Withdrawn 2024) |
| ASTM D 3997/D3997M : 2016 | Standard Practice for Preparing Coke Samples for Microscopical Analysis by Reflected Light |
| ASTM D 4616 : 1995 : R2018 | Standard Test Method for Microscopical Analysis by Reflected Light and Determination of Mesophase in a Pitch |
| ASTM D 968 : 2017 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM C 311/C311M : 2022 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
| ASTM A 835/A835M : 2010 : R2020 | Standard Specification for Sizes of Ferroalloys and Alloy Additives |
| ASTM D 1139/D1139M : 2015 | Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments |
| ASTM F 106 : 2012 : R2017 | Standard Specification for Brazing Filler Metals for Electron Devices (Withdrawn 2024) |
| ASTM C 332 : 2017 | Standard Specification for Lightweight Aggregates for Insulating Concrete |
| ASTM D 448 : 2012 : R2017 | Standard Classification for Sizes of Aggregate for Road and Bridge Construction |
| ASTM C 1093 : 2022 | Standard Practice for Accreditation of Testing Agencies for Masonry |
| ASTM D 5004 : 2011 : R2017 | Standard Test Method for Real Density of Calcined Petroleum Coke by Xylene Displacement |
| ASTM D 7226 : 2013 : R2017 | Standard Test Method for Determining the Viscosity of Emulsified Asphalts Using a Rotational Paddle Viscometer |
| ASTM D 7626 : 2019 : EDT 1 | Standard Test Methods for Determining the Organic Treat Loading of Organophilic Clay |
| ASTM D 2489/D2489M : 2016 | Standard Test Method for Estimating Degree of Particle Coating of Asphalt Mixtures |
| ASTM D 4930 : 2006 : R2017 | Standard Test Method for Dust Control Material on Calcined Petroleum Coke |
| ASTM A 99 : 2003 : R2019 | Standard Specification for Ferromanganese |
| ASTM B 214 : 2016 | Standard Test Method for Sieve Analysis of Metal Powders |
| ASTM D 2171/D2171M : 2018 | Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer |
| ASTM D 5092/D5092M : 2016 | Standard Practice for Design and Installation of Groundwater Monitoring Wells |
| ASTM D 4746 : 2020 | Standard Test Method for Determination of Quinoline Insolubles (QI) in Tar and Pitch by Pressure Filtration |
| ASTM D 3977 : 1997 : R2019 | Standard Test Methods for Determining Sediment Concentration in Water Samples |
| ASTM D 4326 : 2021 | Standard Test Method for Major and Minor Elements in Coal Ash By X-Ray Fluorescence |
| ASTM C 441/C441M : 2017 | Standard Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction |
| ASTM A 922 : 2005 : R2020 | Standard Specification for Silicon Metal |
| ASTM C 1843 : 2016 : R2022 | Standard Test Method for Determining Moisture Content in Uranium-Ore Concentrate |
| ASTM D 2977 : 2014 | Standard Practice for Particle Size Range of Peat Materials for Horticultural Purposes |
| ASTM D 1665 : 2020 | Standard Test Method for Engler Specific Viscosity of Tar Products (Withdrawn 2023) |
| ASTM D 2320 : 1998 : R2017 | Standard Test Method for Density (Relative Density) of Solid Pitch (Pycnometer Method) |
| ASTM F 2075 : 2020 | Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment |
| ASTM C 980 : 2017 | Standard Specification for Industrial Chimney Lining Brick |
| ASTM D 4254 : 2016 | Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density |
| ASTM D 502 : 1989 : R2016 | Standard Test Method for Particle Size of Soaps and Other Detergents |
| ASTM D 8378/D8378M : 2021 | Standard Test Method for Potential Expansion of Steel Slag from Hydration Reactions by Autoclave |
| ASTM D 716 : 1986 : R2019 | Standard Test Methods for Evaluating Mica Pigment |
| ASTM D 6092 : 2021 | Standard Practice for Specifying Standard Sizes of Stone for Erosion Control |
| ASTM D 440 : 2007 : R2019 : EDT 1 | Standard Test Method of Drop Shatter Test for Coal |
| ASTM E 2316 : 2014 : R2019 : EDT 1 | Standard Test Method for Determination of Particles Resulting from the Attrition of Granular Pesticides |
| ASTM D 6998 : 2019 | Standard Practice for Evaluating Aggregate Coating using Emulsified Asphalts |
| ASTM D 1155 : 2010 : R2020 | Standard Test Method for Roundness of Glass Spheres |
| ASTM C 472 : 2020 | Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters, and Gypsum Concrete |
| ASTM D 50 : 1990 : R2019 | Standard Test Methods for Chemical Analysis of Yellow, Orange, Red, and Brown Pigments Containing Iron and Manganese |
| ASTM D 1511 : 2012 : R2017 | Standard Test Method for Carbon Black—Pellet Size Distribution |
| ASTM F 3055 : 2014 : REV A : R2021 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
| ASTM D 409/D409M : 2016 | Standard Test Method for Grindability of Coal by the Hardgrove-Machine Method |
| ASTM E 2814 : 2022 | Standard Specification for Industrial Woven Wire Filter Cloth |
| ASTM E 956 : 1983 : R2015 | Standard Classification for Municipal-Mixed Nonferrous Metals (MNM) |
| ASTM D 1214 : 2010 : R2020 | Standard Test Method for Sieve Analysis of Glass Spheres |
| ASTM D 854 : 2014 | Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023) |
| ASTM C 123/C123M : 2014 | Standard Test Method for Lightweight Particles in Aggregate (Withdrawn 2023) |
| ASTM D 2488 : 2017 : EDT 1 | Standard Practice for Description and Identification of Soils (Visual-Manual Procedures) |
| ASTM E 2651 : 2019 | Standard Guide for Powder Particle Size Analysis |
| ASTM D 1514 : 2015 : R2020 | Standard Test Method for Carbon Black—Sieve Residue |
| ASTM D 4959 : 2016 | Standard Test Method for Determination of Water Content of Soil By Direct Heating |
| ASTM D 1278 : 1991 : REV A : R2020 | Standard Test Methods for Rubber from Natural Sources—Chemical Analysis |
| ASTM C 88/C88M : 2018 | Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate |
| ASTM C 1098 : 2008 : R2015 | Standard Specification for Nuclear-Grade Hafnium Oxide Powder |
| ASTM E 161 : 2017 : R2021 | Standard Specification for Electroformed Material and Test Sieves |
| ASTM F 1864 : 2021 | Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings |
| ASTM D 2844/D2844M : 2018 | Standard Test Method for Resistance <emph type="bdit">R</emph>-Value and Expansion Pressure of Compacted Soils |
| ASTM C 566 : 2019 | Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying |
| ASTM D 4643 : 2017 | Standard Test Method for Determination of Water Content of Soil and Rock by Microwave Oven Heating |
| ASTM E 2016 : 2022 | Standard Specification for Industrial Woven Wire Cloth |
| ASTM D 1748 : 2010 : R2015 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 5493 : 2006 : R2016 | Standard Test Method for Permittivity of Geotextiles Under Load |
| ASTM C 1891 : 2020 | Standard Test Method for Fineness of Hydraulic Cement by Air Jet Sieving at 45-µm (No. 325) |
| ASTM F 1815 : 2011 : R2018 | Standard Test Methods for Saturated Hydraulic Conductivity, Water Retention, Porosity, and Bulk Density of Athletic Field Rootzones |
| ASTM C 61/C61M : 2000 : R2020 | Standard Specification for Gypsum Keene's Cement |
| ASTM D 7428 : 2015 | Standard Test Method for Resistance of Fine Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus |
| ASTM D 2978 : 2015 : EDT 1 | Standard Test Methods for Volume of Processed Peat Materials |
| ASTM A 610 : 1979(R2019) | Standard Test Methods for Sampling and Testing Ferroalloys for Determination of Size |
| ASTM D 197 : 2019 | Standard Test Method for Sampling and Fineness Test of Pulverized Coal |
| ASTM C 131/C131M : 2020 | Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine |
| ASTM F 2107 : 2008 : R2020 | Standard Guide for Construction and Maintenance of Skinned Areas on Baseball and Softball Fields |
| ASTM D 1241 : 2015 | Standard Specification for Materials for Soil-Aggregate Subbase, Base, and Surface Courses (Withdrawn 2024) |
| ASTM C 35 : 2001(R2019) | Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster |
| ASTM B 611 : 2021 | Standard Test Method for Determining the High Stress Abrasion Resistance of Hard Materials |
| ASTM F 1580 : 2018 | Standard Specification for Titanium and Titanium-6 Aluminum-4 Vanadium Alloy Powders for Coatings of Surgical Implants |
| ASTM D 4253 : 2016 : EDT 1 | Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table |
| ASTM D 8135 : 2017 | Standard Guide for Selection of Substitute, Non-hazardous, Particulate Solid Filling Substances for Packagings Subjected to the United Nations Performance Tests |
| ASTM D 4931 : 2006 : R2017 | Standard Test Method for Gross Moisture in Green Petroleum Coke |
| ASTM A 749/A749M : 2014 : R2021 | Standard Specification for Steel, Strip, Carbon and High-Strength, Low-Alloy, Hot-Rolled, General Requirements for |
| ASTM D 6913/D6913M : 2017 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASTM D 2638 : 2021 | Standard Test Method for Real Density of Calcined Petroleum Coke by Helium Pycnometer |
| ASTM D 2013/D2013M : 2021 | Standard Practice for Preparing Coal Samples for Analysis |
| ASTM D 4350 : 2016 | Standard Test Method for Corrosivity Index of Plastics and Fillers |
| ASTM C 786/C786M : 2017 | Standard Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-μm (No. 50), 150-μm (No. 100), and 75-μm (No. 200) Sieves by Wet Methods |
| ASTM D 7280 : 2020 | Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch by Stainless Steel Crucible Filtration |
| ASTM F 1953 : 2010 : R2018 | Standard Guide for Construction and Maintenance of Grass Tennis Courts |
| ASTM D 3280 : 1985 : R2020 | Standard Test Methods for Analysis of White Zinc Pigments |
| ASTM C 225 : 1985 : R2014 | Standard Test Methods for Resistance of Glass Containers to Chemical Attack |
| ASTM D 5158 : 1998 : R2019 | Standard Test Method for Determination of Particle Size of Powdered Activated Carbon by Air-Jet Sieving |
| ASTM C 780 : 2020 | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
| ASTM C 939/C939M : 2016 : REV A | Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method) |
| ASTM F 3012 : 2022 | Standard Specification for Loose-Fill Rubber for Use as a Playground Safety Surface under and around Playground Equipment |
| ASTM F 608 : 2018 | Standard Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners |
| ASTM D 4749/D4749M : 1987 : R2019 : EDT 1 | Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size |
| ASTM D 4892 : 2014 : R2019 : EDT 1 | Standard Test Method for Density of Solid Pitch (Helium Pycnometer Method) |
| ASTM E 2397/E2397M : 2019 | Standard Practice for Determination of Dead Loads and Live Loads Associated with Vegetative (Green) Roof Systems |
| ASTM D 5080 : 2020 | Standard Test Method for Rapid Determination of Percent Compaction |
| ASTM D 2980 : 2017 : EDT 1 | Standard Test Method for Saturated Density, Moisture-Holding Capacity, and Porosity of Saturated Peat Materials |
| ASTM C 1387 : 2014 | Standard Guide for the Determination of Technetium-99 in Soil |
| ASTM D 1739 : 1998 : R2017 | Standard Test Method for Collection and Measurement of Dustfall (Settleable Particulate Matter) |
| ASTM C 1524 : 2020 | Standard Test Method for Water-Extractable Chloride in Aggregate (Soxhlet Method) |
| ASTM D 1742 : 2020 | Standard Test Method for Oil Separation from Lubricating Grease During Storage |
| ASTM D 8198 : 2018 | Standard Specification for Hydraulically Applied 100 % Wood Fiber Mulches |
| ASTM D 718 : 1986 : R2020 | Standard Test Methods for Analysis of Aluminum Silicate Pigment |
| ASTM D 4792/D4792M : 2013 : R2019 | Standard Test Method for Potential Expansion of Aggregates from Hydration Reactions |
| ASTM D 6926 : 2020 | Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus |
| ASTM C 1218/C1218M : 2020 | Standard Test Method for Water-Soluble Chloride in Mortar and Concrete |
| ASTM A 601/A601M : 2010 : R2020 | Standard Specification for Electrolytic Manganese Metal |
| ASTM D 4607 : 2014 : R2021 | Standard Test Method for Determination of Iodine Number of Activated Carbon |
| ASTM D 1557 : 2012 : R2021 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>)) |
| ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
| ASTM C 142/C142M : 2017 | Standard Test Method for Clay Lumps and Friable Particles in Aggregates |
| ASTM D 1863/D1863M : 2005 : R2018 | Standard Specification for Mineral Aggregate Used on Built-Up Roofs |
| ASTM D 4914/D4914M : 2016 | Standard Test Methods for Density of Soil and Rock in Place by the Sand Replacement Method in a Test Pit |
| ASTM C 1746/C1746M : 2019 | Standard Test Method for Measurement of Suspended Sediment Removal Efficiency of Hydrodynamic Stormwater Separators and Underground Settling Devices |
| ASTM C 59/C59M : 2000 : R2020 | Standard Specification for Gypsum Casting Plaster and Gypsum Molding Plaster |
| ASTM D 6936 : 2017 | Standard Test Method for Determining Demulsibility of Emulsified Asphalt |
| ASTM E 2399/E2399M : 2019 | Standard Test Method for Maximum Media Density for Dead Load Analysis of Vegetative (Green) Roof Systems |
| ASTM D 1632 : 2017 : EDT 1 | Standard Practice for Making and Curing Soil-Cement Compression and Flexure Test Specimens in the Laboratory |
| ASTM C 1090/C1090M : 2015 | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout |
| ASTM D 2487 : 2017 : EDT 1 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 1921 : 2018 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials |
| ASTM C 784 : 2020 | Standard Specification for Nuclear-Grade Aluminum Oxide-Boron Carbide Composite Pellets |
| ASTM C 1777 : 2020 | Standard Test Method for Rapid Determination of the Methylene Blue Value for Fine Aggregate or Mineral Filler Using a Colorimeter |
| ASTM D 5030/D5030M : 2021 | Standard Test Methods for Density of In-Place Soil and Rock Materials by the Water Replacement Method in a Test Pit |
| ASTM D 185 : 2007 : R2019 | Standard Test Methods for Coarse Particles in Pigments |
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM D 6997 : 2012 : R2020 | Standard Test Method for Distillation of Emulsified Asphalt |
| ASTM D 6376 : 2010 : R2017 : EDT 1 | Standard Test Method for Determination of Trace Metals in Petroleum Coke by Wavelength Dispersive X-ray Fluorescence Spectroscopy |
| ASTM F 3001 : 2014 : R2021 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium ELI (Extra Low Interstitial) with Powder Bed Fusion |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 494 : 2011(R2019) | Standard Test Method for Acetone Extraction of Phenolic Molded or Laminated Products |
| ASTM C 24 : 2009 : R2018 | Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High-Alumina Refractory Materials |
| ASTM E 2543 : 2008 : R2014 | Standard Specification for Portable Air Heaters Used at Personnel Decontamination Stations and Shelters |
| ASTM D 7367 : 2019 : EDT 2 | Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting |
| ASTM D 632 : 2012 : R2020 : EDT 1 | Standard Specification for Sodium Chloride |
| ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
| ASTM D 5106 : 2015 | Standard Specification for Steel Slag Aggregates for Bituminous Paving Mixtures |
| ASTM D 7496 : 2018 | Standard Test Method for Viscosity of Emulsified Asphalt by Saybolt Furol Viscometer |
| ASTM C 33/C33M : 2018 | Standard Specification for Concrete Aggregates |
| ASTM F 2953 : 2012 : R2021 | Standard Specification for Phenolic Raw Materials for the Use in Bearing Cages |
| ASTM D 451/D451M : 2017 | Standard Test Method for Sieve Analysis of Granular Mineral Surfacing For Asphalt Roofing Products |
| ASTM D 4751 : 2021 : REV A | Standard Test Methods for Determining Apparent Opening Size of a Geotextile |
| ASTM C 778 : 2021 | Standard Specification for Standard Sand |
| ASTM D 5341/D5341M : 2019 | Standard Test Method for Measuring Coke Reactivity Index (CRI) and Coke Strength After Reaction (CSR) |
| ASTM D 698 : 2012 : R2021 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>)) |
| ASTM D 1266 : 2018 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 3038 : 1993 : R2018 | Standard Test Method for Drop Shatter Test for Coke |
| ASTM D 1370/D1370M : 2012 : R2021 | Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test) |
| ASTM C 146 : 2021 | Standard Test Methods for Chemical Analysis of Glass Sand |
| ASTM F 3056 : 2014 : R2021 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
| ASTM D 1633 : 2017 | Standard Test Methods for Compressive Strength of Molded Soil-Cement Cylinders |
| ASTM D 5230 : 2021 | Standard Test Method for Carbon Black—Automated Individual Pellet Hardness |
| ASTM D 4718/D4718M : 2015 | Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles |
| ASTM D 2187 : 2017 | Standard Test Methods and Practices for Evaluating Physical and Chemical Properties of Particulate Ion-Exchange Resins |
| ASTM D 6467 : 2021 : EDT 1 | Standard Test Method for Torsional Ring Shear Test to Determine Drained Residual Shear Strength of Fine-Grained Soils |
| ASTM D 1914 : 1995 : R2014 | Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1883 : 2021 | Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils |
| ASTM C 1335 : 2012 : R2017 | Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation |
| ASTM D 4646 : 2016 | Standard Test Method for 24-h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments |
| ASTM D 2318 : 2020 | Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch |
| ASTM D 1135 : 1986 : R2020 | Standard Test Methods for Chemical Analysis of Blue Pigments |
| ASTM D 2416 : 2020 | Standard Test Method for Coking Value of Tar and Pitch (Modified Conradson) |
| ASTM C 371 : 2009 : R2018 | Standard Test Method for Wire-Cloth Sieve Analysis of Nonplastic Ceramic Powders |
| ASTM F 3187 : 2016 | Standard Guide for Directed Energy Deposition of Metals |
| ASTM D 7655/D7655M : 2012 : R2017 | Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems |
| ASTM D 6390 : 2011 : R2017 | Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures |
| ASTM D 6934 : 2008 : R2016 | Standard Test Method for Residue by Evaporation of Emulsified Asphalt |
| ASTM D 5444 : 2015 | Standard Test Method for Mechanical Size Analysis of Extracted Aggregate |
| ASTM D 7454 : 2019 | Standard Test Method for Determination of Vibrated Bulk Density of Calcined Petroleum Coke using a Semi-Automated Apparatus |
| ASTM C 888 : 2018 | Standard Specification for Nuclear-Grade Gadolinium Oxide (Gd<inf>2</inf>O<inf>3</inf >) Powder |
| ASTM D 4644 : 2016 | Standard Test Method for Slake Durability of Shales and Other Similar Weak Rocks |
| ASTM D 2764 : 2020 | Standard Test Method for Dimethylformamide-Insoluble (DMF-I) Content of Tar and Pitch |
| ASTM D 3402/D3402M : 2016 | Standard Test Method for Tumbler Test for Coke |
| ASTM E 359 : 2017 | Standard Test Methods for Analysis of Soda Ash (Sodium Carbonate) |
| ASTM C 750 : 2018 | Standard Specification for Nuclear-Grade Boron Carbide Powder |
| ASTM G 105 : 2020 | Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests |
| ASTM C 1318 : 2015 : REV A : R2020 | Standard Test Method for Determination of Total Neutralizing Capability and Dissolved Calcium and Magnesium Oxide in Lime for Flue Gas Desulfurization (FGD) |
| ASTM D 8106 : 2017 | Standard Test Methods for Determining the Oil Sorption Capacity of Organophilic Clay |
| ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
| ASTM D 4312 : 2020 | Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method) |
| ASTM C 329 : 1988 : R2020 | Standard Test Method for Specific Gravity of Fired Ceramic Whiteware Materials |
| ASTM D 1275 : 2015 | Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids |
| ASTM C 127 : 2015 | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024) |
| ASTM D 3282 : 2015 | Standard Practice for Classification of Soils and Soil-Aggregate Mixtures for Highway Construction Purposes |
| ASTM C 5 : 2018 | Standard Specification for Quicklime for Structural Purposes |
| ASTM D 2774 : 2021 : REV A | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2419 : 2014 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
| ASTM F 1632 : 2003 : R2018 | Standard Test Method for Particle Size Analysis and Sand Shape Grading of Golf Course Putting Green and Sports Field Rootzone Mixes |
| ASTM E 2542 : 2008 : R2014 | Standard Specification for Portable Water Heaters Used at Personnel Decontamination Stations |
| ASTM C 400 : 2019 | Standard Test Methods for Quicklime and Hydrated Lime for Neutralization of Waste Acid |
| ASTM D 1865/D1865M : 2009 : R2017 | Standard Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs |
| ASTM D 4026 : 2006 : R2021 | Standard Test Method for Rubber Latex—Styrene-Butadiene Copolymer—Determination of Residual Styrene |
| ASTM D 7928 : 2021 : EDT 1 | Standard Test Method for Particle-Size Distribution (Gradation) of Fine-Grained Soils Using the Sedimentation (Hydrometer) Analysis |
| ASTM C 1463 : 2019 | Standard Practices for Dissolving Glass Containing Radioactive and Mixed Waste for Chemical and Radiochemical Analysis |
| ASTM C 232/C232M : 2021 | Standard Test Method for Bleeding of Concrete |
| ASTM D 5514/D5514M : 2018 | Standard Test Method for Large-Scale Hydrostatic Puncture Testing of Geosynthetics |
| ASTM D 8281/D8281M : 2021 | Standard Test Method for Determining the Presence of Expanding Clays in Rock for Erosion Control Using Ethylene Glycol |
| ASTM A 132 : 2004 : R2019 | Standard Specification for Ferromolybdenum |
| ASTM D 8097 : 2017:EDT 1 | Standard Test Method for Determination of Bulk Density for Specific Size Fractions of Calcined Petroleum Coke Using a Transaxial Pressure Pycnometer |
| ASTM E 389 : 2021 | Standard Test Method for Particle Size or Screen Analysis at 4.75 mm (No.4) Sieve and Coarser for Metal-Bearing Ores and Related Materials |
| ASTM C 535 : 2016 | Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine |
| ASTM D 546 : 2017 | Standard Test Method for Sieve Analysis of Mineral Filler for Asphalt Paving Mixtures |
| ASTM F 104 : 2011 : R2020 | Standard Classification System for Nonmetallic Gasket Materials |
| ASTM D 8262 : 2022 | Standard Test Method for Determining the pH of Granular Material for Use in Embankments, Subgrades, and Retaining Wall Backfil |
| ASTM C 1077 : 2017 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM D 6276 : 2019 | Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization |
| ASTM E 728 : 1991 : R2020 | Standard Test Method for Resistance to Attrition of Granular Carriers and Granular Pesticides |
| ASTM C 325 : 2007 : R2022 | Standard Guide for Wet Sieve Analysis of Ceramic Whiteware Clays |
| ASTM C 1761/C1761M : 2017 | Standard Specification for Lightweight Aggregate for Internal Curing of Concrete |
| ASTM D 1319 : 2020 : REV A | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 269 : 1997 : R2020 | Standard Test Method for Insoluble Matter in Rosin and Rosin Derivatives |
| ASTM E 1706 : 2020 | Standard Test Method for Measuring the Toxicity of Sediment-Associated Contaminants with Freshwater Invertebrates |
| ASTM C 136/C136M : 2019 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
| ASTM D 7521 : 2016 | Standard Test Method for Determination of Asbestos in Soil |
| ASTM D 3802 : 2016 | Standard Test Method for Ball-Pan Hardness of Activated Carbon |
| ASTM F 2924 : 2014 : R2021 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion |
| ASTM D 1140 : 2017 | Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing |
| ASTM D 2332 : 2013 : R2021 | Standard Practice for Analysis of Water-Formed Deposits by Wavelength-Dispersive X-Ray Fluorescence |
| ASTM F 2363/F2363M : 2017 | Standard Specification for Sewage and Graywater Flow Through Treatment Systems |
| ASTM D 480 : 1988 : R2020 | Standard Test Methods for Sampling and Testing of Flaked Aluminum Powders and Pastes |
| ASTM D 8012 : 2018 | Standard Practice for Reclamation of Scrap and Waste Asphalt Shingles to Produce Reclaimed Asphalt Shingles (RAS) for Use in Transportation Applications |
| ASTM C 374 : 2014 : R2018 | Standard Test Methods for Fusion Flow of Porcelain Enamel Frits (Flow-Button Methods) |
| ASTM D 5159 : 2021 | Standard Guide for Dusting Attrition of Granular Activated Carbon |
| ASTM C 29/C29M : 2017 : REV A | Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate |
| ASTM D 4318 : 2017 : EDT 1 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 5600 : 2017 | Standard Test Method for Trace Metals in Petroleum Coke by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM E 323 : 2011 : R2021 | Standard Specification for Perforated-Plate Sieves for Testing Purposes |
| ASTM E 323 : 2011 : R2016 | Standard Specification for Perforated-Plate Sieves for Testing Purposes |
| ASTM E 1638 : 2007 | Standard Terminology Relating to Sieves, Sieving Methods and Screening Media |
| ASTM E 161 : 2017 | Standard Specification for Electroformed Material and Test Sieves |
| ASTM E 161 : 2017 : R2021 | Standard Specification for Electroformed Material and Test Sieves |
| ASTM E 2016 : 2020 | Standard Specification for Industrial Woven Wire Cloth |
| ASTM E 2016 : 1999 | Standard Specification for Industrial Woven Wire Cloth |
| ASTM E 2016 : 2022 | Standard Specification for Industrial Woven Wire Cloth |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.