UNE-EN ISO 11403-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014)
Hardcopy , PDF
08-06-2022
Spanish, Castilian, English
12-11-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Term and definition
4 Specimen preparation
5 Conditioning
6 Test requirements
6.1 General
6.2 Dynamic modulus: ISO 6721-2 or ISO 6721-4
6.3 Tensile properties at constant test
speed: ISO 527-1 and ISO 527-2
6.4 Tensile creep: ISO 899-1
6.5 Charpy impact strength: ISO 179-1 or ISO
179-2
6.6 Puncture impact behaviour
7 Presentation of data
8 Precision
Annex A (informative) Other properties
A.1 General
A.2 Fracture-mechanics parameters
A.3 Fatigue
A.4 Creep rupture
Bibliography
Defines test procedures for the acquisition and presentation of multipoint data on specified mechanical properties of plastics. Applies predominantly to those plastics that can be compression- or injection-moulded or prepared as sheets of defined thickness from which appropriately sized specimens can be machined.
| Committee |
CTN 53/SC 6
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
Asociacion Espanola de Normalizacion
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN ISO 11403-1 : 2014 | Identical |
| ISO 11403-1:2014 | Identical |
| NBN EN ISO 11403-1 : 2014 | Identical |
| NEN EN ISO 11403-1 : 2014 | Identical |
| NS EN ISO 11403-1 : 2014 | Identical |
| I.S. EN ISO 11403-1:2014 | Identical |
| SN EN ISO 11403-1 : 2014 | Identical |
| UNI EN ISO 11403-1 : 2014 | Identical |
| BS EN ISO 11403-1:2014 | Identical |
| EN ISO 11403-1:2014 | Identical |
| DIN EN ISO 11403-1:2014-09 | Identical |
| DIN EN ISO 11403-1:2003-09 | Identical |
| ONORM EN ISO 11403-1 : 2014 | Identical |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 15850:2014 | Plastics — Determination of tension-tension fatigue crack propagation — Linear elastic fracture mechanics (LEFM) approach |
| ISO 6721-2:2008 | Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 17281:2002 | Plastics Determination of fracture toughness (GIC and KIC) at moderately high loading rates (1 m/s) |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 6721-4:2008 | Plastics Determination of dynamic mechanical properties Part 4: Tensile vibration Non-resonance method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 13586:2000 | Plastics Determination of fracture toughness (GIC and KIC) Linear elastic fracture mechanics (LEFM) approach |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.