UNE 53940:2010
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics. Polyethylene (PE) fabricated fittings for piping systems for water supply under pressure
Available format(s)
Hardcopy , PDF
Superseded date
03-05-2012
Superseded by
Language(s)
Spanish, Castilian
Published date
21-07-2010
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
CTN 53/SC 2
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
Asociacion Espanola de Normalizacion
|
| Status |
Superseded
|
| SupersededBy |
| UNE-EN ISO 1043-1:2012 | Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2011) |
| UNE-EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| UNE-ISO 13953:2011 | Polyethylene (PE) pipes and fittings. Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| UNE-EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO 4427-3:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
| UNE-EN 13244-3:2003 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
| UNE-EN 13244-5:2003 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| UNE-EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| ISO 4433-1:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
| UNE 53389:2001 IN | Plastics pipes and fittings. Combined chemical-resistance classification table. |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| UNE-EN 12201-2:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| UNE-EN 12201-5:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| UNE-EN 12201-1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| ISO 4433-2:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes |
| UNE 53394:2006 IN | Plastics. Code for the installation and handling of polyethylene (PE) pipes for water piping under pressure. Recommended techniques |
| UNE-EN ISO 1167-3:2008 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007) |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 9624:1997 | Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges |
| UNE-EN ISO 472:2015 | Plastics - Vocabulary (ISO 472:2013) |
| UNE-EN ISO 1133:2006 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| UNE-EN 13244-4:2003 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.