SAE J 2698 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRIMARY SINGLE PHASE NOMINAL 120 VAC WIRING DISTRIBUTION ASSEMBLY DESIGN - TRUCK AND BUS
Hardcopy , PDF
10-08-2020
English
01-01-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. WIRING
5. TERMINAL AND CONNECTION FUNCTION
(NON-SUPPLY POINT)
6. SUPPLY CONNECTIONS
7. RECEPTACLES
8. OVERCURRENT AND FAULT PROTECTION
9. SWITCHES AND CONTROLS
10. GROUNDING AND BONDING
11. COMPONENT/SYSTEM TESTING AND APPROVAL
12. WIRING CIRCUIT INSTALLATION AND PROTECTION
13. MARKINGS
14. INSTRUCTION MANUAL
15. SEPARATION OF CIRCUITS
16. VOLTAGE DROP
Describes the design and application of primary on-board wiring distribution system harnessing for surface vehicles.
| DocumentType |
Standard
|
| Pages |
10
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE J 2697 : 2017 | INVERTER REQUIREMENTS FOR CLASS EIGHT TRUCKS - TRUCK AND BUS |
| SAE J 2891 : 2015 | AUXILIARY POWER UNIT ELECTRICAL INTERFACE REQUIREMENTS FOR CLASS EIGHT TRUCKS |
| UL 514A:11ED 2013-02-01 | Metallic Outlet Boxes |
| UL 50:13ED 2015-10-16 | Enclosures for Electrical Equipment, Non-Environmental Considerations |
| CSA C22.2 No. 5 : 2013 | MOLDED-CASE CIRCUIT BREAKERS, MOLDED-CASE SWITCHES AND CIRCUIT-BREAKER ENCLOSURES |
| CSA C22.2 No. 49 : 2014 | FLEXIBLE CORDS AND CABLES |
| SAE J 560 : 2016 | PRIMARY AND AUXILIARY SEVEN CONDUCTOR ELECTRICAL CONNECTOR FOR TRUCK-TRAILER JUMPER CABLE |
| CSA C22.2 No. 0.4 : 2004(R2013) | BONDING OF ELECTRICAL EQUIPMENT |
| CSA C22.2 No. 21 : 2014 | CORD SETS AND POWER-SUPPLY CORDS |
| UL 83:16ED 2017-07-28 | Standard for Thermoplastic-Insulated Wires and Cables |
| CSA C22.2 No. 144 : 1991 | GROUND FAULT CIRCUIT INTERRUPTERS |
| SAE J 1673 : 2012 | HIGH VOLTAGE AUTOMOTIVE WIRING ASSEMBLY DESIGN |
| SAE J 447 : 2016 | PREVENTION OF CORROSION OF MOTOR VEHICLE BODY AND CHASSIS COMPONENTS |
| UL 943:5ED 2016-05-17 | Ground-Fault Circuit-Interrupters |
| SAE J 1128 : 2015 | LOW VOLTAGE PRIMARY CABLE |
| UL 514C:4ED 2014-04-08 | Nonmetallic Outlet Boxes, Flush-Device Boxes, and Covers |
| SAE J 1455 : 2017 | RECOMMENDED ENVIRONMENTAL PRACTICES FOR ELECTRONIC EQUIPMENT DESIGN IN HEAVY-DUTY VEHICLE APPLICATIONS |
| SAE J 1908 : 2013 | ELECTRICAL GROUNDING PRACTICE |
| CSA C22.2 No. 65 : 2013 | WIRE CONNECTORS |
| NEMA WD 6 : 2016 | WIRING DEVICES - DIMENSIONAL SPECIFICATIONS |
| SAE J 2223/2 : 2011 | CONNECTIONS FOR ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSES - PART 2: TESTS AND GENERAL PERFORMANCE REQUIREMENTS |
| CSA C22.2 No. 18 : 0 | OUTLET BOXES, CONDUIT BOXES, FITTINGS AND ASSOCIATED HARDWARE |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| SAE J 1654 : 2016 | UNSHIELDED HIGH VOLTAGE PRIMARY CABLE |
| C22.2 NO. 75-17 | Thermoplastic insulated wires and cables (Trinational standard with UL 83 and NMX-J-010-ANCE-2017) |
| SAE J 1742 : 2010 | CONNECTIONS FOR HIGH VOLTAGE ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSES - TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.