SAE J 1273 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RECOMMENDED PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES
Hardcopy , PDF
04-11-2019
English
01-01-2014
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. SAFETY CONSIDERATIONS
5. HOSE SELECTION AND ROUTING
6. HOSE-ASSEMBLY FABRICATION
7. HOSE INSTALLATION AND REPLACEMENT
8. MAINTENANCE INSPECTION
9. HOSE STORAGE
10. NOTES
Gives guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems.
DocumentType |
Standard
|
Pages |
21
|
PublisherName |
SAE International
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
SAE J 533 : 2017 | FLARES FOR TUBING |
SAE J 2593 : 2015 | INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS |
SAE J 1779 : 2013 | SHIP SYSTEMS AND EQUIPMENT - HYDRAULIC SYSTEM DESIGN CRITERIA FOR MARINE VEHICLES |
SAE J 1942 : 2014 | HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS |
SAE J 1453/2 : 2015 | Specification for O-Ring Face Seal Connectors: Part 2 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Braze-on Tube Ends, Caps, and Connectors with ISO 6149-2 Metric Stud Ends and ISO 6162 4-Bolt Flange Heads |
SAE J 1754/2 : 2015 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 2: ORDERING INFORMATION |
SAE J 1754/1 : 2017 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 1: PROCUREMENT DOCUMENT |
SAE J 1927 : 2014 | CUMULATIVE DAMAGE ANALYSIS FOR HYDRAULIC HOSE ASSEMBLIES |
SAE J 1231 : 2016 | FORMED TUBE ENDS FOR HOSE CONNECTIONS AND HOSE FITTINGS |
SAE J 1754/3 : 2015 | HOSE ASSEMBLIES, HYDRAULIC, J517 100R SERIES HOSE - PART 3: PROCUREMENT AND ORDERING INFORMATION |
ANSI B11.25 : 2015 | SAFETY REQUIREMENTS FOR LARGE MACHINES |
ANSI/SPI B151.31:2014 | PLASTICS MACHINERY - SAFETY REQUIREMENTS FOR THE MANUFACTURE AND USE OF BLOW MOLDING MACHINES |
SAE J 2551/3 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT |
SAE AIR 5386 : 2013 | HOSE AND HOSE ASSEMBLY SELECTION, INSTALLATION, INSPECTION AND MAINTENANCE GUIDELINES, LISTING OF |
ANSI/SPI B151.29:2014 | PLASTICS MACHINERY - SAFETY REQUIREMENTS FOR VERTICAL CLAMP INJECTION MOLDING MACHINES |
SAE J 2551/2 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS |
SAE J 2545 : 2014 | TEST PROCEDURES FOR NON-SAE HYDRAULIC HOSES |
ASTM D 8112 : 2017 | Standard Guide for Obtaining In-Service Samples of Turbine Operation Related Lubricating Fluid |
ANSI B71.7 : 1985 | SAFETY SPECIFICATIONS FOR POWERED LOG SPLITTERS |
SAE J 2552 : 2014 | PUSH-ON HOSE AND MATING HOSE FITTINGS |
I.S. 808:2002 | SPECIFICATION FOR CNG FUELLED VEHICLES |
SAE J 517 : 2017 | HYDRAULIC HOSE |
SAE J 1065 : 2016 | NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING |
SAE J 2551 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON AND ALLOY STEEL TUBING APPLICATIONS |
SAE J 2551/1 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 1: DESIGN AND FABRICATION |
SAE J 516 : 2016 | HYDRAULIC HOSE FITTINGS |
SAE J 1754/2 : 2015 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 2: ORDERING INFORMATION |
SAE J 517 : 2016 | HYDRAULIC HOSE |
SAE J 1754/3 : 2015 | HOSE ASSEMBLIES, HYDRAULIC, J517 100R SERIES HOSE - PART 3: PROCUREMENT AND ORDERING INFORMATION |
ISO 2230:2002 | Rubber products — Guidelines for storage |
SAE J 1754/1 : 2013 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 1: PROCUREMENT DOCUMENT |
ISO 8331:2016 | Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance |
SAE J 343 : 2016 | TEST AND TEST PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES |
SAE J 514 : 2012 | HYDRAULIC TUBE FITTINGS |
ISO 3457:2003 | Earth-moving machinery — Guards — Definitions and requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.