SAE AS 4841 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FITTINGS, 37 DEGREES INTERNAL FLARE, FLUID CONNECTION, PROCUREMENT SPECIFICATION
Available format(s)
Hardcopy , PDF
Superseded date
19-03-2020
Superseded by
Language(s)
English
Published date
01-01-2017
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 SCOPE
2 REFERENCES
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 NOTES
APPENDIX A
Specifies the requirements for 37 degrees flared tube fittings or machined internal cone fluid connection fittings for use with 37 degrees external cone, spherical nose and seal ring fittings in all types of aerospace fluid systems.
| Committee |
G-3
|
| DocumentType |
Revision
|
| Pages |
19
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| MIL-DTL-52525-35 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 4-BOLT SPLIT-FLANGE, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-10 Revision D:2011 | Fittings, Hose, Screw-on to 4-Bolt Split-Flange, Straight |
| MIL-DTL-52525-7 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degrees Flare Female Swivel, 90 Degrees Bent Tube, Short Drop |
| MIL-DTL-52525-32 Revision A:2008 | FITTINGS, HOSE, REINFORCED HYDRAULIC HOSE AND CLAMP-HALVES: FIELD ATTACHABLE (REUSABLE), SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, 45 DEGREES BENT TUBE, FOR USE WITH TYPE 100RE FOUR-SPIRAL-WRAP REINFORCEMENT HOSE |
| MIL-DTL-52525-44 Base Document:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-1 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, Straight, SAE-J516 Type, for Assembly with SAE-J517, Type 100R2 Hose |
| MIL-DTL-52525-43 Base Document:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, STRAIGHT |
| MIL-DTL-52525-11 Revision C:2008 | Fittings, Hose, Screw-On to 4-Bolt Split-Flange, 45 Degree Bent Tube |
| AN815 Revision 10:2015 | UNION - FLARED TUBE |
| MIL-DTL-52525-40 Revision B:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, STRAIGHT |
| AN818 Revision 20:2010 | NUT, TUBE COUPLING, SHORT |
| MS9193 Revision A:2010 | NIPPLE, TUBE - SAE-AMS5639, BOSS |
| MIL-DTL-52525-6 Revision C:2008 | Fittings,Hose, Screw-on to 37 Degree Flare Female Swivel, 45Degree BentTube |
| MIL-DTL-52525-36 Revision B:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 90 DEGREES BENT TUBE |
| MS9095 Revision B:2010 | NIPPLE, TUBE - ALUMINUM, BOSS |
| MIL-DTL-52525-15 Revision C:2008 | FITTINGS, HOSE, SCREW-ON TO 4-BOLT SPLIT-FLANGE, 90 DEGREES BENT TUBE |
| SAE AIR 5426 : 2013 | FITTING AND FITTING ASSEMBLY SELECTION, INSTALLATION, INSPECTION AND MAINTENANCE OF |
| AN924 Revision 14:2018 | NUT, TUBE, BULKHEAD AND UNIVERSAL FITTING |
| MIL-DTL-5513 Revision D:2012 | SWIVEL JOINT, HYDRAULIC |
| MS9194 Revision C:2010 | Elbow, Tube - SAE-AMS5646, Boss, 90 Degrees |
| MIL-DTL-52525-13 Revision C:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE STRAIGHT |
| MIL-DTL-52525-5 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, Straight |
| MIL-DTL-52525-34 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 4-BOLT SPLIT-FLANGE, STRAIGHT |
| MIL-DTL-52525-2 Revision C:2008 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 45 Degree Bent Tube |
| AN774 Revision 8:2011 | BOLT - FLARED TUBE FITTING END UNIVERSAL |
| MIL-DTL-83798 Revision D:2008 | FITTING, RUBBER HOSE, LIGHTWEIGHT, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR |
| MIL-DTL-52525-38 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-3 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 90 Degree Bent Tube, Short Drop |
| MS9195 Revision B:2010 | ELBOW, TUBE - SAE-AMS5639, BOSS, 45 DEGREES |
| MIL-DTL-52525-9 Revision C:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, STRAIGHT |
| SAE AS 4875/1 : 2016 | FITTINGS, STRAIGHT THREAD BOSS OR FLANGED 37 DEGREES FLARED, FLUID CONNECTION |
| SAE AS 4842/1 : 2016 | Fittings, 37° Flared to Pipe Threaded, Fluid Connection |
| NASA SSTD 8070 0126 : 2014 | TUBING SYSTEMS FOR FACILITY SYSTEMS, SPECIAL TEST EQUIPMENT, AND AEROSPACE HARDWARE |
| MIL-DTL-52525-17 Revision C:2008 | FITTINGS, CLAMP-HALVES, FLANGE TO PORT, FOR 4-BOLT SPLIT-FLANGE |
| MS9483 Revision C:2010 | FERRULE, BRAZING, TUBE FITTING - CRES SAE-AMS5646, STRAIGHT |
| MIL-DTL-52525-31 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL |
| MIL-DTL-52525 Revision F:2008 | FITTINGS, HOSE, HYDRAULIC, REUSABLE, FIELD-ATTACHABLE AND CLAMP-HALVES, TO MATE WITH SAE-J517 TYPE HOSES, GENERAL SPECIFICATION FOR |
| MS9196 Revision C:2015 | TEE, TUBE - SAE-AMS5646, BOSS |
| MS28754 Revision E:2012 | FITTING END, SELF-SEALING FUEL HOSE, SWIVEL, DETACHABLE, FLANGED, 45 DEGREES |
| AN929 Revision 14:2017 | CAP INSERT, ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING |
| MIL-DTL-5070 Revision F:2006 | ADAPTER, HOSE TO TUBE, PIPE AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR |
| MS28753 Revision E:2012 | FITTING END, SELF-SEALING FUEL HOSE, SWIVEL, DETACHABLE, FLANGED, STRAIGHT |
| MIL-DTL-52525-16 Revision D:2008 | FITTINGS, CLAMP-HALVES, FOR 4-BOLT SPLIT-FLANGE, SAE-J518, TYPE SPLIT-FLANGE CLAMP (SFC) |
| MIL-DTL-52525-37 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, STRAIGHT |
| MIL-DTL-52525-45 Base Document:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 90 DEGREES BENT TUBE |
| MIL-DTL-52525-8 Revision C:2008 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 90 DegreeBent Tube, Long Drop |
| MIL-DTL-52525-39 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37DEGREES FLARE FEMALE SWIVEL, 90 DEGREES BENT TUBE |
| MIL-DTL-52525-14 Revision C:2008 | FITTINGS, HOSE CRIMP TYPE, SPLIT-FLANGE 45 DEGREES BENT |
| MIL-DTL-52525-42 Revision B:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE 90 DEGREES BENT |
| MIL-DTL-52525-41 Revision A:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-12 Revision D:2011 | Fittings, Hose, Screw on to Split-Flange 90 Degree Bent |
| MIL-DTL-52525-33 Revision A:2008 | FITTINGS, WIRE REINFORCED HYDRAULIC HOSE AND CLAMP-HALVES: FIELD ATTACHABLE (REUSABLE), SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, 90 DEGREES BENT TUBE, FOR USE WITH TYPE 100RE FOUR-SPRIAL-WRAP REINFORCEMENT HOSE |
| MS28755 Revision E:2012 | FITTING END, SELF-SEALING FUEL HOSE, SWIVEL, DETACHABLE, FLANGED, 90 DEGREES |
| MIL-DTL-52525-4 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 90 Degree Bent Tube, Long Drop |
| SAE AS 4444/2 : 2015 | Fitting, 24° Cone Flareless to 37° Flared, Fluid Connection |
| SAE AS 4843/1 : 2016 | FITTINGS, BEADED TO 37 DEGREES FLARED, FLUID CONNECTION |
| SAE AS4396B | FITTING END, BULKHEAD, FLARED TUBE CONNECTION, DESIGN STANDARD |
| SAE AS 5309 : 2015 | FITTING END, SPHERICAL, 37 DEGREE FLARED TUBE CONNECTION DESIGN STANDARD |
| SAE AMS5645S | STEEL, CORROSION AND HEAT RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 18CR - 10NI - 0.40TI (321), SOLUTION HEAT TREATED |
| SAE AMS QQ A 225/9 : 2014 | ALUMINUM ALLOY 7075, BAR, ROD, WIRE, AND SPECIAL SHAPES; ROLLED, DRAWN, OR COLD FINISHED |
| MIL-PRF-6083 Revision G:2013 | HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION |
| ASTM B 154 : 2016 : REDLINE | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
| SAE AMSQQP416E | PLATING, CADMIUM (ELECTRODEPOSITED) |
| SAE AMS4133E | ALUMINUM ALLOY FORGINGS AND ROLLED RINGS, 4.4CU - 0.85SI - 0.80MN - 0.50MG (2014-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 2488 : 2000 | ANODIC TREATMENT - TITANIUM AND TITANIUM ALLOYS SOLUTION PH 13 OR HIGHER |
| SAE AS5176C | FITTING, SLEEVE, FLARED |
| SAE AS 5203 : 2013 | TUBE END, DOUBLE FLARE, DESIGN STANDARD |
| SAE AMS 2770 : 2015 | HEAT TREATMENT OF WROUGHT ALUMINUM ALLOY PARTS |
| SAE AMS6382P | STEEL, BARS, FORGINGS, AND RINGS 0.95CR - 0.20MO (0.38 - 0.43C) (SAE 4140) ANNEALED |
| SAE AS1708F | FITTING END, INTERNAL FLARE, DESIGN STANDARD |
| SAE AS4395B | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
| SAE AMS4141G | ALUMINUM ALLOY DIE FORGINGS, 5.6ZN - 2.5MG - 1.6CU - 0.23CR (7075-T73), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS2759E | HEAT TREATMENT OF STEEL PARTS, GENERAL REQUIREMENTS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS5648M | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 17CR - 12NI - 2.5MO (316), SOLUTION HEAT TREATED |
| SAE AS 4330 : 2014 | TUBING, FLARED, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
| MIL-DTL-83488 Revision D:1999 | COATING, ALUMINUM, HIGH PURITY |
| SAE AS 33583 : 2015 | TUBING END DOUBLE FLARE, STANDARD DIMENSIONS FOR |
| SAE AMS5646P | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 18CR - 11NI - 0.60CB(NB) (347), SOLUTION HEAT TREATED |
| SAE AMS 2772 : 2016 | HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| A-A-59133 Revision B:2010 | CLEANING COMPOUND, HIGH PRESSURE (STEAM) CLEANER |
| SAE AS1376D | ALTERNATE DIMENSIONS, CENTER BODY SECTION, SHAPE FLUID FITTING, DESIGN STANDARD |
| SAE AS 71051 : 2015 | PIPE THREADS, TAPER, AERONAUTICAL NATIONAL FORM, SYMBOL ANPT - DESIGN AND INSPECTION STANDARD |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AS 5310 : 2015 | FITTING END, BULKHEAD, SPHERICAL, 37° FLARED TUBE CONNECTION DESIGN STANDARD |
| SAE AMS2472G | ANODIC TREATMENT OF ALUMINUM ALLOYS, SULFURIC ACID PROCESS, DYED COATING |
| SAE AMS2700E | PASSIVATION OF CORROSION RESISTANT STEELS |
| MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
| SAE AMS5639J | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 19CR - 10NI, SOLUTION HEAT TREATED |
| SAE AMS6370P | STEEL, BARS, FORGINGS, AND RINGS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AMS4610N | BRASS, FREE-CUTTING BARS AND RODS 61.5CU - 35ZN - 3.1PB HALF HARD (H02) |
| SAE AMSQQA225/6A | ALUMINUM ALLOY, 2024, BAR, ROD, AND WIRE; ROLLED, DRAWN, OR COLD FINISHED |
| SAE AMS H 6875 : 2010 | HEAT TREATMENT OF STEEL RAW MATERIALS |
| SAE AMS4339A | ALUMINUM ALLOY, ROLLED OR COLD FINISHED BARS AND RODS 4.4CU - 1.5MG - 0.60MN (2024-T-851) SOLUTION HEAT TREATED, COLD WORKED, AND ARTIFICIALLY AGED |
| SAE ARP4784A | DEFINITIONS AND LIMITS, METAL MATERIAL DEFECTS AND SURFACE AND EDGE FEATURES, FLUID COUPLINGS, FITTINGS AND HOSE ENDS |
| SAE AS478N | IDENTIFICATION MARKING METHODS |
| SAE AMS S 6758 : 2013 | STEEL, CHROME-MOLYBDENUM (4130) BARS AND REFORGING STOCK (AIRCRAFT QUALITY) |
| SAE AMS5666H | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, EXTRUSIONS, AND RINGS, 62NI - 21.5CR - 9.0MO - 3.65CB (NB), ANNEALED |
| SAE AS 5202 : 2005 | PORT OR FITTING END, INTERNAL STRAIGHT THREAD, DESIGN STANDARD |
| FED-STD-595 Revision C:2008 | COLORS USED IN GOVERNMENT PROCUREMENT |
| SAE AMS2658D | HARDNESS AND CONDUCTIVITY INSPECTION OF WROUGHT ALUMINUM ALLOY PARTS |
| SAE ARP 9013 : 2005 | STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| SAE AMS4124E | ALUMINUM ALLOY, ROLLED OR COLD FINISHED BARS, RODS, AND WIRE - 5.6ZN - 2.5MG - 1.6CU - 0.23CR (7075-T7351), SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING, AND OVERAGED |
| MS21344 Revision A:2016 | FITTING INSTALLATION OF FLARED TUBE STRAIGHT THREADED CONNECTORS DESIGN STANDARD FOR |
| SAE AMS4928V | TITANIUM ALLOY BARS, WIRE, FORGINGS, RINGS, AND DRAWN SHAPES, 6AL - 4V, ANNEALED |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.