SAE AMS4150M
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Aluminum Alloy, Extrusions and Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6) Solution and Precipitation Heat Treated
19-04-2013
17-05-2019
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
Specifies an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash welded rings fabricated from extruded stock, and stock for flash welded rings.
| DevelopmentNote |
Supersedes SAE AMS 4155 (07/1999)
|
| DocumentType |
Standard
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing, flash welded rings fabricated from extruded stock, and stock for flash welded rings.
| Standards | Relationship |
| QQ-A-200-8 Revision F:1983 | Similar to |
| MIL-DTL-28754-62 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center, Crossover, Contact Tails on .050 Centers |
| MIL DTL 28754/60 : A | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS |
| MIL-DTL-28754-59 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center Contact Tails on .100 Centers (Ceramic Compatible) |
| MIL-DTL-83798 Revision D:2008 | Fitting, Rubber Hose, Lightweight, Medium Pressure, General Specification For |
| MIL-DTL-28754-101 Revision A:2015 | Connectors, Electrical, Modular, Type IV, Connector, 0.6 Pitch, 250 Contact, Center |
| SAE AS269J | Identification of Material for AN, MS, and AS Engine and Propeller Standard Utility Parts and Also for Company Parts |
| MIL-DTL-28754-100 Revision A:2015 | Connectors, Electrical, Modular, Type IV, Connector, 200 Contact, Center |
| MIL-DTL-28754-61 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center, Crossover, Contact Tails on .100 Centers (Ceramic Compatible) |
| MIL-DTL-55302-78 Revision D:2004 | Connectors, Printed Circuit Subassembly and Accessories: Key, Polarizing, Connectors, Electrical Printed Wiring Boards |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| ASTM B 807/B807M : 2013 : REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
| ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
| SAE AMS7488F | Rings, Flash Welded Aluminum and Aluminum Alloys |
| SAE AMS2772G | Heat Treatment of Aluminum Alloy Raw Materials |
| SAE AS1990D | Aluminum Alloy Tempers |
| SAE AMS2355L | Quality Assurance, Sampling and Testing Aluminum Alloys and Magnesium Alloy Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded Rings |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.