SAE AMS 5662 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 52.5NI - 19CR - 3.0MO - 5.1CB (NB) - 0.90TI - 0.50AI - 18FE CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 1775 DEGREES F (968 DEGREES C) SOLUTION HEAT TREATED, PRECIPITATION-HARDENABLE
Hardcopy , PDF
20-08-2022
English
21-06-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 ACKNOWLEDGEMENT
7 REJECTIONS
8 NOTES
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings, or heading 10.00 inches (254 mm) and under in nominal diameter or least distance between parallel sides, having a maximum cross-sectional area of 78 in2(503 cm2), and forging stock of any size (see 8.5).
| Committee |
AMS F
|
| DocumentType |
Revision
|
| Pages |
10
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| 17/30369678 DC : 0 | PREN 7010 - AEROSPACE SERIES - USER GUIDE FOR CREATION AND DESIGNATION OF BOLTS |
| SAE AS 4877 : 2017 | BOLTS AND SCREWS, NICKEL ALLOY UNS N07718, CLASSIFICATION: 185 KSI/1200 DEGREES F, PROCUREMENT SPECIFICATION |
| MIL-B-85667-6 Revision A:1991 | BOLT, SLEEVE, 100 DEGREES REDUCED FLUSH HEAD, STRAIGHT SHANK, CRES 304 SLEEVE, NICKEL ALLOY 718 PIN, 125 KSI FSU, 450 DEGREES F |
| SAE AS 4723 : 2012 | INSERT, SCREW THREAD, SELF-LOCKING, UNS S66286, KEY LOCKED, PLASTIC SELF LOCKING DEVICE, SOLID FILM LUBRICANT, PROCUREMENT SPECIFICATION FOR |
| MIL-S-45909 Revision C:1989 | STUD, LOCKED IN - RING LOCKED SERRATED |
| MIL-B-23964 Revision D:1981 | BOLT, SELF-RETAINING, POSITIVE LOCKING |
| DEFSTAN 02-862(PT1)/3(2011) : 2011 | NAVAL FASTENERS - PART 1: MATERIAL SELECTION AND USE |
| SAE AMS 2774 : 2016 | HEAT TREATMENT, WROUGHT NICKEL ALLOY AND COBALT ALLOY PARTS |
| 10/30227763 DC : 0 | BS EN 6114 - AEROSPACE SERIES - BOLT, COUNTERSUNK HEAD, SHORT THREAD - INCH SERIES |
| SAE MA 3377 : 2018 | BOLTS AND SCREWS, NICKEL ALLOY UNS N07718, TENSILE STRENGTH 1275 MPA PROCUREMENT SPECIFICATION, METRIC |
| SAEITC TS149-2 | TS149 Technical Specification for All Metal Self-Locking Nuts (UNJ Threads) 1550 MPa (225,000 lbf/in²) Minimum Tensile Strength at Ambient Temperature |
| 10/30227764 DC : 0 | BS EN 6115 - AEROSPACE SERIES - BOLT - PROTRUDING HEAD, SHORT THREAD - INCH SERIES |
| SAE AS 5270 : 2013 | BOLTS, SCREWS AND STUDS, NICKEL ALLOY, UNS N07718, WORK-STRENGTHENED, TENSILE STRENGTH 220 KSI, PROCUREMENT SPECIFICATION |
| SAE AS 45909 : 2015 | STUD, LOCKED IN, RING LOCKED, SERRATED, GENERAL SPECIFICATION FOR |
| DOD-S-63275 Revision A:1982 | STUD, SCREW THREAD, LOCKED IN, RING LOCKED, SERRATED, METRIC AND RING LOCK SERRATED METRIC, GENERAL SPECIFICATION FOR |
| MIL-STD-1891 Base Document:1992 | BOLTS AND SCREWS, INSPECTION OF |
| SAE AS 1576 : 2016 | FITTINGS, WELDED, HYDRAULIC, TITANIUM, CORROSION RESISTANT STEEL AND NICKEL, 3000 PSI HYDRAULIC |
| SAE AS 7466 : 2014 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, FATIGUE RATED, PROCUREMENT SPECIFICATION |
| SAE AS 7467 : 2013 | BOLTS AND SCREWS, NICKEL ALLOY, UNS N07718, TENSILE STRENGTH 185 KSI, STRESS RUPTURE RATED, PROCUREMENT SPECIFICATION |
| SAE AMS 7466 : 1993 | BOLTS AND SCREWS - NICKEL ALLOY, CORROSION AND HEAT RESISTANT, UPSET HEADED, ROLL THREADED, FATIGUE RESISTANT |
| SAE AS 269J:2012:(S2018) | IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS |
| SAE AS 1424 : 2014 | HOSE ASSEMBLIES, METAL, MEDIUM PRESSURE, HIGH TEMPERATURE |
| SAE AS 3506 B: 2014(R2019) | INSERT - SCREW THREAD, THIN WALL, SELF-LOCKING UNS N07718, SILVER PLATED, CLASS: 185 KSI/1025 DEGREES F, PROCUREMENT SPECIFICATION |
| SAE AMS 2269 : 2006 | CHEMICAL CHECK ANALYSIS LIMITS, NICKEL, NICKEL ALLOYS, AND COBALT ALLOYS |
| SAE AMS 2806D : 2013 | IDENTIFICATION BARS, WIRE, MECHANICAL TUBING, AND EXTRUSIONS, CARBON AND ALLOY STEELS AND CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS |
| ASTM E 10 : 2017-05 | TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS |
| SAE AMS 2750 : 2012 | PYROMETRY |
| SAE AMS 2371 : 2016 | QUALITY ASSURANCE SAMPLING AND TESTING, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, WROUGHT PRODUCTS AND FORGING STOCK |
| SAE ARP 1917 : 2002 | CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS |
| SAE AMS 2374 : 2016 | QUALITY ASSURANCE SAMPLING AND TESTING CORROSION AND HEAT-RESISTANT STEEL AND ALLOY FORGINGS |
| SAE AS 6279 : 2016 | STANDARD PRACTICE FOR PRODUCTION, DISTRIBUTION, AND PROCUREMENT OF METAL STOCK |
| ASTM E 103 : 2017 : REDLINE | Standard Practice for Rapid Indentation Hardness Testing of Metallic Materials |
| SAE AMS 2261 : 2012 | TOLERANCES, NICKEL, NICKEL ALLOY, AND COBALT ALLOY BARS, RODS, AND WIRE |
| SAE AMS 2808 : 2017 | IDENTIFICATION FORGINGS |
| SAE ARP 1313 : 2014 | DETERMINATION OF TRACE ELEMENTS IN HIGH TEMPERATURE ALLOYS |
| SAE AMS7490Q | RINGS, FLASH WELDED, CORROSION AND HEAT-RESISTANT AUSTENITIC STEELS, AUSTENITIC-TYPE IRON, NICKEL, OR COBALT ALLOYS, OR PRECIPITATION-HARDENABLE ALLOYS |
| ASTM E 354 : 2014 : REDLINE | Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.