SAE AMS 3058 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GREASE: WIDE TEMPERATURE RANGE LITHIUM OR LITHIUM COMPLEX THICKENED FOR AIRCRAFT WHEEL BEARINGS
Hardcopy , PDF
09-08-2018
English
28-03-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALIFICATION
5. QUALITY ASSURANCE PROVISIONS
6. PREPARATION FOR DELIVERY
7. ACKNOWLEDGMENT
8. REJECTIONS
9. NOTES
APPENDIX A
Specifies grease for use on aircraft wheel bearings.
| Committee |
AMS-M
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IP 71 : 1995 | SECTION 1: PETROLEUM PRODUCTS - TRANSPARENT AND OPAQUE LIQUIDS - DETERMINATION OF KINEMATIC VISCOSITY AND CALCULATION OF DYNAMIC VISCOSITY - SECTION 2: GLASS CAPILLARY KINEMATIC VISCOMETERS - SPECIFICATIONS AND OPERATING INSTRUCTIONS (TWO PART SET) |
| ASTM D 566 : 2017 : REDLINE | Standard Test Method for Dropping Point of Lubricating Grease |
| DEFSTAN 05-50(PT62)/1(1995) : 1995 | METHODS FOR TESTING FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS - PART 62: LOW TEMPERATURE TORQUE OF GREASES CONTAMINATED WITH WATER |
| ASTM D 5706 : 2016 : REDLINE | Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using a High-Frequency, Linear-Oscillation (SRV) Test Machine |
| IP 132 : 96(R2004) | PETROLEUM PRODUCTS - LUBRICATING GREASE - DETERMINATION OF DROPPING POINT |
| ASTM D 942 : 2015 : REDLINE | Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method |
| ISO 2160:1998 | Petroleum products Corrosiveness to copper Copper strip test |
| ASTM D 6184 : 2017 : REDLINE | Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method) |
| DEFSTAN 05-50(PT9)/1(1986) : 1986 | METHODS FOR TESTING FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS - PART 9: SEPARATION OF OIL FROM GREASE |
| SAE AMS 4640 : 2011 | ALUMINUM BRONZE, BARS, RODS, SHAPES, TUBES, AND FORGINGS, 81.5CU - 10.0AL - 4.8NI - 3.0FE, DRAWN AND STRESS RELIEVED (HR50) OR TEMPER ANNEALED (TQ50) |
| ASTM D 5707 : 2016 : REDLINE | Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine |
| ASTM D 217 : 2017 : REDLINE | TEST METHODS FOR CONE PENETRATION OF LUBRICATING GREASE |
| ASTM D 4048 : 2017-01 | TEST METHOD FOR DETECTION OF COPPER CORROSION FROM LUBRICATING GREASE |
| ASTM D 4289 : 2014-02 | TEST METHOD FOR ELASTOMER COMPATIBILITY OF LUBRICATING GREASES AND FLUIDS |
| SAE AMS 3217/2 : 2012 | TEST SLABS, ACRYLONITRILE BUTADIENE (NBR-L), LOW ACRYLONITRILE, 65-75 |
| ASTM D 2595 : 2017 | Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range |
| FED-STD-791 Revision D:2007 | TESTING METHOD OF LUBRICANTS, LIQUID FUELS, AND RELATED PRODUCTS |
| ISO 2176:1995 | Petroleum products — Lubricating grease — Determination of dropping point |
| ASTM D 2265 : 2015-05 | TEST METHOD FOR DROPPING POINT OF LUBRICATING GREASE OVER WIDE TEMPERATURE RANGE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.