ONORM EN 1555-5 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
07-01-2022
12-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Fitness for purpose
4.1 Method of preparation of assemblies for testing
4.1.1 General
4.1.2 Butt fusion joints
4.1.3 Electrofusion jointing
4.1.4 Mechanical joints
4.2 Requirements for fitness for purpose
4.2.1 Fitness for purpose for butt fusion joints
4.2.2 Fitness for purpose for electrofusion joints
4.2.3 Fitness for purpose for mechanical joints
5 Overall service (design) coefficient
Annex A (informative) Derating coefficients for operating
temperatures
Annex B (informative) Rapid crack propagation (RCP) resistance
at temperature less than 0 degree C
Bibliography
Describes requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It also provides the definitions of electrofusion, butt fusion and mechanical joints.
| Committee |
TC 005
|
| DevelopmentNote |
Supersedes ONORM B 5192. (01/2005)
|
| DocumentType |
Standard
|
| PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNI EN 1555-5 : 2011 | Identical |
| UNE-EN 1555-5:2011 | Identical |
| I.S. EN 1555-5:2010 | Identical |
| EN 1555-5:2010 | Identical |
| SN EN 1555-5 : 2010 | Identical |
| BS EN 1555-5:2010 | Identical |
| NS EN 1555-5 : 1ED 2010 | Identical |
| NBN EN 1555-5 : 2010 | Identical |
| NF EN 1555-5 : 2010 | Identical |
| NEN EN 1555-5 : 2010 | Identical |
| DIN EN 1555-5:2010-12 | Identical |
| ONORM EN 1555-3 : 2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
| ONORM EN 15001-1 : 2011 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| ONORM EN 1555-4 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES |
| ONORM EN 1555-1 : 2015 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| ONORM EN 1555-2 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 10838-3:2001 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ONORM EN 1555-2 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ONORM EN 1555-3 : 2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
| ONORM EN 1555-1 : 2015 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 13955:1997 | Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.