
MIL-STD-2003-3 Revision A:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by

Electric Plant Installation Standard Methods for Surface Ships and Submarines (Penetrations)
English
03-09-2009
06-10-2020
1. SCOPE
2. APPLICABLE DOCUMENTS
3. DEFINITIONS
4. GENERAL REQUIREMENTS
5. DETAILED REQUIREMENTS
6. NOTES
APPENDIX A - Penetrations - Stuffing Tubes, Submarines
APPENDIX B - Penetrations - Stuffing Tubes, Surface Ships
APPENDIX C - Penetrations - Stuffing Tubes, General
APPENDIX D - Penetrations - Kickpipes
APPENDIX E - Penetrations - Pressure Hulls, Submarines
Describes standard methods for swage tubes, stuffing tubes, and kickpipes on surface ships and submarines.
DevelopmentNote |
Supersedes DOD STD 2003/3. (09/2009)
|
DocumentType |
Standard
|
Pages |
198
|
PublisherName |
US Military Specs/Standards/Handbooks
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
This standard covers standard methods for all types of electrical penetrations, including, but not restricted to, swage tubes, stuffing tubes, kickpipes, and multiple cable penetrations on surface ships and submarines.
MIL-STD-2003-1 Revision A:2009 | Electric Plant Installation Standard Methods for Surface Ships and Submarines (Cable) |
MIL-STD-2003-2 Revision A:2009 | Electric Plant Installation Standard Methods for Surface Ships and Submarines (Equipment) |
MIL-STD-2003-4 Revision A:2009 | Electric Plant Installation Standard Methods for Surface Ships and Submarines (Cableways) |
MIL-STD-2003 Revision A:2009 | Electric Plant Installation Standard Methods for Surface Ships and Submarines |
MIL-STD-2042-3 Revision C:2016 | Fiber Optic Cable Topology Installation Standard Methodsfor Surface Ships and Submarines(Cable Penetrations) (Part 3of 7 Parts) |
SAE AMSDTL23053/5A | Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Flexible, Crosslinked |
MIL P 24705 : A | PENETRATORS, MULTIPLE CABLE, FOR ELECTRICAL CABLES, GENERAL SPECIFICATION FOR |
MMM-A-121 Base Document:1966 | Adhesive, Bonding Vulcanized Synthetic Rubber to Steel |
MIL C 24231/18 : D | CONNECTOR, PLUG, MOLDED 65 CONDUCTOR |
MIL-S-24235-7 Revision B:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, for Cast Enclosures, Pressureproof |
SAE AMSS8802D | Sealing Compound, Fuel Resistant, Integral Fuel Tanks and Fuel Cell Cavities |
ASTM D 710 : 2013 : REDLINE | Standard Specification for Vulcanized Fibre Sheets, Rods, and Tubes Used for Electrical Insulation |
ASTM A 1008/A1008M : 2016-09 | SPECIFICATION FOR STEEL, SHEET, COLD-ROLLED, CARBON, STRUCTURAL, HIGH-STRENGTH LOW-ALLOY, HIGH-STRENGTH LOW-ALLOY WITH IMPROVED FORMABILITY, SOLUTION HARDENED, AND BAKE HARDENABLE |
MIL C 24231/4 : D | CONNECTOR, PLUG, MOLDED, 14, 24, 3O OR 4O CONDUCTOR (STRAIGHT AND 9O DEGREES) |
MIL-DTL-16685 Revision E:2009 | Packing, Material and Packing Preformed (Stuffing Tube for Electric Cables) |
MIL-DTL-24640 Revision C:2011 | Cables, Lightweight, Low Smoke, Electric, for Shipboard Use, General Specification for |
MIL-P-24338 Revision A:1985 | Pipe, Carbon Steel, Seamless |
MIL E 917 : E | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS (NAVAL SHIPBOARD USE) |
MIL-S-24235-18 Revision A:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Swage Type, Reduced Diameter, Steel and Aluminum, for Deck and Bulkheads with Pipe Protection |
MIL-I-3064 Revision B:1982 | Insulation, Electrical, Plastic-Sealer |
SAE AMSG4343A | Grease, Pneumatic System |
MIL-S-24235-10 Revision B:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Steel, for Decks and Bulkheads without Pipe Protection |
MIL-S-24235-19 Revision A:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Sealing Plug for Unused Stuffing Tubes |
SAE AMSWWT700/6C | Tube, Aluminum Alloy, Drawn, Seamless, 6061 |
SAE AMSP83461 | Packing, Preformed, Petroleum Hydraulic Fluid Resistant, Improved Performance at 275°F (135°C) |
MIL-PRF-15624 Revision H:2016 | Gasket Material, Rubber, 50 Durometer Hardness (Maximum) |
NASM25027:2012 | NUT, SELF-LOCKING, 250 DEGREES F, 450 DEGREES F, AND 800 DEGREES F |
MIL C 24231/1 : D | CONNECTOR, PLUG, MOLDED, THREE, FOUR, AND FIVE CONDUCTOR |
ASTM B 169/B169M : 2015 : REDLINE | Standard Specification for Aluminum Bronze Sheet, Strip, and Rolled Bar |
MIL-STD-2003 Revision A:2009 | Electric Plant Installation Standard Methods for Surface Ships and Submarines |
MIL-S-24235-1 Revision F:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Bulkhead, Pressureproof |
MIL-I-24768-1 Base Document:1992 | Insulation, Plastic, Laminated, Thermosetting, Glass-Cloth, Melamine-Resin (GME) |
A-A-59588 Revision B:2012 | Rubber, Silicone |
MIL-DTL-2726-68 Revision D:2005 | Receptacle, Plug, Connector, Electrical, 10-Ampere, 125-Volt, 3-Phase, Grounded (Symbol No. 706.1) |
MIL-S-24235-16 Revision B:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Cable, Shearing Valve, Hull, Pressureproof, Symbols 512, 512.1, 513, and 513.1 |
MIL-STD-2003-4 Revision A:2009 | Electric Plant Installation Standard Methods for Surface Ships and Submarines (Cableways) |
MIL-S-24235-14 Revision C:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, for Sheet Metal Enclosures |
MIL C 24231/3 : D | CONNECTOR, PLUG, MOLDED, SEVEN AND NINE CONDUCTOR (STRAIGHT AND 9O DEGREES) |
NAVSEA S9074 AR GIB 010/278 : 0 | REQUIREMENTS FOR FABRICATION WELDING AND INSPECTION, AND CASTING INSPECTION AND REPAIR FOR MACHINERY, PIPING, AND PRESSURE VESSELS |
MIL-S-24235-5 Revision A:1989 | Stuffing Tubes, and Packing Assemblies for Electric Cables, Ballast Tank |
MIL-S-24235-9 Revision E:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Brass and Steel, for Decks and Bulkheads with Pipe Protection |
ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
SAE AMSDTL23053/18A | Insulation Sleeving, Electrical, Heat Shrinkable, Modified Fluoropolymer, Crosslinked |
MIL-S-24235-3 Revision A:1989 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Bulkhead, for Ballast Tanks |
NAVSEA T9074 AD GIB 010/1688 : 0 | REQUIREMENTS FOR FABRICATION, WELDING AND INSPECTION OF SUBMARINE STRUCTURE |
ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
SAE AS8660 | Silicone Compound NATO Code Number S-736 |
MIL-STD-1689 Revision A:1990 | FABRICATION, WELDING, AND INSPECTION OF SHIPS STRUCTURE |
A-A-3041 Revision A:2003 | Wrench, Open End, Ratchet (Tac Pattern) for Tube Fittings, Electrical Cable Terminals, and Stuffing Tube Gland Nuts |
MIL-DTL-24643 Revision C:2009 | Cables, Electric, Low Smoke, Halogen-Free, for Shipboard Use, General Specification for |
MIL-S-24235-8 Revision B:1992 | Stuffing Tubes, Metal and Packing Assemblies for Electric Cables, for Sheet Metal Enclosures, Pressureproof |
MIL-DTL-915 Revision G:2002 | Cable, Electrical, for Shipboard Use, General Specification for |
MIL-PRF-8516 Revision G:1997 | Sealing Compound, Synthetic Rubber, Electric Connectors and Electric Systems, Chemically Cured |
ASTM B21/B 21M : 2014-10 | SPECIFICATION FOR NAVAL BRASS ROD, BAR, AND SHAPES |
MIL C 24231 : D | CONNECTOR, PLUGS, RECEPTACLES, ADAPTORS, HULL INSERTS AND HULL INSERT PLUGS, PRESSURE-PROOF, GENERAL SPECIFICATION FOR |
MIL-S-24235-17 Revision B:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, Swage Type, Steel and Aluminium, for Deck and Bulkheads with Pipe Protection |
SAE AMSP5516 | Packing, Preformed, Petroleum Hydraulic Fluid Resistant, 160°F |
MIL-I-24391 Revision C:1990 | Insulation Tape, Electrical, Plastic, Pressure-Sensitive |
MIL-S-24235 Revision C:1992 | Stuffing Tubes, Metal, and Packing Assemblies for Electric Cables, General Specification for |
MIL S 24235/2 : C | STUFFING TUBES, METAL AND PACKING ASSEMBLIES FOR ELECTRIC CABLES, PACKING ASSEMBLIES FOR PRESSUREPROOF BULKHEAD |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.