MIL-DTL-52525 Revision F:2008
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
FITTINGS, HOSE, HYDRAULIC, REUSABLE, FIELD-ATTACHABLE AND CLAMP-HALVES, TO MATE WITH SAE-J517 TYPE HOSES, GENERAL SPECIFICATION FOR
Available format(s)
PDF
Superseded date
21-04-2021
Publisher
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
Specifies fittings, hose, reusable, field attachable and clamp-halves, to mate with SAE-J517 type hoses, general specification for.
| Committee |
FSC 4730
|
| DevelopmentNote |
Supersedes MIL F 52525. (04/2004)
|
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| Supersedes |
| MIL-DTL-52471-10 Revision B:2008 | Hose Assemblies, Rubber, Hydraulic Pressure-Type, Type 100R12 Four-Spiral-Wrap Reinforcement Hose |
| MIL-DTL-52525-35 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 4-BOLT SPLIT-FLANGE, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-10 Revision D:2011 | Fittings, Hose, Screw-on to 4-Bolt Split-Flange, Straight |
| MIL-DTL-52525-32 Revision A:2008 | FITTINGS, HOSE, REINFORCED HYDRAULIC HOSE AND CLAMP-HALVES: FIELD ATTACHABLE (REUSABLE), SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, 45 DEGREES BENT TUBE, FOR USE WITH TYPE 100RE FOUR-SPIRAL-WRAP REINFORCEMENT HOSE |
| MIL-DTL-52525-44 Base Document:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-1 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, Straight, SAE-J516 Type, for Assembly with SAE-J517, Type 100R2 Hose |
| MIL-DTL-52525-43 Base Document:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, STRAIGHT |
| MIL-DTL-52525-11 Revision C:2008 | Fittings, Hose, Screw-On to 4-Bolt Split-Flange, 45 Degree Bent Tube |
| MIL-DTL-52525-38 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, 45 DEGREES BENT TUBE |
| MIL-DTL-52471-1 Revision C:2008 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC PRESSURE-TYPE, TYPE 100R1, SINGLE-WIRE BRAIDED REINFORCEMENT HOSE |
| MIL-DTL-52525-6 Revision C:2008 | Fittings,Hose, Screw-on to 37 Degree Flare Female Swivel, 45Degree BentTube |
| MIL-DTL-52525-36 Revision B:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 90 DEGREES BENT TUBE |
| MIL-DTL-52525-15 Revision C:2008 | FITTINGS, HOSE, SCREW-ON TO 4-BOLT SPLIT-FLANGE, 90 DEGREES BENT TUBE |
| MIL-DTL-52525-13 Revision C:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE STRAIGHT |
| MIL-DTL-52525-5 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, Straight |
| MIL-DTL-52525-34 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 4-BOLT SPLIT-FLANGE, STRAIGHT |
| MIL-DTL-52525-2 Revision C:2008 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 45 Degree Bent Tube |
| MIL-DTL-52525-3 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 90 Degree Bent Tube, Short Drop |
| MIL-DTL-52525-9 Revision C:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, STRAIGHT |
| MIL-DTL-52525-17 Revision C:2008 | Fittings, Clamp-Halves, Flange to Port, for 4-Bolt Split-Flange |
| MIL-DTL-52525-31 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL |
| MIL-DTL-52471 Revision F:2008 | HOSE AND HOSE ASSEMBLIES, RUBBER, HYDRAULIC PRESSURE TYPE, GENERAL SPECIFICATION FOR |
| MIL-DTL-52471-8 Revision B:2008 | Hose Assemblies, Rubber: Hydraulic Pressure-Type; Type 100RE |
| MIL-DTL-52525-37 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, STRAIGHT |
| MIL-DTL-52525-16 Revision D:2008 | Fittings, Clamp-Halves, for 4-Bolt Split-Flange, SAE-J518-1or SAE-J518-2, Type Split-Flange Clamp (SFC) |
| MIL-DTL-52471-2 Revision C:2008 | HOSE ASSEMBLIES, RUBBER: HYDRAULIC PRESSURE-TYPE; TYPE 100R2, DOUBLE-WIRE BRAIDED REINFORCEMENT HOSE |
| MIL-DTL-52471-3 Revision C:2008 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC PRESSURE-TYPE, TYPE 100RE, FOUR-WIRE BRAIDED REINFORCEMENT OR MULTIPLE WIRE BRAIDED STEEL WIRE REINFORCED HOSE |
| MIL-DTL-52525-45 Base Document:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 90 DEGREES BENT TUBE |
| MIL-DTL-52525-39 Revision B:2008 | FITTINGS, HOSE, SCREW-ON TO 37DEGREES FLARE FEMALE SWIVEL, 90 DEGREES BENT TUBE |
| MIL-DTL-52525-8 Revision C:2008 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 90 DegreeBent Tube, Long Drop |
| MIL-DTL-52525-7 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degrees Flare Female Swivel, 90 Degrees Bent Tube, Short Drop |
| MIL-DTL-52525-14 Revision C:2008 | FITTINGS, HOSE CRIMP TYPE, SPLIT-FLANGE 45 DEGREES BENT |
| MIL-DTL-52525-41 Revision A:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, 45 DEGREES BENT TUBE |
| MIL-DTL-52525-42 Revision B:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE 90 DEGREES BENT |
| MIL-DTL-52525-12 Revision D:2011 | Fittings, Hose, Screw on to Split-Flange 90 Degree Bent |
| MIL-DTL-52525-33 Revision A:2008 | FITTINGS, WIRE REINFORCED HYDRAULIC HOSE AND CLAMP-HALVES: FIELD ATTACHABLE (REUSABLE), SCREW-ON TO 37 DEGREES FLARE FEMALE SWIVEL, 90 DEGREES BENT TUBE, FOR USE WITH TYPE 100RE FOUR-SPRIAL-WRAP REINFORCEMENT HOSE |
| MIL-DTL-52525-40 Revision B:2008 | FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, STRAIGHT |
| MIL-DTL-52525-4 Revision D:2011 | Fittings, Hose, Screw-on to 37 Degree Flare Female Swivel, 90 Degree Bent Tube, Long Drop |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| SAE J517_201612 | Hydraulic Hose |
| SAE AMS5645S | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated |
| SAE AMSQQA225/9A | Aluminum Alloy 7075, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished |
| SAE AS4841B | Fittings, 37° Internal Flare, Fluid Connection, Procurement Specification |
| SAE AMSQQP416E | Plating, Cadmium (Electrodeposited) |
| FED-STD-H28-8 Revision B:1992 | Screw-Thread Standards for Federal Services Section 8 Dryseal Pipe Threads |
| SAE J518_201303 | Hydraulic Flanged Tube, Pipe, and Hose Connections, Four-Bolt Split Flange Type |
| SAE AMS 2488 : 2000 | ANODIC TREATMENT - TITANIUM AND TITANIUM ALLOYS SOLUTION PH 13 OR HIGHER |
| MIL-DTL-16232 Revision G:2000 | PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE |
| SAE AS28775A | PACKING, PREFORMED - MS28775 O-RING |
| SAE J516_201604 | Hydraulic Hose Fittings |
| ANSI/NCSL Z540 3 : 2006(R2013) | REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT |
| MIL-DTL-52471-8 Revision B:2008 | Hose Assemblies, Rubber: Hydraulic Pressure-Type; Type 100RE |
| SAE AMS6382P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Annealed |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| SAE AMS5743J | Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered |
| SAE AMSQQA200/8A | Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire, Extruded A96061 |
| SAE AMSA22771C | Aluminum Alloy Forgings, Heat Treated |
| SAE AMS4141G | Aluminum Alloy Die Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution and Precipitation Heat Treated |
| SAE J403_201406 | Chemical Compositions of SAE Carbon Steels |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS5647K | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated |
| MIL-DTL-52471-3 Revision C:2008 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC PRESSURE-TYPE, TYPE 100RE, FOUR-WIRE BRAIDED REINFORCEMENT OR MULTIPLE WIRE BRAIDED STEEL WIRE REINFORCED HOSE |
| MIL-STD-889 Revision C:2016 | DISSIMILAR METALS |
| MIL-PRF-2104 Revision K:2016 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT/TACTICAL SERVICE |
| MIL-DTL-81706 Revision B:2004 | Chemical Conversion Materials for Coating Aluminum and Aluminum Alloys |
| SAE AMSQQA367D | Aluminum Alloy Forgings |
| SAE AMS2417J | Plating, Zinc-Nickel Alloy |
| ASTM B 567 : 1998 | Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method |
| SAE J343_201605 | Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies |
| SAE J515_201511 | Specification for O-Ring Materials Used with Hydraulic Connectors |
| SAE AMS2451/9B | Plating, Brush, Zinc-Nickel Low Hydrogen Embrittlement |
| SAE J514_201201 | Hydraulic Tube Fittings |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AMS4117K | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6, -T651) |
| SAE AMS4127J | Aluminum Alloy, Forgings and Rolled or Forged Rings (6061-T6) Solution and Precipitation Heat Treated |
| SAE AMS2700E | Passivation of Corrosion Resistant Steels |
| SAE AMS5639J | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated |
| SAE AMS6370P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) |
| FED-STD-162 Revision A:1967 | HOSE, RUBBER, VISUAL INSPECTION GUIDE FOR |
| ASTM A 276/A276M : 2017 : REDLINE | Standard Specification for Stainless Steel Bars and Shapes |
| SAE AMS4124E | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, T7351) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4928V | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed |
| MIL-DTL-52471 Revision F:2008 | HOSE AND HOSE ASSEMBLIES, RUBBER, HYDRAULIC PRESSURE TYPE, GENERAL SPECIFICATION FOR |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.