MIL-DTL-28754 Revision E:2016
Current
Current
The latest, up-to-date edition.
Connectors, Electrical, Modular, and Component Parts General Specification for
Available format(s)
PDF
Language(s)
English
Published date
03-05-2016
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PACKAGING
6. NOTES
APPENDIX - PROCEDURE FOR FIRST ARTICLE INSPECTION
Specifies the general requirements for backplane connectors, module connectors, cable connectors, and their component parts.
| DevelopmentNote |
Supersedes MIL C 28754 (D). (05/2016)
|
| DocumentType |
Standard
|
| Pages |
56
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Current
|
| Supersedes |
This specification covers the general requirements for backplane connectors, module connectors, cable connectors, and their component parts.
| MIL-DTL-28754-62 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER, CROSSOVER, CONTACT TAILS ON .050 CENTERS |
| MIL DTL 28754/60 : A | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS |
| MIL-DTL-28754-59 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS (CERAMIC COMPATIBLE) |
| MIL-DTL-28754-94 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR FRAME, TYPE 4, DIP, 0.4 PITCH, FORMAT C, D AND E |
| MIL-DTL-28754-61 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center, Crossover, Contact Tails on .100 Centers (Ceramic Compatible) |
| MIL-DTL-28754-67 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR FRAME, TYPE 4, DOUBLE SPAN, CENTER |
| MIL-STD-202-211 Base Document:2015 | METHOD 211, TERMINAL STRENGTH |
| SAE AMS QQ A 250/8 : 2014 | ALUMINUM ALLOY 5052, PLATE AND SHEET |
| MIL-C-28754-81 Revision A:1994 | CONNECTORS, ELECTRICAL, MODULAR, TYPE III, FEMALE CONTACT & POLARIZING BUSHING SET, LOW INSERTION FORCE (LIF), REMOVABLE WIRE WRAPPOST TERMINAL |
| SAE AMS QQ A 225/9 : 2014 | ALUMINUM ALLOY 7075, BAR, ROD, WIRE, AND SPECIAL SHAPES; ROLLED, DRAWN, OR COLD FINISHED |
| MIL-DTL-49055 Revision G:2017 | CABLES, POWER, ELECTRICAL, (FLEXIBLE, FLAT, UNSHIELDED), (ROUND CONDUCTOR), GENERAL SPECIFICATION FOR |
| SAE AMS 4115 : 2015 | ALUMINUM ALLOY, ROLLED OR COLD-FINISHED, BARS, RODS, WIRE, AND FLASH WELDED RINGS, ANNEALED, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-O) |
| SAE AMS 4027 : 2014 | ALUMINUM ALLOY, SHEET AND PLATE, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061; -T6 SHEET, -T651 PLATE), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASME Y14.5 : 2009 | DIMENSIONING AND TOLERANCING |
| MIL-DTL-45204 Revision D:2007 | Gold Plating, Electrodeposited |
| ANSI/NCSL Z540 3 : 2006(R2013) | REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT |
| MIL-DTL-28754-38 Revision E:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, CONTACT, GROUNDING, WRAPPOST |
| MIL-DTL-28754-6 Revision D:2014 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, 40 PIN, STRAIGHT THROUGH |
| MIL-STD-1130 Revision C:2012 | Connections, Electrical, Solderless Wrapped |
| ASTM A 666 : 2015 : REDLINE | Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar |
| SAE AMS 4026 : 2014 | ALUMINUM ALLOY, SHEET AND PLATE, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061; -T4 SHEET, -T451 PLATE), SOLUTION HEAT TREATED AND NATURALLY AGED |
| SAE AMS QQ A 200/8 : 2015 | ALUMINUM ALLOY 6061, BAR, ROD, SHAPES, TUBE, AND WIRE, EXTRUDED A96061 |
| SAE AMS QQ N 290 : 2015 | NICKEL PLATING (ELECTRODEPOSITED) |
| ASTM A 693 : 2016 : REDLINE | Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS 4116 : 2015 | ALUMINUM ALLOY, BARS, RODS, AND WIRE, 1.0MG - 0.60SI - 0.30CU - 0.20CR (6061-T4), COLD FINISHED, SOLUTION HEAT TREATED AND NATURALLY AGED |
| MIL-DTL-28754-21 Revision F:2014 | Connectors, Electrical, Modular, Frame, Casting, Type IV, Double Span |
| MIL-C-28754-80 Revision A:1994 | CONNECTORS, ELECTRICAL, MODULAR, TYPE III, FEMALE CONTACT & GROUND BUSHING SET, LOW INSERTION FORCE (LIF), REMOVABLE WIRE WRAPPOST TERMINAL |
| ASTM B 121/B121M : 2016 : REDLINE | Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar |
| MIL-STD-889 Revision C:2016 | DISSIMILAR METALS |
| MIL-DTL-14072 Revision F:2013 | FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| MIL-DTL-28754-39 Revision D:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, KEYING PEGS |
| SAE AMS QQ S 763D : 2013(S2015) | STEEL, CORROSION RESISTANT, BARS, WIRE, SHAPES, AND FORGINGS |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| MIL-DTL-16878 Revision H:2012 | WIRE, ELECTRICAL, INSULATED, GENERAL SPECIFICATION FOR |
| SAE AMSSTD595A:2017 | COLORS USED IN GOVERNMENT PROCUREMENT |
| MIL-DTL-28754-35 Revision F:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, MALE CONTACT AND INSULATOR BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL |
| SAE AMS 4025 : 2014 | ALUMINUM ALLOY, SHEET AND PLATE, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-O) ANNEALED |
| MIL-DTL-28754-34 Revision E:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND INSULATOR BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AMS 4117 : 2015 | ALUMINUM ALLOY, ROLLED OR COLD FINISHED BARS, RODS, AND WIRE AND FLASH WELDED RINGS, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061; -T6, -T651) |
| SAE AMS QQ A591 : 2014 | ALUMINUM ALLOY DIE CASTINGS |
| MIL-C-28754-79 Revision A:1994 | CONNECTORS, ELECTRICAL, MODULAR, TYPE III, FEMALE CONTACT & INSULATOR BUSHING SET, LOW INSERTION FORCE (LIF), REMOVABLE WIRE WRAPPOST TERMINAL |
| A-A-56032 Revision D:2003 | INK, MARKING, EPOXY BASE |
| SAE AS 81044 : 2011 | WIRE, ELECTRICAL, CROSSLINKED POLYALKENE, CROSSLINKED ALKANE-IMIDE POLYMER, OR POLYARLYENE INSULATED, COPPER OR COPPER ALLOY |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| MIL-DTL-55330 Revision C:2001 | CONNECTORS, ELECTRICAL AND FIBER OPTIC, PACKAGING OF |
| ASTM B 194 : 2015 : REDLINE | Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
| SAE AMS 2700E : 2011 | PASSIVATION OF CORROSION RESISTANT STEELS |
| MIL-DTL-28754-36 Revision E:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND GROUNDING BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL |
| L-P-410 Revision A:1966 | PLASTIC, POLYAMIDE (NYLON), RIGID: RODS, TUBES, FLATS, MOLDED AND CAST PARTS |
| MIL-STD-202-105 Base Document:2015 | Method 105, Barometric Pressure (Reduced) |
| MIL-STD-202-208 Base Document:2015 | Method 208, Solderability |
| MIL-DTL-28754-37 Revision E:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND POLARIZING BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL |
| MIL-STD-202 Revision H:2015 | ELECTRONIC AND ELECTRICAL COMPONENT PARTS |
| SAE AMS 4128 : 2013 | ALUMINUM ALLOY BARS, ROLLED OR COLD FINISHED, 1.0MG - 0.60SI - 0.30CU - 0.20CR (6061-T451), SOLUTION HEAT TREATED AND STRESS RELIEVED BY STRETCHING |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| MIL-STD-1285 Revision D:2004 | MARKING OF ELECTRICAL AND ELECTRONIC PARTS |
| MIL-DTL-28754-31 Revision D:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR ASSEMBLY, TYPE 5, 40-PIN, TWO PIECE INSERT, AND 20-PIN, ONE HALF, ONE PIECE INSERT |
| SAE AMS QQ A 225/6 : 1998 | ALUMINUM ALLOY, 2024, BAR, ROD, AND WIRE; ROLLED, DRAWN, OR COLD FINISHED |
| FED-STD-H28 Revision A:1994 | Screw-Thread Standards for Federal Services |
| EIA 557 : 2006 | STATISTICAL PROCESS CONTROL SYSTEMS |
| ASTM B 928/B928M : 2015 : REDLINE | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| MIL C 28754/67 : 0 | CONNECTOR, ELECTRICAL, MODULAR, CONNECTOR FRAME, TYPE 4, DOUBLE SPAN, CENTER |
| ASTM D 1867 : 2013 : REDLINE | Standard Specification for Copper-Clad Thermosetting Laminates for Printed Wiring |
| ASTM B 122/B122M : 2016 : REDLINE | Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.