ISO 3007:1999
Current
The latest, up-to-date edition.
Petroleum products and crude petroleum — Determination of vapour pressure — Reid method
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
English, French
14-10-1999
This International Standard specifies a method for the determination of the vapour pressure of liquid petroleum
products consisting of essentially or wholly of hydrocarbon components, or containing oxygenated hydrocarbons of
specific types and at specified maximum concentrations. The method does not apply outside these concentration
levels, nor to any blends containing methanol or other oxygenated hydrocarbons not covered in note 1.
NOTE 1 The maximum concentration of ethers containing 5 or more carbon atoms is 15 % (V/V), and for ethanol is 10 %
(V/V). For higher alcohols, the maximum concentration is 7 % (V/V).
NOTE 2 For the purposes of this International Standard, the term "%(V/V)" is used to represent the volume fraction of a
material.
For petroleum products containing methanol, or other oxygenated hydrocarbons outside the scope of note 1, a dry
vapour-pressure test method should be used. For liquefied petroleum gases, ISO 4256 should be used. The test
method may be applied to volatile crude petroleum with a vapour pressure exceeding 10 kPa, although the
precision has not been evaluated.
Four procedures are described in this International Standard. Procedures A and B are alternative apparatus
configurations for products with a Reid vapour pressure up to 180 kPa, Procedure C is applied to liquid products
with a Reid vapour pressure above 180 kPa, and Procedure D applies to aviation gasolines with a Reid vapour
pressure of approximately 50 kPa.
Vapour pressure is an important physical property of volatile liquids, and has critical performance implications for
automotive and aviation gasolines. Vapour pressure is also one of the properties affecting atmospheric evaporation,
and is therefore increasingly used in regulations relating to emissions and air quality control. Vapour pressure is
also a critical property limiting the performance and safety of operation of equipment during transfer operations.
NOTE Because the external atmospheric pressure is counteracted by the atmospheric pressure initially in the vapour
chamber, the Reid vapour pressure is approximately the "absolute" vapour pressure at 37,8 °C. The Reid vapour pressure
differs from the true vapour pressure of the sample owing to slight vaporization of the sample and the pressure of water vapour
and air in the confined space.
DocumentType |
Standard
|
Pages |
17
|
PublisherName |
International Organization for Standardization
|
Status |
Current
|
Supersedes |
Standards | Relationship |
BIS IS 1448-39 : 2012 | Identical |
NEN ISO 3007 : 1999 | Identical |
BS ISO 3007:1999 | Identical |
NBN EN-12 : 1994 | Identical |
BS 2000-69(2001) : 2001 | Identical |
NFM 07 007 : 1969 | Similar to |
13/30279896 DC : 0 | BS ISO 8178-5 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 5: TEST FUELS |
11/30227325 DC : 0 | BS ISO 4164 - MOPEDS - ENGINE TEST CODE - NET POWER |
BS EN ISO 10416:2009 | Petroleum and natural gas industries. Drilling fluids. Laboratory testing |
I.S. EN ISO 10416:2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING FLUIDS - LABORATORY TESTING |
BS ISO 8178-5:2008 | Reciprocating internal combustion engines. Exhaust emission measurement Test fuels |
ISO 8178-6:2000 | Reciprocating internal combustion engines Exhaust emission measurement Part 6: Report of measuring results and test |
BS EN ISO 3838:2004 | Methods of test for petroleum and its products. BS 2000-189/190. Crude petroleum and liquid or solid petroleum products. Determination of density or relative density. Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods |
11/30227322 DC : 0 | BS ISO 4106 - MOTORCYCLES - ENGINE TEST CODE - NET POWER |
05/30143111 DC : DRAFT DEC 2005 | EN 13016-1 - LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) |
BS ISO 4164:2012 | Mopeds. Engine test code. Net power |
BS 2000-365(1996) : 1996 | METHOD OF TEST FOR PETROLEUM AND ITS PRODUCTS - CRUDE PETROLEUM AND PETROLEUM PRODUCTS - DETERMINATION OF DENSITY - OSCILLATING U-TUBE METHOD |
ISO 6460-1:2007 | Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 1: General test requirements |
ISO 4256:1996 | Liquefied petroleum gases — Determination of gauge vapour pressure — LPG method |
ISO 12185:1996 | Crude petroleum and petroleum products — Determination of density — Oscillating U-tube method |
ISO 3838:2004 | Crude petroleum and liquid or solid petroleum products Determination of density or relative density Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods |
I.S. EN ISO 13734:2013 | NATURAL GAS - ORGANIC COMPONENTS USED AS ODORANTS - REQUIREMENTS AND TEST METHODS (ISO 13734:2013) |
I.S. EN ISO 3838:2004 | CRUDE PETROLEUM AND LIQUID OR SOLID PETROLEUM PRODUCTS - DETERMINATION OF DENSITY OR RELATIVE DENSITY - CAPILLARY STOPPERED PYCNOMETER AND GRADUATED BICAPILLARY PYCNOMETER METHODS |
I.S. EN ISO 3170:2004 | PETROLEUM LIQUIDS - MANUAL SAMPLING |
I.S. EN ISO 8178-5:1998 | RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 5: TEST FUELS |
VDI 3479:2010-08 | Emission control - Marketing installation tank farms |
BS 2000-189.190(2004) : 2004 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - BS 2000-189/190 - CRUDE PETROLEUM AND LIQUID OR SOLID PETROLEUM PRODUCTS - DETERMINATION OF DENSITY OR RELATIVE DENSITY - CAPILLARY-STOPPERED PYKNOMETER AND GRADUATED BICAPILLARY PYKNOMETER METHODS |
17/30352956 DC : 0 | BS ISO 8178-6 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 6: REPORT OF MEASURING RESULTS AND TEST |
BS ISO 10416 : 2008 | PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING FLUIDS - LABORATORY TESTING |
BS 2000-270(1996) : 1996 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - PETROLEUM PRODUCTS - DETERMINATION OF LEAD CONTENT OF GASOLINE - IODINE MONOCHLORIDE METHOD |
BS ISO 6460-1 : 2007 | MOTORCYCLES - MEASUREMENT METHOD FOR GASEOUS EXHAUST EMISSIONS AND FUEL CONSUMPTION - PART 1: GENERAL TEST REQUIREMENTS |
EN 13016-1:2018 | Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE) |
I.S. EN 13016-1:2007 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) |
ISO 8178-5:2015 | Reciprocating internal combustion engines Exhaust emission measurement Part 5: Test fuels |
DIN EN ISO 13734:2014-03 | Natural gas - Organic components used as odorants - Requirements and test methods (ISO 13734:2013) |
DIN EN ISO 3838:2004-09 | Crude petroleum and liquid or solid petroleum products - Determination of density or relative density - Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods (ISO 3838:2004) |
UNE-EN ISO 13734:2014 | Natural gas - Organic components used as odorants - Requirements and test methods (ISO 13734:2013) |
EN ISO 8178-5 : 1997 | RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - TEST FUELS |
UNI EN ISO 13734 : 2014 | NATURAL GAS - ORGANIC COMPONENTS USED AS ODORANTS - REQUIREMENTS AND TEST METHODS |
BS 4714:1980 | Method for laboratory determination of density or relative density of crude petroleum and liquid petroleum products (hydrometer method) |
DIN EN 13016-1:2007-11 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT |
BS 4699(1985) : 85 AMD 8893 | METHODS FOR DETERMINATION OF DENSITY OR RELATIVE DENSITY OF PETROLEUM AND PETROLEUM PRODUCTS (PYKNOMETER METHODS) |
ISO 4106:2012 | Motorcycles — Engine test code — Net power |
BS ISO 4106:2012 | Motorcycles. Engine test code. Net power |
BS ISO 8178-6:2000 | Reciprocating internal combustion engines. Exhaust emission measurement Report of measuring results and test |
BS 2000-160(1998) : 1998 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - BS 2000-160: CRUDE PETROLEUM AND LIQUID PETROLEUM PRODUCTS - LABORATORY DETERMINATION OF DENSITY - HYDROMETER METHOD |
API 13I REDLINE : 2009 | RECOMMENDED PRACTICE FOR LABORATORY TESTING OF DRILLING FLUIDS |
BS 7392:1990 | Method for determination of distillation characteristics of petroleum products |
API 13I : 2009 : R2016 | RECOMMENDED PRACTICE FOR LABORATORY TESTING OF DRILLING FLUIDS |
10/30206562 DC : 0 | BS ISO 6855-1 - MOPEDS - MEASUREMENT METHOD FOR GASEOUS EXHAUST EMISSIONS AND FUEL CONSUMPTION - PART 1: GENERAL TEST REQUIREMENTS |
UNI EN ISO 10416 : 2010 | PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING FLUIDS - LABORATORY TESTING |
ISO 4164:2012 | Mopeds — Engine test code — Net power |
API RP 13I : 2009 | RECOMMENDED PRACTICE FOR LABORATORY TESTING OF DRILLING FLUIDS |
NF EN 13016-1 : 2007 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) |
BS EN 13016-1:2007 | Liquid petroleum products. Vapour pressure Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE) |
BS 2000-394(2007) : 2007 | LIQUID PETROLEUM PRODUCTS - VAPOUR PRESSURE - PART 1: DETERMINATION OF AIR SATURATED VAPOUR PRESSURE (ASVP) AND CALCULATED DRY VAPOUR PRESSURE EQUIVALENT (DVPE) |
DIN EN ISO 3170:2004-06 | Petroleum liquids - Manual sampling (ISO 3170:2004) |
BS EN ISO 12185:1996 | Methods of test for petroleum and its products. Crude petroleum and petroleum products. Determination of density. Oscillating U-tube method |
BS EN ISO 3675:1998 | Crude petroleum and liquid petroleum products. Laboratory determination of density. Hydrometer method |
ISO 3170:2004 | Petroleum liquids — Manual sampling |
BS EN ISO 4256:1998 | Liquid petroleum products. Determination of gauge vapour pressure. LPG method |
ISO 10416:2008 | Petroleum and natural gas industries — Drilling fluids — Laboratory testing |
ISO 3830:1993 | Petroleum products Determination of lead content of gasoline Iodine monochloride method |
BS EN ISO 8178-5:1997 | Reciprocating internal combustion engines. Exhaust emission measurement Test fuels |
ISO 13734:2013 | Natural gas — Organic components used as odorants — Requirements and test methods |
EN ISO 3830:1995 | Petroleum products - Determination of lead content of gasoline - Iodine monochloride method (ISO 3830:1993) |
EN ISO 3170:2004 | Petroleum liquids - Manual sampling (ISO 3170:2004) |
EN ISO 12185:1996 | Crude petroleum and petroleum products - Determination of density - Oscillating U-tube method (ISO 12185:1996) |
EN ISO 3675:1998 | Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method (ISO 3675:1998) |
EN ISO 3838:2004 | Crude petroleum and liquid or solid petroleum products - Determination of density or relative density - Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods (ISO 3838:2004) |
EN ISO 13734:2013 | Natural gas - Organic components used as odorants - Requirements and test methods (ISO 13734:2013) |
EN ISO 4256:1998 | Liquefied petroleum gases - Determination of gauge pressure - LPG method (ISO 4256:1996) |
EN ISO 10416:2009 | Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008) |
BS 2000-69(1982) : 1982 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - REID VAPOUR PRESSURE OF PETROLEUM PRODUCTS |
BS ISO 6855-1:2012 | Mopeds. Measurement method for gaseous exhaust emissions and fuel consumption General test requirements |
NF EN ISO 10416 : 2010 | PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING FLUIDS - LABORATORY TESTING |
DEFSTAN 91-76/1(1993) : 1993 | GASOLINE AUTOMOTIVE, LEADED: CIVGAS (93 RON) |
ISO 6855-1:2012 | Mopeds — Measurement method for gaseous exhaust emissions and fuel consumption — Part 1: General test requirements |
BS 2000-475(2004) : 2004 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - BS 2000-475: PETROLEUM LIQUIDS - MANUAL SAMPLING |
BS EN ISO 3170:2004 | Methods of test for petroleum and its products. BS 2000-475: Petroleum liquids. Manual sampling |
BS EN ISO 13734:2013 | Natural gas. Organic components used as odorants. Requirements and test methods |
BS EN ISO 3830:1996 | Petroleum products. Determination of lead content of gasoline. Iodine monochloride method |
ISO 3675:1998 | Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method |
I.S. EN ISO 12185:1997 | CRUDE PETROLEUM AND PETROLEUM PRODUCTS - DETERMINATION OF DENSITY - OSCILLATING U-TUBE METHOD |
BS 3324:1980 | Method for determination of vapour pressure of liquefied petroleum gases (LPG method) |
ISO 3170:2004 | Petroleum liquids — Manual sampling |
ISO 4256:1996 | Liquefied petroleum gases — Determination of gauge vapour pressure — LPG method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.