ISO 1183:1987
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Plastics Methods for determining the density and relative density of non-cellular plastics
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Withdrawn date
09-04-2019
Superseded by
ISO 1183-1:2004
ISO 1183-3:1999
ISO 1183-2:2004
ISO 1183-1:2012
Language(s)
English, French
Published date
09-07-1987
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Specification of four methods for the determination of the density of plastics except cellular plastics. Method A: Immersion method for plastics in a finished condition; Method B: Pyknometer method for plastics in the form of small particles such as powders, granules pellets or flakes; Method C: Titration method for plastics in forms as required for method A including pellets; Method D: Density gradient column method, particularly suited to measurements of small samples of products and to comparison of densities.
| DevelopmentNote |
BS DRAFT 96/124127 DC REFERS TO A REVISION BS draft 98/122556 DC refers to a new revision. (01/2002)
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BIS IS 13360-3-1 : 1995(R2003) | Identical |
| BS 3715:1964 | Similar to |
| UNE 53020:1973 | Identical |
| AS 1193-1989 | Identical |
| NEN ISO 1183 : 1992 | Identical |
| NF EN 61183 : 1994 | Identical |
| NFT 54 022 : 1980 | Similar to |
| BS 2782-6:Methods 620A to 620D:1991 | Identical |
| DIN 53479:1976-07 | Identical |
| NBN T 40 102 : 1988 | Identical |
| BS 2782-6 Methods 620A to 620D:1980 | Similar to |
| 02/103631 DC : DRAFT MAY 2002 | BS EN 14471 - CHIMNEYS - REQUIREMENTS AND TEST METHODS FOR SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS |
| PREN ISO 7792-2 : DRAFT 2011 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNE-EN 50290-2-33:2016 | Communication cables - Part 2-33: Common design rules and construction - Polyethylene insulation compounds for multi element metallic cables for indoor installation (data cable) |
| 97/713393 DC : DRAFT AUG 1997 | PREN 4364 - AEROSPACE STANDARD - CAST (PMMA) ACRYLIC - PROPERTIES |
| BS 2782-3.323F(1997) : 1997 | METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - TENSILE VIBRATION - SONIC-PULSE PROPAGATION METHOD |
| 96/106185 DC : DRAFT AUG 1996 | PREN 1337-5 - STRUCTURAL BEARINGS - PART 5: POT BEARINGS |
| 10/30212123 DC : 0 | BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| ASTM D 6778 : 2014 : REDLINE | Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) |
| BS 7253-5:1990 | Non-metallic materials for surgical implants Specification for ultra-high molecular mass polyethylene in moulded form |
| 02/121749 DC : DRAFT APR 2002 | PREN 438-4 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| 11/30192003 DC : 0 | BS EN ISO 7792-2 - PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| VDE 0212-2 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| BS ISO 1872-1 : 1993 AMD 10640 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| 15/30294124 DC : 0 | BS EN 60674-2 ED 2.0 - SPECIFICATION FOR PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| 05/30091855 DC : DRAFT MAR 2005 | ISO 1874-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 10931-1:1997 | Plastics piping systems for industrial applications. Poly (vinylidene fluoride) General |
| 04/30115317 DC : 0 | BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS |
| NFC 33 009-2 : 2008 | ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERIZATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS |
| BS 7825-3.6:1997 | Calibration of rubber and plastics test equipment. Calibration schedules Dimensional properties |
| 97/713392 DC : DRAFT AUG 1997 | PREN 4243 - AEROSPACE SERIES - ACRYLIC (PMMA) SHEETS - TECHNICAL SPECIFICATION |
| BS ISO 1268-7:2001 | Fibre-reinforced plastics. Methods of producing test plates Resin transfer moulding |
| 96/709570 DC : DRAFT JUL 1996 | PREN 10285 - STEEL TUBES AND FITTINGS FOR ON AND OFFSHORE PIPELINES - EXTERNAL THREE LAYER EXTRUDED POLYETHYLENE BASED COATINGS |
| 93/706616 DC : 0 | PREN 2833-1 - AEROSPACE SERIES - TECHNICAL SPECIFICATION - GLASS FIBER THERMOSETTING PREIMPREGNATES - PART 1: GENERAL |
| PREN 4366 : 200P1 | AEROSPACE SERIES - HEAT AND CRAZING RESISTANT CAST ACRYLIC, CROSSLINKED, MULTI-AXIALLY STRETCHED, AND LOW MOISTURE ABSORPTION - PROPERTIES |
| PREN 2343 : 2 | AEROSPACE SERIES - HEAT AND CRAZING RESISTANT CAST AND MULTI-AXIALLY ORIENTATED ACRYLIC SHEETS FOR AIRCRAFT GLAZING - TECHNICAL SPECIFICATION |
| PREN 2564 : DRAFT 2017 | AEROSPACE SERIES - CARBON FIBRE LAMINATES - DETERMINATION OF THE FIBRE, RESIN AND VOID CONTENTS |
| PREN 2719 : 200P1 | AEROSPACE SERIES - POLYCARBONATE SHEET - TECHNICAL SPECIFICATION |
| PREN 3001 : 200P1 | AEROSPACE SERIES - TEMPERED FLOAT GLASS PLIES FOR AIRCRAFT APPLICATIONS - TECHNICAL SPECIFICATION |
| PREN 4243 : 200P1 | AEROSPACE SERIES - CAST ACRYLIC SHEETS - TECHNICAL SPECIFICATION |
| PREN 2833-3 : 200P1 | AEROSPACE SERIES - GLASS FIBRE THERMOSETTING PREIMPREGNATES - TECHNICAL SPECIFICATION - PART 3: GLASS FABRIC/EPOXY RESIN PREIMPREGNATE CURING AT UP 180 DEGREES C FOR CONTINUOUS USE UP TO 120 DEGREES C |
| IEC 60893-2:2003 | Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| ASTM F 944 : 1997 | Standard Specification for Properties of Adult Alpine Ski Boots (Withdrawn 2004) |
| DIN EN 2564:1998-08 | AEROSPACE SERIES - CARBON FIBRE LAMINATES - DETERMINATION OF THE FIBRE-, RESIN- AND VOID CONTENTS |
| ASTM D 6779 : 2017 : REDLINE | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 5575 : 2007 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 5577 : 1994 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics |
| ASTM D 5935 : 1996 | Practice for Acquisition and Presentation of Comparable Single-Point Data (Withdrawn 1998) |
| DIN EN 13121-1:2003-10 | GRP tanks and vessels for use above ground - Part 1: Raw materials; Specification conditions and acceptance conditions |
| DIN EN ISO 4613-2:2004-12 | PLASTICS - ETHYLENE/VINYL ACETATE (E/VAC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 14598-3:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| EN 13121-1:2003 | GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions |
| BS EN 10288:2002 | Steel tubes and fittings for onshore and offshore pipelines. External two layer extruded polyethylene based coatings |
| BS EN 13706-3:2002 | Reinforced plastics composites. Specifications for pultruded profiles Specific requirements |
| BS EN 1452-2 : 2000 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: PIPES |
| IEC 62011-2:2004 | Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| BS EN ISO 1622-2:1999 | Plastics. Polystrene (PS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 11542-2 : 1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 13677-2:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements |
| BS EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) General |
| BS EN 1456-1:2001 | Plastic piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for piping components and the system |
| BS EN 60893-2:2004 | Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Methods of test |
| BS EN ISO 2580-2:2003 | Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| I.S. EN ISO 2580-2:2004 | PLASTICS - ACRYLONITRILE/BUTADIENE/STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 89:2015 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| DIN EN 13706-3:2003-02 | REINFORCED PLASTICS COMPOSITES - SPECIFICATIONS FOR PULTRUDED PROFILES - PART 3: SPECIFIC REQUIREMENTS |
| DIN EN 13706-2:2003-02 | REINFORCED PLASTICS COMPOSITES - SPECIFICATIONS FOR PULTRUDED PROFILES - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS |
| DIN ISO 5355:2006-05 | ALPINE SKI-BOOTS - REQUIREMENTS AND TEST METHODS |
| DIN EN 1456-1:2001-12 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPING COMPONENTS AND THE SYSTEM |
| EN 12324-2:1999 | Irrigation techniques - Reel machine systems - Part 2: Specifications of polyethylene tubes for reel machines |
| DIN EN 13244-1:2003-04 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: GENERAL |
| EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| DIN EN 1452-2:1999-09 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: PIPES |
| DIN EN ISO 8257-2:2006-06 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 62011-2:2004 | Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| EN 10288:2002 | Steel tubes and fittings for onshore and offshore pipelines - External two layer extruded polyethylene based coatings |
| EN 60811-1-3:1995/A1:2001 | INSULATING AND SHEATHING MATERIALS OF ELECTRIC CABLES - COMMON TEST METHODS - PART 1-3: GENERAL APPLICATION - METHODS FOR DETERMINING THE DENSITY - WATER ABSORPTION TESTS - SHRINKAGE TEST |
| EN 1337-5:2005 | Structural bearings - Part 5: Pot bearings |
| EN 60893-2:2004 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| ONORM EN ISO 11542-2 : 2009 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 61854:1998 | Overhead lines. Requirements and tests for spacers |
| 05/30137367 DC : DRAFT JUL 2005 | ISO 2321 - RUBBER THREADS - METHOD OF TEST |
| SAE J 1639 : 1995(S2017) | CLASSIFICATION SYSTEM FOR AUTOMOTIVE POLYAMIDE (PA) PLASTICS |
| 95/714421 DC : 0 | PREN 2833-3 - AEROSPACE SERIES - GLASS FIBRE THERMOSETTING PREIMPREGNATES - TECHNICAL SPECIFICATION - PART 3: GLASS FABRIC/EPOXY RESIN PREIMPREGNATE CURING AT UP TO 180 DEGREE C FOR CONTINUOUS USE UP TO 120 DEGREE C |
| 07/30165210 DC : 0 | BS EN ISO 10350-2 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS |
| I.S. EN 13244-1:2002 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - GENERAL |
| BS EN 60811-1-3:1995 | Insulating and sheathing materials of electric cables. Common test methods. General application Methods for determining the density. Water absorption tests. Shrinkage test |
| 03/105579 DC : DRAFT APR 2003 | ISO 17744 - PLASTICS - DETERMINATION OF SPECIFIC VOLUME AS A FUNCTION OF TEMPERATURE AND PRESSURE (PVT DIAGRAM) - PISTON APPARATUS METHOD |
| BS ISO 8986-1 : 1995 AMD 10639 | PLASTICS - POLYBUTENE (PB) MOULDING AND EXTRUSION MATERIALS - DESIGNATION STANDARD AND BASIS FOR SPECIFICATIONS |
| 98/123516 DC : DRAFT JULY 1998 | PREN 13121-1 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - ACCEPTANCE CONDITIONS AND USAGE CONDITIONS |
| 15/30297978 DC : 0 | BS EN 60404-13 ED 2.0 - MAGNETIC MATERIALS - PART 13: METHODS OF MEASUREMENT OF RESISTIVITY; DENSITY AND STACKING FACTOR OF ELECTRICAL STEEL STRIP AND SHEET |
| BS ISO 2897-2 : 1994 AMD 10661 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 7391-2 : 1996 AMD 10746 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 15/30330892 DC : 0 | BS ISO 9349 - PREINSULATED DUCTILE IRON PIPELINE SYSTEMS |
| BS ISO 17744:2004 | Plastics. Determination of specific volume as a function of temperature and pressure (pVT diagram). Piston apparatus method |
| BS ISO 4894-2 : AMD 10662 | PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ASTM D 5575 : 2007 : R2013 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| BS ISO 8257-2:1990 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| NF EN 61854 : 2001 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| PREN 4365 : 200P1 | AEROSPACE SERIES - HEAT AND CRAZING RESISTANT CAST ACRYLIC, CROSSLINKED, AND LOW MOISTURE ABSORPTION - PROPERTIES |
| SAE J 1875 : 2001 | MATERIALS FOR PLASTIC CHECK VALVES FOR VACUUM BOOSTER SYSTEMS |
| PREN 6044-2 : 200P1 | AEROSPACE SERIES - CARBON FIBRE REINFORCED EPOXY PREPREG - TECHNICAL SPECIFICATION - QUALIFICATION PROGRAMM/BATCH RELEASE TESTING - UNIDIRECTIONAL TAPE 180 DEGREE C CURING CLASS |
| CEI EN 61854 : 2000 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| BIS IS 13360-2-2 : 2013 | PLASTICS - METHODS OF TESTING - PART 2: SAMPLING AND PREPARATION OF TEST SPECIMENS - SECTION 2: COMPRESSION MOULDED TEST SPECIMENS OF THERMOPLASTIC MATERIALS |
| I.S. EN 50290-2-33:2016 | COMMUNICATION CABLES - PART 2-33: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION COMPOUNDS FOR MULTI ELEMENT METALLIC CABLES FOR INDOOR INSTALLATION (DATA CABLE) |
| IEC 60674-2:2016 | Specification for plastic films for electrical purposes - Part 2: Methods of test |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| XP ISO/TS 14569-1 : 2002 XP | DENTAL MATERIALS - GUIDANCE ON TESTING OF WEAR RESISTANCE - PART 1: WEAR BY TOOTH BRUSHING |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| ASTM F 2026 : 2017 : REDLINE | Standard Specification for Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications |
| ISO 8606:1990 | Plastics — Prepregs — Bulk moulding compound (BMC) and dough moulding compound (DMC) — Basis for a specification |
| I.S. EN 13121-1:2003 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS |
| DIN EN ISO 295:2004-05 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| DIN EN ISO 14530-2:2000-08 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999 |
| DIN EN 1337-5:2005-07 | Structural bearings - Part 5: Pot bearings |
| BS EN ISO 4894-2:1999 | Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 4613-2:1995 | Plastics. Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DIN EN ISO 2580-2:2004-05 | PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 15526-2:2004 | Plastics. Polyketone (PK) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 26:1998 | Gas fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners |
| BS EN ISO 14528-2:2000 | Plastics. Melamine-formaldehyde powder moulding compounds (MF-PMCs) Preparation of test specimens and determination of properties |
| EN 61854:1998 | Overhead lines - Requirements and tests for spacers |
| BS EN 1337-5:2005 | Structural bearings Pot bearings |
| I.S. EN ISO 15526-2:2004 | PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 60893-2:2004 | INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| I.S. EN ISO 8257-2:2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 12777-3:2003-06 | METHODS OF TEST FOR PALLET JOINTS - PART 3: DETERMINATION OF STRENGTH OF PALLET JOINTS |
| I.S. EN ISO 14663-2:2006 | PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| NF EN ISO 11542-2 : 1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ONORM ISO 5355 : 2006 | ALPINE SKI-BOOTS - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 4894-2:1999 | PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 11542-2:1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN 16972:1995-03 | COMPRESSION MOULDED PLATES MADE OF POLYETHYLENE HIGH DENSITY (PE-UHMW), (PE-HMW), (PE-HD) - TECHNICAL SPECIFICATIONS |
| DIN EN ISO 15526-2:2004-10 | PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 858-1:2002-05 | CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - PART 1: SAFETY AND EMC REQUIREMENTS FOR THE EQUIPMENT FOR THE STORAGE OF BULK MATERIALS IN SILOS, BUNKERS, BINS AND HOPPERS |
| I.S. EN ISO 10366-2:2004 | PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| NF EN ISO 2580-2 : 2004 | PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| NF EN 12245 : 2009 + A1 2012 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| BS 3412:1992 | Methods of specifying general purpose polyethylene materials for moulding and extrusion |
| BS 4936:1987 | Method of specifying styrene-acrylonitrile (SAN) moulding and extrusion materials |
| BS 1493:1987 | Method of specifying general purpose polystyrene (PS) moulding and extrusion materials |
| 02/121748 DC : DRAFT APR 2002 | PREN 438-3 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 3: CLASSIFICATION AND SPECIFICATIONS FOR LAMINATES LESS THAN 2 MM THICK INTENDED FOR BONDING TO SUPPORTING SUBSTRATES |
| BS 3531-21:1986 | Surgical implants Specification for ultra-high molecular mass polyethylene in moulded form |
| BS 7251-7:1990 | Orthopaedic joint prostheses Guide to hip joint simulators |
| 96/709571 DC : DRAFT JUL 1996 | PREN 10286 - STEEL TUBES AND FITTINGS FOR ON AND OFFSHORE PIPELINES - EXTERNAL THREE LAYER EXTRUDED POLYPROPYLENE BASED COATINGS |
| BS EN 50342-5:2010 | Lead-acid starter batteries Properties of battery housings and handles |
| I.S. EN ISO 2897-2:2004 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 97/713394 DC : DRAFT AUG 1997 | PREN 4365 - AEROSPACE STANDARD - HEAT AND CRAZING RESISTANT ACRYLIC - CAST AND CROSS LINKED - LOW MOISTURE ABSORPTION - PROPERTIES |
| 13/30281390 DC : 0 | BS EN 50290-2-25 - COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| 10/30191247 DC : DRAFT APR 2010 | BS EN ISO 13628-16 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 16: SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
| ASTM D 5577 : 1994 : R2003 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics |
| 11/30187339 DC : 0 | BS EN ISO 12736 - PETROLEUM AND NATURAL GAS INDUSTRIES - WET THERMAL INSULATION COATINGS FOR PIPELINES, FLOW LINES, EQUIPMENT AND SUBSEA STRUCTURES |
| 97/713395 DC : DRAFT AUG 1997 | PREN 4366 - AEROSPACE STANDARD - HEAT AND CRAZING RESISTANT ACRYLIC - CAST, CROSSLINKED AND MULTI-AXIALLY STRETCHED - LOW MOISTURE ABSORPTION - PROPERTIES |
| BS 2782-6 Method 631A:1982 | Methods of testing plastics. Dimensional properties Determination of gravimetric thickness and yield of flexible sheet |
| DIN EN 61854 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| 97/713388 DC : DRAFT AUG 1997 | PREN 2719 - AEROSPACE SERIES - POLYCARBONATE SHEET - TECHNICAL SPECIFICATION |
| BS 7933-1:1998 | Electric cables. Accessories. Material characterization Resinous compounds before cure and in the cured state |
| NFC 33 009-1 : 2008 | ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 1: FINGERPRINTING AND TYPE TESTS FOR RESINOUS COMPOUNDS |
| BS ISO 11542-1:1994 | Plastics. Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials Designation system and basis for specifications |
| 09/30193091 DC : 0 | BS EN 60811-606 - ELECTRIC AND OPTICAL FIBRE CABLES - TEST METHODS FOR NON-METALLIC MATERIALS - PART 606: PHYSICAL TESTS - METHODS FOR DETERMINING THE DENSITY |
| 04/30091878 DC : DRAFT FEB 2004 | BS EN ISO 13000-2 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 2580-2 : 94 AMD 10660 | PLASTICS - ACRYLONITRILE/BUTADIENE/STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| CEI EN 62011-2 : 2005 | INSULATING MATERIALS - INDUSTRIAL, RIGID, MOULDED, LAMINATED TUBES AND RODS OF RECTANGULAR AND HEXAGONAL CROSS-SECTION, BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| BS ISO 1163-2 : 1995 AMD 10744 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) MOULDING AND EXTRUSION MATERIALS |
| 97/107906 DC : DRAFT DEC 1997 | PREN 13022-1 - GLASS IN BUILDING - STRUCTURAL SEALANT GLAZING - PART 1: ACTIONS, REQUIREMENTS AND TERMINOLOGY |
| 04/30122412 DC : DRAFT SEP 2004 | ISO 17194 - STRUCTURAL ADHESIVES - STANDARD DATABASE OF PROPERTIES |
| BS 2782-3:Method 323E:1997 | Methods of testing plastics. Mechanical properties Longitudinal and shear vibration. Wave-propagation method |
| BS ISO 2898-2 : 1997 AMD 10727 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 1622-2 : 1995 AMD 10649 | PLASTICS - POLYSTYRENE (PS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| PREN 4364 : 200P1 | AEROSPACE SERIES - CAST ACRYLIC - PROPERTIES |
| EN ISO 14631:1999 | Extruded sheets of impact-modified polystyrene (PS-I) - Requirements and test methods (ISO 14631:1999) |
| PREN 2833-1 : 200P2 | AEROSPACE SERIES - GLASS FIBRE THERMOSETTING PREIMPREGNATES - TECHNICAL SPECIFICATION - PART 1: GENERAL REQUIREMENTS |
| NFT 54 405-1 : 2002 | UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U) EXTRUDED OR COEXTRUDED PROFILES FOR OUTSIDE USE - SPECIFICATIONS AND TEST METHODS - PART 1: SOLID WALL PVC-U |
| NF EN 2564 : 1998 | AEROSPACE SERIES - CARBON FIBRE LAMINATES - DETERMINATION OF THE FIBRE, RESIN AND VOID CONTENTS |
| I.S. EN 61854:1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| ISO 5355:2005 | Alpine ski-boots Requirements and test methods |
| ASTM D 4203 : 2017 : REDLINE | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM D 5857 : 2017 : REDLINE | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
| ASTM D 5936 : 1996 | Specification for Multipurpose Test Specimens (Withdrawn 1998) |
| ISO 4591:1992 | Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) |
| ISO 17282:2004 | Plastics — Guide to the acquisition and presentation of design data |
| NF EN ISO 8257-2 : 2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 2897-2:2004-05 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 6402-2:2004-05 | PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE-(ETHYLENE-PROPYLENE-DIENE)-STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 13121-1:2003 | GRP tanks and vessels for use above ground Raw materials. Specification conditions and acceptance conditions |
| IEC 60404-13:1995 | Magnetic materials - Part 13: Methods of measurement of density, resistivity and stacking factor of electrical steel sheet and strip |
| BS EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| BS EN 13706-2:2002 | Reinforced plastics composites. Specifications for pultruded profiles Method of test and general requirements |
| ISO 1163-2:1995 | Plastics Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 12777-3:2002 | Methods of test for pallet joints Determination of strength of pallet joints |
| EN ISO 14663-2:2006 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 14663-2:1999) |
| EN 2564:1998 | Aerospace series - Carbon fibre laminates - Determination of the fibre, resin and void contents |
| UNI EN 16245-2 : 2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| EN 50290-2-33:2016 | Communication cables - Part 2-33: Common design rules and construction - Polyethylene insulation compounds for multi element metallic cables for indoor installation (data cable) |
| BS ISO 1268-3:2000 | Fibre-reinforced plastics. Methods of producing test plates Wet compression moulding |
| I.S. EN ISO 6402-2:2004 | PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE - (ETHYLENE-PROPYLENE-DIENE) - STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 2564:1998 | Carbon fibre laminates. Determination of the fibre, resin and void contents |
| BS ISO 7792-2 : 1997 AMD 15252 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS 2782-6 Methods 620A to 620D:1980 | Methods of testing plastics. Dimensional properties Determination of density of solid plastics excluding cellular plastics (immersion method). Determination of density of solid plastics excluding cellular plastics (pyknometer method). Determination of density of solid plastics excluding cellular plastics (sink-float method). Determination of density of solid plastics excluding cellular plastics (density gradient column method) |
| 05/30137738 DC : DRAFT AUG 2005 | ISO 9523 - TOURING SKI-BOOTS FOR ADULTS - INTERFACE WITH TOURING SKI-BINDINGS - REQUIREMENTS AND TEST METHODS |
| 04/30031040 DC : 0 | ISO 5834-3 - IMPLANTS FOR SURGERY - ULTRA-HIGH MOLECULAR WEIGHT POLYETHYLENE - PART 3: ACCELERATED AGEING METHODS |
| 02/121750 DC : DRAFT APR 2002 | PREN 438-5 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 5: CLASSIFICATION AND SPECIFICATIONS FOR FLOORING GRADE LAMINATES LESS THAN 2 MM THICK |
| BS ISO 1268-1:2001 | Fibre-reinforced plastics. Methods of producing test plates General conditions |
| 02/709771 DC : DRAFT AUG 2002 | ISO/DIS 9349 - PREINSULATED DUCTILE IRON PIPELINE SYSTEMS |
| UNE-EN ISO 23996:2012 | Resilient floor coverings - Determination of density (ISO 23996:2007) |
| BS EN 45510-6-6:2000 | Guide for the procurement of power station equipment. Turbine auxiliaries Turbine auxiliaries. Wet and wet/dry cooling towers - Section 6: Wet/dry cooling towers |
| SAE AMS 3970/6 : 2011 | CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 6 - MATERIAL SPECIFICATION: CARBON FIBER FABRIC REINFORCED EPOXY PREPREG FOR REPAIR, PLAIN WEAVE FABRIC, 193 G/M[2], ADHESIVE FILM FOR REPAIR AND NON-STRUCTURAL GLASS FIBER FABRIC REINFORCED EPOXY PREPREG, 105 G/M[2] |
| 16/30346715 DC : 0 | BS EN 2564 - AEROSPACE SERIES - CARBON FIBRE LAMINATES - DETERMINATION OF THE FIBRE, RESIN- AND VOID CONTENTS |
| CEI UNI EN 45510-6-6 : 2000 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 6-6: TURBINE AUXILIARIES - WET AND WET/DRY COOLING TOWERS |
| 06/30136510 DC : DRAFT JULY 2006 | ISO 23996 - RESILIENT FLOOR COVERINGS - DETERMINATION OF DENSITY |
| BS ISO 14663-2 : 1999 AMD 16029 | PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 04/30091867 DC : DRAFT FEB 2004 | BS EN ISO 12086-1 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| BS ISO 10366-2 : 94 AMD 10665 | PLASTICS - METHYL METHYLACRYLATE/ACRYLONITRILE/BUTADIENE/STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 14632:1999 | EXTRUDED SHEETS OF POLYETHYLENE (PE-HD) - REQUIREMENTS AND TEST METHODS |
| BS ISO 3673-1 : 1996 AMD 10743 | PLASTICS - EPOXY RESINS - DESIGNATION |
| BS ISO 12086-2 : 2001 AMD 10637 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS |
| BS EN 60674-2:2017+A1:2019 | Specification for plastic films for electrical purposes Methods of test |
| NF EN 60674-2 : 98 AMD 1 2002 | SPECIFICATION FOR PLASTIC FILMS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| ISO 1268-1:2001 | Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions |
| I.S. 266-1:1991 | POLYETHYLENE (PE) PIPES AND FITTINGS FOR NATURAL GAS, MANUFACTURED GAS AND LIQUEFIED PETROLEUM GAS - PART 1: PIPES |
| NF EN ISO 10366-2 : 2004 | PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| IEC 61854:1998 | Overhead lines - Requirements and tests for spacers |
| DIN EN ISO 11542-2:2010-01 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998 + Cor. 1:2007) (includes Corrigendum AC:2008) |
| BS EN ISO 14529-2:2000 | Plastics. Melamine/phenolic powder moulding compounds (MP-PMCs) Preparation of test specimens and determination of properties |
| ISO 12777-3:2002 | Methods of test for pallet joints — Part 3: Determination of strength of pallet joints |
| ISO 2897-2:2003 | Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 12777-2:2000 | Methods of test for pallet joints — Part 2: Determination of withdrawal and head pull-through resistance of pallet nails and staples |
| BS EN 12576:1998 | Plastics. Fibre reinforced composites. Preparation of compression moulded test plates of SMC, BMC and DMC |
| ISO 14528-2:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 1872-1:1993 | Plastics Polyethylene (PE) moulding and extrusion materials Part 1: Designation system and basis for specifications |
| BS EN 13101:2002 | Steps for underground man entry chambers. Requirements, marking, testing and evaluation of conformity |
| ISO 14632:1998 | Extruded sheets of polyethylene (PE-HD) Requirements and test methods |
| ISO 4613-2:1995 | Plastics Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN 13677-3:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Specific requirements |
| BS EN 12324-2:1999 | Irrigation techniques. Reel machine systems Specifications of polyethylene tubes for reel machines |
| BS EN 436:1994 | Resilient floor coverings. Determination of density |
| BS EN ISO 295:2004 | Plastics. Compression moulding of test specimens of thermosetting materials |
| ISO 14530-2:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 3673-1:1996 | Plastics Epoxy resins Part 1: Designation |
| BS EN ISO 10366-2:2003 | Plastics. Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 2580-2:2003 | Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 14632:1999 | Extruded sheets of polyethylene (PE-HD). Requirements and test methods |
| ISO 14631:1999 | Extruded sheets of impact-modified polystyrene (PS-I) Requirements and test methods |
| ISO 8257-2:2001 | Plastics Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 12777-2:2000 | Methods of test for pallet joints Determination of withdrawal and head pull-through resistance of pallet nails and staples |
| ISO 4894-2:1995 | Plastics Styrene/acrylonitrile (SAN) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 14529-2:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 14527-2:2000 | Preparation of test specimens and determination of properties |
| BS EN ISO 8257-2:2006 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 10350:1993 | Plastics Acquisition and presentation of comparable single-point data |
| BS EN 14598-3:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements |
| ISO 1622-2:1995 | Plastics Polystyrene (PS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 6402-2:2003 | Plastics Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 11542-2:1998 | Plastics Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 14526-2:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 10366-2:2003 | Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 1872-1:1999 | Polyethylene (PE) moulding and extrusion materials Designation system and basis for specifications |
| UNE-EN 89:2016 | Gas-fired storage water heaters for the production of domestic hot water |
| BS EN ISO 6402-2:2003 | Plastics. Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 14663-2:2006 | Plastics. Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 2897-2:2003 | Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials Preparation of test specimens and determination of properties |
| IEC 60811-1-3:1993+AMD1:2001 CSV | Common test methods for insulating and sheathing materials of electric and optical cables - Part 1-3: General application -Methods for determining the density - Water absorption tests - Shrinkage test |
| BS EN ISO 14526-2:2000 | Plastics. Phenolic powder moulding compounds (PF-PMCs) Preparation of test specimens and determination of properties |
| EN ISO 8257-2:2006 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001) |
| EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| EN ISO 1163-2:1999 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995) |
| EN ISO 15252-2:1999 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 15252-2:1999) |
| EN 1456-1 : 2001 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPING COMPONENTS AND THE SYSTEM |
| EN 13677-3:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements |
| EN 13677-2:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements |
| EN ISO 14529-2:1999 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14529-2:1999) |
| EN ISO 10366-2:2003 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 10366-2:2003) |
| EN 13706-3:2002 | Reinforced plastics composites - Specifications for pultruded profiles - Part 3: Specific requirements |
| EN ISO 15526-2:2004 | Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000) |
| EN ISO 2580-2:2003 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003) |
| EN ISO 12777-2:2000 | Methods of test for pallet joints - Part 2: Determination of withdrawal and head pull-through resistance of pallet nails and staples (ISO 12777-2:2000) |
| EN 13706-2:2002 | Reinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements |
| EN ISO 14530-2:1999 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999) |
| EN 1452-2 : 1999 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: PIPES |
| EN ISO 14528-2:1999 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14528-2:1999) |
| EN ISO 4894-2:1999 | Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995) |
| EN ISO 1622-2:1999 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1622-2:1995) |
| EN ISO 1872-1:1999 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1872-1:1993) |
| EN ISO 14526-2:1999 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999) |
| EN 14598-3:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| EN ISO 12777-3:2002 | Methods of test for pallet joints - Part 3: Determination of strength of pallet joints (ISO 12777-3:2002) |
| EN ISO 3673-1:1999 | Plastics - Epoxy resins - Part 1: Designation (ISO 3673-1:1996) |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| EN ISO 6402-2:2003 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003) |
| EN ISO 2897-2:2003 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2897-2:2003) |
| EN ISO 14527-2:1999 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF-MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14527-2:1999) |
| 05/30134174 DC : DRAFT MAY 2005 | HD 631.3 S1 ED. 1 - ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 3: FINGERPRINTING FOR HEAT SHRINKABLE COMPONENTS FOR MEDIUM VOLTAGE APPLICATIONS FROM 3,6/6 (7,2) KV UP TO 20,8/36 (42) KV |
| 98/124702 DC : DRAFT OCT 1998 | DRAFT BS 3900-K3 - METHODS OF TEST FOR PAINTS - DETERMINATION OF RELEASE RATE OF BIOCIDES FROM ANTIFOULING PAINTS - DETERMINATION OF TIN-BASED BIOCIDES IN THE EXTRACT AND CALCULATION OF THE RELEASE RATE |
| 07/30161103 DC : DRAFT JAN 2007 | BS EN 60404-13 - MAGNETIC MATERIALS - PART 13: METHODS MEASUREMENT OF DENSITY, RESISTIVITY AND STACKING FACTOR OF ELECTRICAL STEEL SHEET AND STRIP |
| BS ISO 6402-2 : 94 AMD 10652 | |
| I.S. EN 62011-2:2004 | INSULATING MATERIALS - INDUSTRIAL, RIGID, MOULDED, LAMINATED TUBES AND RODS OF RECTANGULAR AND HEXAGONAL CROSS-SECTION, BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES, - PART 2: METHODS OF TEST |
| SAE AMS 3970/1 : 2011 | CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 1 - GENERAL REQUIREMENTS |
| CEI EN 60893-2 : 2005 | INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| ISO/TS 14569-1:1999 | Dental materials Guidance on testing of wear Part 1: Wear by toothbrushing |
| BS EN 62011-2:2004 | Insulating materials. Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes Methods of test |
| 16/30329416 DC : 0 | BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| 02/704943 DC : DRAFT APR 2002 | PREN 10329 - STEEL TUBES AND FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - EXTERNAL FIELD JOINT COATINGS |
| 03/100997 DC : DRAFT MAR 2003 | BS EN 13022-2 - GLASS IN BUILDING - STRUCTURAL SEALANT GLAZING - PART 2: PRODUCT STANDARD FOR ULTRA-VIOLET RESISTANT SEALANT AND STRUCTURAL SEALANT |
| 08/30154948 DC : DRAFT FEB 2008 | BS ISO 21809-4 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 4: POLYETHYLENE COATINGS (2-LAYER PE) |
| EN ISO 14632:1998 | Extruded sheets of polyethylene (PE-HD) - Requirements and test methods (ISO 14632:1998) |
| NFC 33 009-3 : 2008 | ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 3: FINGERPRINTING FOR HEAT SHRINKABLE COMPONENTS FOR MEDIUM VOLTAGE APPLICATIONS FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV |
| 06/30148624 DC : 0 | EN 15507 - PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - COMPARATIVE MATERIAL TESTING OF POLYETHYLENE GRADES |
| BS ISO 12086-1 : 1995 AMD 10638 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| 96/709572 DC : DRAFT JUL 1996 | PREN 10287 - STEEL TUBES AND FITTINGS FOR ON AND OFFSHORE PIPELINES - EXTERNAL FUSED POLYETHYLENE BASED COATINGS |
| 08/30171587 DC : DRAFT MAY 2008 | BS ISO 7628 - ROAD VEHICLES - THERMOPLASTICS TUBING FOR AIR BRAKING SYSTEMS |
| BS ISO 1268-8:2004 | Fibre-reinforced plastics. Methods of producing test plates Compression moulding of SMC and BMC |
| 95/714422 DC : 0 | PREN 2833-4 - AEROSPACE SERIES - GLASS FIBER THERMOSETTING PREIMPREGNATES - TECHNICAL SPECIFICATION - PART 4: UNIDIRECTIONAL GLASS/EPOXY RESIN PREIMPREGNATE CURING AT UP TO 125 DEGREE C FOR CONTINUOUS USE UP TO 80 DEGREE C |
| 04/30091870 DC : DRAFT FEB 2004 | BS EN ISO 12086-2 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS 3126:1987 | Method of specifying toughened polystyrene (SB) moulding and extrusion materials |
| 02/121751 DC : DRAFT APR 2002 | PREN 438-6 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEET BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| BS ISO 11833-1:1998 | Plastics. Unplasticized poly(vinyl chloride) sheets. Tapes, dimensions and characteristics Sheets of thickness not less than 1 mm |
| SAE AMS 2980/1 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 1 - GENERAL REQUIREMENTS |
| PREN 2833-4 : 200P1 | AEROSPACE SERIES - GLASS FIBRE THERMOSETTING PREIMPREGNATES - TECHNICAL SPECIFICATION - PART 4: UNIDIRECTIONAL GLASS/EPOXY RESIN PREIMPREGNATE CURING AT UP TO 125 DEGREES C FOR CONTINUOUS USE UP TO 80 DEGREES C |
| PREN 2155-01 : 1 | AEROSPACE SERIES - TEST METHODS FOR TRANSPARENT MATERIALS FOR AIRCRAFT GLAZING - PART 1 - DETERMINATION OF THE DENSITY AND RELATIVE DENSITY |
| UNE-EN 50290-2-37:2016 | Communication cables - Part 2-37: Common design rules and construction - Polyethylene insulation for coaxial cables |
| ISO 6721-9:1997 | Plastics Determination of dynamic mechanical properties Part 9: Tensile vibration Sonic-pulse propagation method |
| PREN 50290-2-25 : DRAFT 2013 | COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| ISO 6721-8:1997 | Plastics Determination of dynamic mechanical properties Part 8: Longitudinal and shear vibration Wave-propagation method |
| API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
| BS ISO 6721-9 : 1997 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 9: TENSILE VIBRATION - SONIC-PULSE PROPAGATION METHOD |
| ASTM D 5577 : 1994 : R2010 : EDT 1 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics (Withdrawn 2019) |
| ISO 8085-2:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels Metric series Specifications Part 2: Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings |
| NF ISO 5355 : 2006 | ALPINE SKI-BOOTS - REQUIREMENTS AND TEST METHODS |
| ISO 6691:2000 | Thermoplastic polymers for plain bearings Classification and designation |
| ISO 10933:1997 | Polyethylene (PE) valves for gas distribution systems |
| DIN EN ISO 10366-2:2004-05 | PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 1163-2:2000 | Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 13199-3:2000 | Packaging. Small load carrier systems Bond Stackable System (BSS) |
| ISO 15252-2:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 14631:1999 | Extruded sheets of impact-modified polystyrene (PS-I). Requirements and test methods |
| ISO 14663-2:1999 | Plastics Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 14527-2:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 3673-1:2000 | Plastics. Epoxy resins Designation |
| ISO 15526-2:2000 | Plastics Polyketone (PK) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN 858-1:2002 | Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control |
| BS EN ISO 14530-2:2000 | Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs) Preparation of test specimens and determination of properties |
| BS EN ISO 15252-2:2000 | Plastics. Epoxy powder moulding compounds (EP-PMCs) Preparation of test specimens and determination of properties |
| EN 13101:2002 | Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity |
| EN 13199-3:2000 | Packaging - Small Load Carrier Systems - Part 3: Bond Stackable System (BSS) |
| NF EN ISO 2897-2 : 2004 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 14663-2:2006-06 | PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 10288:2003-12 | STEEL TUBES AND FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - EXTERNAL TWO-LAYER EXTRUDED POLYETHYLENE BASED COATINGS |
| BS 2782-9.902A(1992) : 1992 AMD 10344 | METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS |
| BS 4935:1989 | Method of specifying acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials |
| BS 7008-1(1994) : AMD 8821 | ACQUISITION AND PRESENTATION OF COMPARABLE DATA FOR BASIC PROPERTIES OF PLASTICS - METHOD FOR SINGLE POINT DATA |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.