IEC 62052-31:2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electricity metering equipment (AC) - General requirements, tests and test conditions - Part 31: Product safety requirements and tests
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
25-10-2024
Superseded by
Language(s)
English, English - French
Published date
15-09-2015
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Terms and definitions
4 Tests
5 Information and marking requirements
6 Protection against electrical shock
7 Protection against mechanical hazards
8 Resistance to mechanical stresses
9 Protection against spread of fire
10 Equipment temperature limits and resistance to heat
11 Protection against penetration of dust and water
12 Protection against liberated gases and substances
explosion and implosion - Batteries and battery charging
13 Components and sub-assemblies
14 Hazards resulting from application - Reasonably
foreseeable misuse
15 Risk assessment
Annex A (normative) - Measuring circuits for touch current
Annex B (informative) - Examples for insulation between parts
Annex C (informative) - Examples for direct connected meters
equipped with supply control and load control switches
Annex D (normative) - Test circuit diagram for the test of long
term overvoltage withstand
Annex E (normative) - Test circuit diagram for short current
test on the current circuit of direct connected meters
Annex F (informative) - Examples for voltage tests
Annex G (normative) - Additional a.c. voltage tests for
electromechanical meters
Annex H (normative) - Test equipment for cable flexion
and pull test
Annex I (informative) - Routine tests
Annex J (informative) - Examples of battery protection
Annex K (informative) - Rationale for specifying overvoltage
category III
Annex L (informative) - Overview of safety aspects covered
Annex M (informative) - Index of defined terms
Bibliography
IEC 62052-31:2015 specifies product safety requirements for equipment for electrical energy measurement and control. It applies to newly manufactured metering equipment designed to measure and control electrical energy on 50 Hz or 60 Hz networks with a voltage up to 600 V, where all functional elements, including add-on modules are enclosed in or form a single case. When such equipment is designed to be installed in a specified matching socket, then the requirements apply to, and the tests shall be performed on, equipment installed in its specified matching socket. However, requirements for sockets and inserting / removing the meters from the socket are outside the scope of this standard. This International Standard is also applicable to auxiliary input and output circuits.
This bilingual version (2016-11) corresponds to the monolingual English version, published in 2015-09.
The contents of the Interpretation Sheet 1 of June 2019 have been included in this copy.
| Committee |
TC 13
|
| DevelopmentNote |
Stability date: 2020. (09/2015)
|
| DocumentType |
Standard
|
| Pages |
187
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DIN EN 62052-31 Berichtigung 2:2021-10 | Identical |
| VDE 0418-2-31 Berichtigung 2:2021-10 | Identical |
| ONORM OVE EN 62052-31 : 2017 | Identical |
| NF EN 62052-31 : 2017 | Identical |
| NEN EN IEC 62052-31 : 2016 | Identical |
| PN EN 62052-31 : 2016 | Identical |
| SN EN 62052-31 : 2016 | Identical |
| VDE 0418-2-31 : 2017 | Identical |
| DIN EN 62052-31 : 2017 | Identical |
| CEI EN 62052-31 : 2016 | Identical |
| EN 62052-31:2016 | Identical |
| BS EN 62052-31:2016 | Identical |
| PNE-EN 62052-31 | Identical |
| UNE-EN 62052-31:2016 | Identical |
| 15/30328426 DC : DRAFT JULY 2015 | BS EN 62053-22/AMD1 - ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 22: STATIC METERS FOR ACTIVE ENERGY (CLASSES 0,2 S AND 0,5 S) |
| I.S. EN 62053-11:2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 11: ELECTROMECHANICAL METERS FOR ACTIVE ENERGY (CLASSES 0,5, 1 AND 2) |
| EN 62053-24 : 2015 AMD 1/COR 18 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 24: STATIC METERS FOR REACTIVE ENERGY AT FUNDAMENTAL FREQUENCY (CLASSES 0,5 S, 1 S AND 1) (IEC 62053-24:2014/A1:2016/COR1:2018) |
| EN 62053-11:2003/A1:2017/AC:2018-05 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 11: ELECTROMECHANICAL METERS FOR ACTIVE ENERGY (CLASSES 0,5, 1 AND 2) (IEC 62053-11:2003/A1:2016/COR1:2018) |
| EN 62054-21:2004/A1:2017/AC:2018-04 | ELECTRICITY METERING (AC) - TARIFF AND LOAD CONTROL - PART 21: PARTICULAR REQUIREMENTS FOR TIME SWITCHES (IEC 62054-21:2004/A1:2017/COR1:2018) |
| 15/30328434 DC : 0 | BS EN 62054-11/AMD1 - ELECTRICITY METERING (A.C.) - TARIFF AND LOAD CONTROL - PART 11: PARTICULAR REQUIREMENTS FOR ELECTRONIC RIPPLE CONTROL RECEIVERS |
| 15/30328422 DC : DRAFT JULY 2015 | BS EN 62053-21/AMD1 - ELECTRICITY METERING EQUIPMENT (A.C.) -PARTICULAR REQUIREMENTS - PART 21: STATIC METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) |
| 15/30328410 DC : DRAFT JULY 2015 | BS EN 62052-11/AMD1 - ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 11: METERING EQUIPMENT |
| BS EN 62054-11 : 2004 | ELECTRICITY METERING (A.C.) - TARIFF AND LOAD CONTROL - PART 11: PARTICULAR REQUIREMENTS FOR ELECTRONIC RIPPLE CONTROL RECEIVERS (IEC 62054-11:2004) |
| 15/30328430 DC : 0 | BS EN 62053-24/AMD1 - ELECTRICITY METERING EQUIPMENT (AC) - PARTICULAR REQUIREMENTS - PART 24: STATIC METERS FOR REACTIVE ENERGY AT FUNDAMENTAL FREQUENCY (CLASSES 0,5 S, 1 S AND 1) |
| CEI EN 62056-7-5 : 1ED 2017 | ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: LOCAL DATA TRANSMISSION PROFILES FOR LOCAL NETWORKS (LN) |
| I.S. EN 62052-21:2004 | ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 21: TARIFF AND LOAD CONTROL EQUIPMENT |
| I.S. EN 62052-11:2003 | ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 11: METERING EQUIPMENT |
| IEC 62053-23:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements -Part 23: Static meters for reactive energy (classes 2 and 3) |
| BS EN 62053-24 : 2015 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 24: STATIC METERS FOR REACTIVE ENERGY AT FUNDAMENTAL FREQUENCY (CLASSES 0,5 S, 1 S AND 1) (IEC 62053-24:2014) |
| BS EN 62053-22 : 2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 22: STATIC METERS FOR ACTIVE ENERGY (CLASSES 0,2 S AND 0,5 S) (IEC 62053-22:2003) |
| I.S. EN 62053-21:2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 21: STATIC METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) |
| BS EN 62053-23 : 2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 23: STATIC METERS FOR REACTIVE ENERGY (CLASSES 2 AND 3) (IEC 62053-23:2003) |
| IEC 62053-21:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements - Part 21: Static meters for active energy (classes 1 and 2) |
| IEC 62056-7-5:2016 | Electricity metering data exchange - The DLMS/COSEM suite - Part 7-5: Local data transmission profiles for Local Networks (LN) |
| IEC TS 62056-6-9:2016 | Electricity metering data exchange - The DLMS/COSEM suite - Part 6-9: Mapping between the Common Information Model message profiles (IEC 61968-9) and DLMS/COSEM (IEC 62056) data models and protocols |
| 15/30328418 DC : DRAFT JULY 2015 | BS EN 62053-11/AMD1 - ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 11: ELECTROMECHANICAL METERS FOR ACTIVE ENERGY (CLASSES 0,5, 1 AND 2) |
| BS EN 62053-11 : 2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 11: ELECTROMECHANICAL METERS FOR ACTIVE ENERGY (CLASSES 0.5, 1 AND 2) (IEC 62053-11:2003) |
| PD IEC/TS 62056-6-9:2016 | Electricity metering data exchange. The DLMS/COSEM suite Mapping between the Common Information Model message profiles (IEC 61968-9) and DLMS/COSEM (IEC 62056) data models and protocols |
| 15/30328414 DC : DRAFT JULY 2015 | BS EN 62052-21/AMD1 - ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 21: TARIFF AND LOAD CONTROL EQUIPMENT |
| 15/30328442 DC : 0 | BS EN 62053-23/AMD1 - ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 23: STATIC METERS FOR REACTIVE ENERGY (CLASSES 2 AND 3) |
| I.S. EN 62054-21:2004 | ELECTRICITY METERING (A.C.) - TARIFF AND LOAD CONTROL - PART 21: PARTICULAR REQUIREMENTS FOR TIME SWITCHES |
| IEC 62052-21:2004+AMD1:2016 CSV | Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 21: Tariff and load control equipment |
| IEC 62052-11:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 11: Metering equipment |
| IEC 62054-11:2004+AMD1:2016 CSV | Electricity metering (a.c.) - Tariff and load control - Part 11:Particular requirements for electronic ripple control receivers |
| IEC 62054-21:2004+AMD1:2017 CSV | Electricity metering (AC) - Tariff and load control - Part 21: Particular requirements for time switches |
| IEC 62053-22:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular Requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S) |
| BS EN 62056-7-5:2016 | Electricity metering data exchange. The DLMS/COSEM suite Local data transmission profiles for Local Networks (LN) |
| I.S. EN 62054-11:2004 | ELECTRICITY METERING (A.C.) - TARIFF AND LOAD CONTROL - PART 11: PARTICULAR REQUIREMENTS FOR ELECTRONIC RIPPLE CONTROL RECEIVERS |
| 14/30302871 DC : 0 | BS EN 62056-7-5 - ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: COMMUNICATION PROFILES FOR LOCAL DATA TRANSMISSION |
| I.S. EN 62056-7-5:2016 | ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: LOCAL DATA TRANSMISSION PROFILES FOR LOCAL NETWORKS (LN) |
| I.S. EN 62053-24:2015 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 24: STATIC METERS FOR REACTIVE ENERGY AT FUNDAMENTAL FREQUENCY (CLASSES 0,5 S, 1 S AND 1) (IEC 62053-24:2014/A1:2016/COR1:2018) |
| BS EN 62053-21 : 2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 21: STATIC METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) (IEC 62053-21:2003) |
| IEC 62053-11:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements - Part 11: Electromechanical meters for active energy (classes 0,5, 1and 2) |
| EN 62056-7-5:2016 | Electricity metering data exchange - The DLMS/COSEM suite - Part 7-5: Local data transmission profiles for Local Networks (LN) |
| EN 62054-11:2004/A1:2017/AC:2018-04 | ELECTRICITY METERING (A.C.) - TARIFF AND LOAD CONTROL - PART 11: PARTICULAR REQUIREMENTS FOR ELECTRONIC RIPPLE CONTROL RECEIVERS |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 60038:2009 | IEC standard voltages |
| ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
| IEC 62052-21:2004+AMD1:2016 CSV | Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 21: Tariff and load control equipment |
| DIN 46228-1:1992-08 | TUBULAR END-SLEEVES WITHOUT PLASTIC SLEEVE |
| IEC 62053-23:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements -Part 23: Static meters for reactive energy (classes 2 and 3) |
| IEC 60228:2004 | Conductors of insulated cables |
| IEC 61869-3:2011 | Instrument transformers - Part 3: Additional requirements for inductive voltage transformers |
| IEC 62053-21:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements - Part 21: Static meters for active energy (classes 1 and 2) |
| UL 1439:5ED 2015-04-21 | Tests for Sharpness of Edges on Equipment |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| IEC 60688:2012 | Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC 61643-12:2008 | Low-voltage surge protective devices - Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles |
| IEC 62054-21:2004+AMD1:2017 CSV | Electricity metering (AC) - Tariff and load control - Part 21: Particular requirements for time switches |
| IEC 62053-11:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements - Part 11: Electromechanical meters for active energy (classes 0,5, 1and 2) |
| IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV | Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| IEC 62053-52:2005 | Electricity metering equipment (AC) - Particular requirements - Part 52: Symbols |
| IEC 60332-2-2:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Low-voltage fuses - Part 1: General requirements |
| IEC 62052-11:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 11: Metering equipment |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| CENELEC GUIDE 29 : 2007 | TEMPERATURES OF HOT SURFACES LIKELY TO BE TOUCHED GUIDANCE DOCUMENT FOR TECHNICAL COMMITTEES AND MANUFACTURERS |
| IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
| IEC 61010-2-030:2017 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits |
| IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
| IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame |
| IEC 62053-31:1998 | Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only) |
| EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| ISO 780:2015 | Packaging Distribution packaging Graphical symbols for handling and storage of packages |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60269-3:2010+AMD1:2013 CSV | Low-voltage fuses - Part 3: Supplementary requirements for fuses foruse by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F |
| IEC TR 61000-2-14:2006 | Electromagnetic compatibility (EMC) - Part 2-14: Environment - Overvoltages on public electricity distribution networks |
| IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| IEC 60721-3-0:1984+AMD1:1987 CSV | Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Introduction |
| IEC GUIDE 104:2010 | The preparation of safety publications and the use of basic safety publications and group safety publications |
| IEC 60255-27:2013 | Measuring relays and protection equipment - Part 27: Product safety requirements |
| IEC 62058-31:2008 | Electricity metering equipment (AC) - Acceptance inspection - Part 31: Particular requirements for static meters for active energy (classes 0,2 S, 0,5 S, 1 and 2) |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 61051-2:1991 | Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| IEC 60898-1:2015 | Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations - Part 1: Circuit-breakers for a.c. operation |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| IEC 62053-22:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular Requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S) |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 62477-1:2012+AMD1:2016 CSV | Safety requirements for power electronic converter systems and equipment - Part 1: General |
| IEC 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 62055-31:2005 | Electricity metering - Payment systems - Part 31: Particular requirements - Static payment meters for active energy (classes 1 and 2) |
| IEC 61180-1:1992 | High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 62058-11:2008 | Electricity metering equipment (AC) - Acceptance inspection - Part 11: General acceptance inspection methods |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC TR 60664-2-1:2011 | Insulation coordination for equipment within low-voltage systems - Part 2-1: Application guide - Explanation of the application of the IEC 60664 series, dimensioning examples and dielectric testing |
| IEC 62054-11:2004+AMD1:2016 CSV | Electricity metering (a.c.) - Tariff and load control - Part 11:Particular requirements for electronic ripple control receivers |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| IEC 60364-5-52:2009 | Low-voltage electrical installations - Part 5-52: Selection and erection of electrical equipment - Wiring systems |
| IEC 62058-21:2008 | Electricity metering equipment (AC) - Acceptance inspection - Part 21: Particular requirements for electromechanical meters for active energy (classes 0,5, 1 and 2) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.