IEC 60793-1-40:2001
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
31-12-2021
Superseded by
Language(s)
English - French
Published date
26-07-2001
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 Calibration requirements
5 Reference test method
6 Apparatus
7 Sampling and specimens
7.1 Specimen length
7.2 Specimen end face
8 Procedure
9 Calculations
9.1 Methods A and B
9.2 Method C
9.3 Method D
10 Results
10.1 Information available with each measurement
10.2 Information available upon request
11 Specification information
Annex A (normative) Requirements specific to
method A - Cut-back
Annex B (normative) Requirements specific to
method B - Insertion loss
Annex C (normative) Requirements specific to
method C - Backscattering
Annex D (normative) Requirements specific to
method D - Spectral attenuation modelling
Figures
Tables
Establishes uniform requirements for measuring the attenuation of optical fibres. Four methods are described: (a) cut-back, (b) insertion loss, (d) backscattering, (d) modelling spectral attenuation. Methods (a), (b) and (c) apply to all categories of class A multimode fibres and class B single-mode fibres. Method (c), backscattering, also covers the location, losses and characterization of point discontinuities. Method (d) has been demonstrated only on class B fibres.
| Committee |
TC 86/SC 86A
|
| DevelopmentNote |
Supersedes IEC 60793-1-4 (08/2001) Stability Date: 2019. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
57
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| I.S. EN 60793-1-40:2004 | Identical |
| DIN EN 60793-1-40 : 2004 | Identical |
| EN 60793-1-40:2003 | Identical |
| BIS IS/IEC 60793-1-40 : 2001 | Identical |
| NEN EN IEC 60793-1-40 : 2004 | Identical |
| BS EN 60793-1-40:2003 | Identical |
| NF EN 60793-1-40 : 2004 | Identical |
| GOST R IEC 60793-1-40 : 2012 | Identical |
| VDE 0888-240 : 2004 | Identical |
| UNE-EN 60793-1-40:2003 | Identical |
| 14/30296116 DC : 0 | BS EN 60793-2-30 - OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| 08/30195475 DC : 0 | BS EN 60793-1-44 - OPTICAL FIBRES - PART 1-44: MEASUREMENT METHODS AND TEST PROCEDURES - CUT-OFF WAVELENGTH |
| 02/205755 DC : DRAFT MAY 2002 | IEC TR 62324. ED.1 - RAMAN GAIN EFFICIENCY MEASUREMENT OF SINGLE-MODE OPTICAL FIBRES USING CONTINUOUS WAVE METHOD - GUIDANCE |
| UNE-EN 60794-2-41:2011 | Optical fibre cables - Part 2-41: Indoor cables - Product specification for simplex and duplex buffered A4 fibres |
| BS EN 60794-1-21:2015 | Optical fibre cables Generic specification. Basic optical cable test procedures. Mechanical tests methods |
| 03/301185 DC : DRAFT JAN 2003 | IEC 60793-2-50 EDITION 2 - OPTICAL FIBRES - PART 2-50: PRODUCTS SPECIFICATION - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| 05/30140924 DC : DRAFT OCT 2005 | IEC 62324 TR - SINGLE-MODE OPTICAL FIBRES - RAMAN GAIN EFFICIENCY MEASUREMENT USING CONTINUOUS WAVE METHOD - GUIDANCE |
| PD IEC/TR 62285:2005 | Application guide for non-linear coefficient measuring methods |
| 06/30153369 DC : DRAFT JULY 2006 | EN 60793-2-20 - OPTICAL FIBRES - PART 2-20: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A2 MULTIMODE FIBRES |
| 09/30201827 DC : 0 | BS EN 60793-2-10 - OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRES |
| BS ISO/IEC 11801-1:2017 | Information technology. Generic cabling for customer premises General requirements |
| 15/30332504 DC : 0 | BS EN 60793-1-45 - OPTICAL FIBRES - PART 1-45: MEASUREMENT METHODS - MODE FIELD DIAMETER MEASUREMENT |
| BS ISO 22902-7:2006 | Road vehicles. Automotive multimedia interface Physical specification |
| BS EN 60793-2-70:2017 | Optical fibres Product specifications. Sectional specification for polarization-maintaining fibres |
| 15/30319951 DC : 0 | BS EN 60794-3-60 - OPTICAL FIBRE CABLES - PART 3-60: OUTDOOR CABLES - FAMILY SPECIFICATION FOR DRINKING WATER PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN / FLOATING INTO DRINK DRINKING WATER PIPES |
| 09/30215019 DC : 0 | BS EN 50551-1 - SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS |
| 13/30286069 DC : 0 | BS EN 60794-3 - OPTICAL FIBRE CABLES - PART 3: SECTIONAL SPECIFICATION - DOOR CABLES |
| 16/30337880 DC : 0 | BS EN 60793-1-47 - OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
| 08/30175854 DC : DRAFT JAN 2008 | IEC 61746-2 ED1 - CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 2: OTDR FOR MULTIMODE FIBRES |
| CEI EN 60793-1-44 : 2012 | OPTICAL FIBRES - PART 1-44: MEASUREMENT METHODS AND TEST PROCEDURES - CUT-OFF WAVELENGTH |
| 16/30334630 DC : 0 | BS EN IEC 60794-1-23 ED 2.0 - OPTICAL FIBRE CABLES - PART 1-23: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - CABLE ELEMENT TEST METHODS |
| BS EN 60793-2-20:2016 | Optical fibres Product specifications. Sectional specification for category A2 multimode fibres |
| 07/30164159 DC : 0 | BS EN 60794-2-30 - OPTICAL FIBRE CABLES - PART 2-30: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR OPTICAL FIBRE RIBBON CABLES |
| 15/30328730 DC : 0 | BS EN 60794-1-22 - OPTICAL FIBRE CABLES - PART 1-22: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - ENVIRONMENTAL TEST METHODS |
| CEI EN 60794-2-41 : 2009 | OPTICAL FIBRE CABLES - PART 2-41: INDOOR CABLES - PRODUCT SPECIFICATION FOR SIMPLEX AND DUPLEX BUFFERED A4 FIBRES |
| CEI EN 50411-2-8 : 2010 | FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-8: MICRODUCT CONNECTORS, FOR AIR BLOWN OPTICAL FIBRES, TYPE 1 |
| BS EN 60794-1-22:2012 | Optical fibre cables Generic specification. Basic optical cable test procedures. Environmental test methods |
| CLC/TS 50429:2005 | Optical fibre cables - Sewer cables - Family specification for cables to be installed in storm and sanitary sewers |
| 09/30206919 DC : 0 | BS EN 3745-301 - AEROSPACE SERIES - FIBRES AND CABLES, OPTICAL, AIRCRAFT USE - TEST METHODS - PART 301: ATTENUATION |
| CEI CLC/TS 50430 : 2005 | OPTICAL FIBRE CABLES - GAS PIPE CABLES - FAMILY SPECIFICATION FOR CABLES TO BE INSTALLED IN HIGH PRESSURE GAS PIPES |
| CEI CLC/TS 50431 : 2005 | OPTICAL FIBRE CABLES - DRINKING WATER PIPE CABLES - FAMILY SPECIFICATION FOR CABLES TO BE INSTALLED IN DRINKING WATER PIPES |
| 02/205756 DC : DRAFT MAY 2002 | IEC 60794-4. ED 2.0 - OPTICAL FIBRE CABLES - PART 4: SECTIONAL SPECIFICATION - AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES |
| 06/30153377 DC : DRAFT JULY 2006 | BS IEC 60793-2-50 - OPTICAL FIBRES - PART 2-50 - PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| BS EN 60793-1-44:2011 | Optical fibres Measurement methods and test procedures. Cut-off wavelength |
| BS IEC 60793-2:1998 | Optical fibres Product specifications |
| BS EN 61280-4-1:2009 | Fibre optic communication subsystem test procedures Installed cable plant. Multimode attenuation measurement |
| SMPTE ST 297-1 : 2015 | SERIAL DIGITAL FIBER TRANSMISSION SYSTEM FOR SMPTE ST 259, SMPTE ST 344, SMPTE ST 292-1/2, SMPTE ST 424, SMPTE ST 2081-1 AND SMPTE ST 2082-1 SIGNALS |
| 07/30164155 DC : 0 | BS EN 60793-2-60 - OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES |
| 15/30332693 DC : 0 | BS EN 60794-2 - OPTICAL FIBRE CABLES - PART 2: INDOOR OPTICAL FIBRE CABLES - SECTIONAL SPECIFICATIONS |
| 14/30296106 DC : 0 | BS EN 60793-2-20 - OPTICAL FIBRES - PART 2-20: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A2 MULTIMODE FIBRES |
| EN IEC 60793-1-45:2018 | Optical fibres - Part 1-45: Measurement methods and test procedures - Mode field diameter |
| CEI EN 61746-1 : 2012 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 1: OTDR FOR SINGLE-MODE FIBRES |
| IEEE 1591.2-2017 | IEEE Standard for Testing and Performance of Hardware for All-Dielectric Self-Supporting (ADSS) Fiber Optic Cable |
| CEI CLC/TS 50429 : 2005 | OPTICAL FIBRE CABLES - SEWER CABLES - FAMILY SPECIFICATION FOR CABLES TO BE INSTALLED IN STORM AND SANITARY SEWERS |
| BS EN 60794-4-10:2014 | Optical fibre cables Family specification. Optical ground wires (OPGW) along electrical power lines |
| 07/30170378 DC : DRAFT AUG 2007 | BS EN 61290-10-1 - OPTICAL AMPLIFIER TEST METHODS - PART 10-1: MULTICHANNEL PARAMETERS - PULSE METHOD USING AN OPTICAL SWITCH AND OPTICAL SPECTRUM ANALYZER |
| CEI EN 60794-1-23 : 2013 | OPTICAL FIBRE CABLES - PART 1-23: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - CABLE ELEMENT TEST METHODS |
| BS EN 60793-2-60:2008 | Optical fibres Product specifications. Sectional specification for category C single-mode intraconnection fibres |
| I.S. EN IEC 60793-1-54:2018 | OPTICAL FIBRES - PART 1-54: MEASUREMENT METHODS AND TEST PROCEDURES - GAMMA IRRADIATION |
| PREN 3745-301 : 200P2 | AEROSPACE SERIES - FIBRES AND CABLES, OPTICAL AIRCRAFT USE - TEST METHODS - PART 301: ATTENUATION |
| I.S. EN 61280-4-2:2014 | FIBRE-OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-2: INSTALLED CABLE PLANT - SINGLE-MODE ATTENUATION AND OPTICAL RETURN LOSS MEASUREMENT |
| I.S. EN 60794-5:2016 | OPTICAL FIBRE CABLES - PART 5: SECTIONAL SPECIFICATION - MICRODUCT CABLING FOR INSTALLATION BY BLOWING |
| I.S. EN 60794-3-70:2016 | OPTICAL FIBRE CABLES - PART 3-70: OUTDOOR CABLES - FAMILY SPECIFICATION FOR OUTDOOR OPTICAL FIBRE CABLES FOR RAPID/MULTIPLE DEPLOYMENT |
| BS EN 50551-1:2011 | Simplex and duplex cables to be used for cords Blank detail specification and minimum requirements |
| NF EN 60794-2-10 : 2011 | OPTICAL FIBRE CABLES - PART 2-10: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES |
| I.S. EN 60793-1-52:2014 | OPTICAL FIBRES - PART 1-52: MEASUREMENT METHODS AND TEST PROCEDURES - CHANGE OF TEMPERATURE TESTS |
| CEI EN 60794-4-20 : 2013 | OPTICAL FIBRE CABLES - PART 4-20: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR ADSS (ALL DIELECTRIC SELF SUPPORTED) OPTICAL CABLES |
| NF EN 50551-1 : 2011 | SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS |
| I.S. CLC TS 50431:2005 | OPTICAL FIBRE CABLES - DRINKING WATER PIPE CABLES - FAMILY SPECIFICATION FOR CABLES TO BE INSTALLED IN DRINKING WATER PIPES |
| ISO/IEC 24702:2006 | Information technology Generic cabling Industrial premises |
| I.S. EN 50551-1:2011 | SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS |
| IEC TR 62285:2005 | Application guide for non-linear coefficient measuring methods |
| OVE/ONORM EN 60794-2-50 : 2009 | OPTICAL FIBRE CABLES - PART 2-50: INDOOR CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES |
| IEC 60793-2-30:2015 | Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres |
| 13/30292530 DC : 0 | BS EN 60793-2-10 ED 5.0 - OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRES |
| EN 60794-3-60:2008 | Optical fibre cables - Part 3-60: Outdoor cables - Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes |
| EN 60793-1-51:2014 | Optical fibres - Part 1-51: Measurement methods and test procedures - Dry heat (steady state) tests |
| IEC 60793-1-47:2017 | Optical fibres - Part 1-47: Measurement methods and test procedures - Macrobending loss |
| EN 60794-1-1:2016 | Optical fibre cables - Part 1-1: Generic specification - General |
| EN 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| EN 60793-1-52:2014 | Optical fibres - Part 1-52: Measurement methods and test procedures - Change of temperature tests |
| IEC 60793-1-54:2018 | Optical fibres - Part 1-54: Measurement methods and test procedures - Gamma irradiation |
| EN 60794-5:2016 | Optical fibre cables - Part 5: Sectional specification - Microduct cabling for installation by blowing |
| EN 60793-2-30:2015 | Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres |
| EN 60794-2-41 : 2008 | OPTICAL FIBRE CABLES - PART 2-41: INDOOR CABLES - PRODUCT SPECIFICATION FOR SIMPLEX AND DUPLEX BUFFERED A4 FIBRES |
| EN 60794-3-50 : 2008 | OPTICAL FIBRE CABLES - PART 3-50: OUTDOOR CABLES - FAMILY SPECIFICATION FOR GAS PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN GAS PIPES |
| EN 61280-4-1:2009 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| EN 60793-1-1:2017 | Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance |
| EN 60793-2-20:2016 | Optical fibres - Part 2-20: Product specifications - Sectional specification for category A2 multimode fibres |
| EN 60794-5-20:2014 | Optical fibre cables - Part 5-20: Family specification - Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
| EN 60794-3:2015 | Optical fibre cables - Part 3: Sectional specification - Outdoor cables |
| EN 61290-1:2015 | Optical amplifiers - Test methods - Part 1: Power and gain parameters |
| EN 60794-1-23:2012 | OPTICAL FIBRE CABLES - PART 1-23: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - CABLE ELEMENT TEST METHODS (IEC 60794-1-23:2012) |
| EN 60793-2-60:2008 | Optical fibres - Part 2-60: Product specifications - Sectional specification for category C single-mode intraconnection fibres |
| EN 60794-2-30:2008 | Optical fibre cables - Part 2-30: Indoor cables - Family specification for ribbon cables |
| EN 60793-1-46:2002 | Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance |
| EN 60794-2-10:2011 | Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for simplex and duplex cables |
| BS EN 61280-4-2:2014 | Fibre-optic communication subsystem test procedures Installed cable plant. Single-mode attenuation and optical return loss measurement |
| 13/30285534 DC : 0 | BS EN 61290-1 - OPTICAL AMPLIFIERS - TEST METHODS - PART 1: OPTICAL POWER AND GAIN PARAMETERS |
| BS EN 60794-5-10:2014 | Optical fibre cables Family specification. Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
| PD IEC/TR 62324:2007 | Single-mode optical fibres. Raman gain efficiency measurement using continuous wave method. Guidance |
| BS EN IEC 60794-1-22:2018 | Optical fibre cables Generic specification. Basic optical cable test procedures. Environmental test methods |
| BS EN 60793-1-47:2009 | Optical fibres Measurement methods and test procedures. Macrobending loss |
| ES 202 319 : 1.1.1 | TRANSMISSION AND MULTIPLEXING (TM); PASSIVE OPTICAL COMPONENTS AND CABLES; OPTICAL FIBRE CABLES TO BE USED FOR PATCHCORD APPLICATIONS FOR SINGLE-MODE OPTICAL FIBRE COMMUNICATION SYSTEMS; COMMON REQUIREMENTS AND CONFORMANCE TESTING |
| 15/30332687 DC : 0 | BS EN 60794-1-2 - OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - CROSS REFERENCE TABLE FOR OPTICAL CABLE TEST PROCEDURES |
| 07/30163858 DC : 0 | BS EN 60794-3-40 - OPTICAL FIBRE CABLES - PART 3-40: OUTDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR SEWER CABLES AND CONDUITS FOR INSTALLATION BY BLOWING AND/OR PULLING IN NON-MAN ACCESSIBLE STORM AND SANITARY SEWERS |
| BIS IS/IEC 60793-1-45 : 2001 | OPTICAL FIBRES - PART 1: MEASUREMENT METHODS AND TEST PROCEDURES - SECTION 45: MODE FIELD DIAMETER |
| I.S. EN 61290-1-2:2006 | OPTICAL AMPLIFIERS - TEST METHODS - PART 1-2: POWER AND GAIN PARAMETERS - ELECTRICAL SPECTRUM ANALYZER METHOD |
| 07/30172537 DC : 0 | BS EN 60794-5-20 - OPTICAL FIBRE CABLES - PART 5-20: FAMILY SPECIFICATION FOR OUTDOOR MICRODUCT FIBRE UNITS, MICRODUCTS AND PROTECTED MICRODUCTS FOR INSTALLATION BY BLOWING |
| 03/309905 DC : DRAFT JUNE 2003 | IEC 60794-3-50 ED.1 - MICRO-CABLES, FIBRE UNITS AND MINI-TUBE SYSTEMS FOR INSTALLATION BY BLOWING TECHNIQUES |
| EN 60794-2:2017 | Optical fibre cables - Part 2: Indoor cables - Sectional specification |
| 08/30175850 DC : DRAFT JAN 2008 | BS IEC 61746-1 - CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 1: OTDR FOR SINGLE-MODE FIBRES |
| BS EN 50411-2-8:2009 | Fibre organisers and closures to be used in optical fibre communication systems. Product specifications Microduct connectors, for air blown optical fibres, Type 1 |
| 09/30211145 DC : 0 | BS EN 60794-1-2 - OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES |
| CEI EN 60793-1-52 : 2014 | OPTICAL FIBRES - PART 1-52: MEASUREMENT METHODS AND TEST PROCEDURES - CHANGE OF TEMPERATURE TESTS |
| 15/30319947 DC : 0 | BS EN 60794-3-50 - OPTICAL FIBRE CABLES - PART 3-50: OUTDOOR CABLES - FAMILY SPECIFICATION FOR GAS PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN/INTO GAS PIPES |
| I.S. EN 60794-1-21:2015 | OPTICAL FIBRE CABLES - PART 1-21: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - MECHANICAL TESTS METHODS |
| 05/30128543 DC : DRAFT JAN 2005 | IEC 60794-3-11 - OPTICAL FIBRE CABLES - PART 3-11: OUTDOOR CABLES - DUCT AND DIRECTLY BURIED OPTICAL TELECOMMUNICATION CABLES - DETAILED SPECIFICATION |
| 13/30286065 DC : 0 | BS EN 60794-5 - OPTICAL FIBRE CABLES - PART 5: SECTIONAL SPECIFICATION - MICRODUCT CABLING FOR INSTALLATION BY BLOWING |
| UNE-EN 60793-1-1:2017 | Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance |
| BS EN 60794-1-20:2014 | Optical fibre cables Generic specification. Basic optical cable test procedures. General and definitions |
| UNE-EN 60793-1-53:2014 | Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests |
| BS EN 187105:2002 | Single mode optical cable (duct/direct buried installation) |
| NF EN 187105 : 2002 | SINGLE-MODE OPTICAL FIBRE CABLE (DUCT/DIRECT BURIED INSTALLATION) |
| NF EN 60794-3-11 : 2011 | OPTICAL FIBRE CABLES - PART 3-11: OUTDOOR CABLES - PRODUCT SPECIFICATION FOR DUCT, DIRECTLY BURIED, AND LASHED AERIAL SINGLE-MODE OPTICAL FIBRE TELECOMMUNICATION CABLES |
| 07/30172946 DC : 0 | BS EN 60793-1-47 IEC 60793-1-47 - OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
| 07/30163866 DC : 0 | BS EN 60794-3-60 - OPTICAL FIBRE CABLES -PART 3-60: OUTDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR DRINKING WATER PIPE CABLES AND SUB-DUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN/FLOATING INTO DRINKING WATER PIPES |
| EN IEC 60793-1-47:2018 | Optical fibres - Part 1-47: Measurement methods and test procedures - Macrobending loss |
| 11/30240648 DC : 0 | BS EN 60794-1-20 - OPTICAL FIBRE CABLES - PART 1-20: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL AND DEFINITIONS |
| 06/30153342 DC : DRAFT JULY 2006 | BS IEC 61746 - CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 1 - OTDR FOR SINGLE-MODE FIBRES |
| BS EN 61290-1-2:2005 | Optical amplifiers. Test methods Power and gain parameters - Electrical spectrum analyzer method |
| 10/30232701 DC : 0 | BS EN 60793-2-50 - OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| BS EN 61746:2005 | Calibration of optical time-domain reflectometers (OTDR) |
| I.S. EN 60794-1-23:2012 | OPTICAL FIBRE CABLES - PART 1-23: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - CABLE ELEMENT TEST METHODS (IEC 60794-1-23:2012 (EQV)) |
| 04/30111264 DC : DRAFT MARCH 2004 | |
| BS EN 60794-2-10:2011 | Optical fibre cables Indoor optical fibre cables. Family specification for simplex and duplex cables |
| CEI EN 50551-2 : 2014 | SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 2: DETAILED SPECIFICATION AND MINIMUM REQUIREMENTS FOR A 3,0 MM SIMPLEX RUGGEDISED SINGLE MODE FIBRE CABLE TO BE USED FOR PATCHCORDS/CORDS CATEGORY U |
| CEI EN 60794-3-60 : 2010 | OPTICAL FIBRE CABLES - PART 3-60: OUTDOOR CABLES - FAMILY SPECIFICATION FOR DRINKING WATER PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING/FLOATING IN DRINKING WATER PIPES |
| CEI EN 61290-1-2 : 2006 | OPTICAL AMPLIFIERS - TEST METHODS - PART 1-2: POWER AND GAIN PARAMETERS - ELECTRICAL SPECTRUM ANALYZER METHOD |
| ISO/IEC 11801-1:2017 | Information technology — Generic cabling for customer premises — Part 1: General requirements |
| CEI EN 60794-2-30 : 2010 | OPTICAL FIBRE CABLES - PART 2-30: INDOOR CABLES - FAMILY SPECIFICATION FOR RIBBON CABLES |
| CEI EN 60794-3-11 : 2012 | OPTICAL FIBRE CABLES - PART 3-11: OUTDOOR CABLES - PRODUCT SPECIFICATION FOR DUCT, DIRECTLY BURIED AND LASHED AERIAL SINGLE-MODE OPTICAL FIBRE TELECOMMUNICATION CABLES |
| I.S. EN IEC 60793-1-47:2018 | OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
| BIS IS/IEC 60793-1-47 : 2009 | OPTICAL FIBRES - PART 1: MEASUREMENT METHODS AND TEST PROCEDURES - SECTION 47: MACROBENDING LOSS |
| I.S. EN 60793-2-10:2017 | OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRE |
| I.S. CLC TS 50430:2005 | OPTICAL FIBRE CABLES - GAS PIPE CABLES - FAMILY SPECIFICATION FOR CABLES TO BE INSTALLED IN HIGH PRESSURE GAS PIPES |
| IEC TR 62221:2012 | Optical fibres - Measurement methods - Microbending sensitivity |
| CEI EN 60794-1-2 : 2014 | OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL GUIDANCE |
| I.S. EN IEC 60794-1-22:2018 | OPTICAL FIBRE CABLES - PART 1-22: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - ENVIRONMENTAL TEST METHODS |
| I.S. EN 50551-2:2013 | SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 2: DETAILED SPECIFICATION AND MINIMUM REQUIREMENTS FOR A 3,0 MM SIMPLEX RUGGEDISED SINGLE MODE FIBRE CABLE TO BE USED FOR PATCHCORDS/CORDS CATEGORY U |
| I.S. EN 60794-2:2017 | OPTICAL FIBRE CABLES - PART 2: INDOOR CABLES - SECTIONAL SPECIFICATION |
| BIS IS/IEC 60793-1-46 : 2001 | OPTICAL FIBRES - PART 1: MEASUREMENT METHODS AND TEST PROCEDURES - SECTION 46: MONITORING OF CHANGES IN OPTICAL TRANSMITTANCE |
| IEC 60794-1-22:2017 | Optical fibre cables - Part 1-22: Generic specification - Basic optical cable test procedures - Environmental test methods |
| I.S. EN 61746-1:2011 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 1: OTDR FOR SINGLE-MODE FIBRES |
| I.S. EN 60794-1-20:2014 | OPTICAL FIBRE CABLES - PART 1-20: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL AND DEFINITIONS |
| UNE-EN 60794-2-30:2011 | Optical fibre cables - Part 2-30: Indoor cables - Family specification for ribbon cables |
| NF EN 60794-1-1 : 2002 | OPTICAL FIBER CABLES - PART 1-1: GENERIC SPECIFICATION - GENERAL |
| I.S. EN 60794-1-2:2017 | OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL GUIDANCE |
| ISO/IEC 14165-115:2006 | Information technology Fibre Channel Part 115: Physical Interfaces (FC-PI) |
| IEC 61280-4-1:2009 | Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement |
| 17/30345069 DC : 0 | BS EN 60793-2-10 - OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRES |
| IEC 60794-5:2014 | Optical fibre cables - Part 5: Sectional specification - Microduct cabling for installation by blowing |
| BS EN 3745-301:2012 | Aerospace series. Fibres and cables, optical, aircraft use. Test methods Attenuation |
| IEC 60793-1-45:2017 | Optical fibres - Part 1-45: Measurement methods and test procedures - Mode field diameter |
| I.S. EN 3745-301:2012 | AEROSPACE SERIES - FIBRES AND CABLES, OPTICAL, AIRCRAFT USE - TEST METHODS - PART 301: ATTENUATION |
| EN 60794-1-2:2017/AC:2017-07 | OPTICAL FIBRE CABLES - PART 1-2: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL GUIDANCE (IEC 60794-1-2:2017) |
| EN 61290-1-3:2015 | Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method |
| 11/30240652 DC : 0 | BS EN 60794-1-21 - OPTICAL FIBRE CABLES - PART 1-21: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - MECHANICAL TESTS METHODS |
| 08/30178186 DC : DRAFT FEB 2008 | BS EN 60794-5-10 - OPTICAL FIBRE CABLES - PART 5-10: FAMILY SPECIFICATION FOR OUTDOOR MICRODUCT OPTICAL FIBRE CABLES, MICRODUCTS AND PROTECTED MICRODUCTS FOR INSTALLATION BY BLOWING |
| BS EN 60794-2-50:2008 | Optical fibre cables Indoor cables. Family specification for simplex and duplex cables for use in terminated cable assemblies |
| 13/30279735 DC : 0 | BS EN 60793-1-53 - OPTICAL FIBRES - PART 1-53: MEASUREMENT METHODS AND TEST PROCEDURES - WATER IMMERSION |
| BS EN 60793-1-53:2014 | Optical fibres Measurement methods and test procedures. Water immersion tests |
| BS EN 60794-3-70:2016 | Optical fibre cables Outdoor cables. Family specification for outdoor optical fibre cables for rapid/multiple deployment |
| BS EN 60794-2:2017 | Optical fibre cables Indoor cables. Sectional specification |
| UNE-EN 60794-1-20:2014 | Optical fibre cables - Part 1-20: Generic specification - Basic optical cable test procedures - General and definitions |
| BS EN 60794-3-40:2008 | Optical fibre cables Outdoor cables. Family specification for sewer cables and conduits for installation by blowing and/or pulling in non-man accessible storm and sanitary sewers |
| 04/30115140 DC : DRAFT JUN 2004 | IEC 60794-5 - OPTICAL FIBRE CABLES - PART 5: SECTIONAL SPECIFICATION FOR MICRODUCT CABLING FOR INSTALLATION BY BLOWING |
| NF EN 60793-1-51 : 2014 | OPTICAL FIBRES - PART 1-51: MEASUREMENT METHODS AND TEST PROCEDURES - DRY HEAT (STEADY STATE) TESTS |
| CEI EN 60794-5-20 : 2014 | OPTICAL FIBRE CABLES - PART 5-20: FAMILY SPECIFICATION - OUTDOOR MICRODUCT FIBRE UNITS, MICRODUCTS AND PROTECTED MICRODUCTS FOR INSTALLATION BY BLOWING |
| CEI EN 61280-4-1 : 2011 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| CEI EN 50551-1 : 2012 | SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS |
| BS IEC/IEEE 62582-5:2015 | Nuclear power plants. Instrumentation and control important to safety. Electrical equipment condition monitoring methods Optical time domain reflectometry |
| BS EN 60794-2-42:2008 | Optical fibre cables Indoor optical fibre cables. Product specification for simplex and duplex cables with A4 fibres |
| NF EN 60793-2-40 : 2017 | OPTICAL FIBRES - PART 2-40: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A4 MULTIMODE FIBRES |
| 06/30153345 DC : DRAFT JULY 2006 | BS IEC 61746-2 - CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 2 - OTDR FOR MULTIMODE FIBRES |
| 14/30310028 DC : 0 | BS EN 60794-1-1 - OPTICAL FIBRE CABLES - PART 1-1: GENERIC SPECIFICATION - GENERAL |
| I.S. EN 60794-4-10:2014 | OPTICAL FIBRE CABLES - PART 4-10: FAMILY SPECIFICATION - OPTICAL GROUND WIRES (OPGW) ALONG ELECTRICAL POWER LINES |
| 13/30292880 DC : 0 | BS EN 60794-3-70 - OPTICAL FIBRE CABLES - PART 3.70: FAMILY SPECIFICATION FOR OUTDOOR OPTICAL FIBRE CABLES FOR RAPID/MULTIPLE DEPLOYMENT |
| UNE-EN 60793-1-51:2014 | Optical fibres - Part 1-51: Measurement methods and test procedures - Dry heat (steady state) tests |
| BIS IS/IEC 60793-1-1 : 2008 | OPTICAL FIBRES - PART 1: MEASUREMENT METHODS AND TEST PROCEDURES - SECTION 1: GENERAL AND GUIDANCE |
| I.S. EN 50173-1:2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| 16/30338299 DC : 0 | BS EN 60793-2-70 - OPTICAL FIBRES - PART 2-70: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATIONS FOR POLARIZATION-MAINTAINING FIBRES |
| 11/30243236 DC : 0 | BS EN 60793-2-30 - OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| 02/206898 DC : DRAFT JULY 2002 | IEC 60793-1-54 ED.1 - OPTICAL FIBRES - PART 1-54: MEASUREMENT METHODS AND TEST PROCEDURES - GAMMA IRRADIATION |
| CEI EN 61280-4-2 : 2015 | FIBRE-OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-2: INSTALLED CABLE PLANT - SINGLE-MODE ATTENUATION AND OPTICAL RETURN LOSS MEASUREMENT |
| BS EN 60793-1-1:2017 | Optical fibres Measurement methods and test procedures. General and guidance |
| 04/30110918 DC : DRAFT MAR 2004 | IEC 61290-1-2 ED 2.0 - OPTICAL AMPLIFIER TEST METHODS - PART 1-2: OPTICAL POWER AND GAIN PARAMETERS - ELECTRICAL SPECTRUM ANALYZER METHOD |
| BS EN 60793-2-30:2015 | Optical fibres Product specifications. Sectional specification for category A3 multimode fibres |
| BS EN 60794-3-60:2008 | Optical fibre cables Outdoor cables. Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes |
| BS EN 60793-2-50:2016 | Optical fibres Product specifications. Sectional specification for class B single-mode fibres |
| UNE-EN 60793-1-52:2014 | Optical fibres - Part 1-52: Measurement methods and test procedures - Change of temperature tests |
| UNE-EN 60793-1-50:2015 | Optical fibres - Part 1-50: Measurement methods - Damp heat (steady state) tests |
| ISO 22902-7:2006 | Road vehicles Automotive multimedia interface Part 7: Physical specification |
| I.S. EN 60793-1-47:2009 | OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
| I.S. EN 60793-1-51:2014 | OPTICAL FIBRES - PART 1-51: MEASUREMENT METHODS AND TEST PROCEDURES - DRY HEAT (STEADY STATE) TESTS |
| NF EN 60793-2-50 : 2017 | OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| BS EN 50173-1:2011 | Information technology. Generic cabling systems General requirements |
| I.S. EN 60793-2-70:2017 | OPTICAL FIBRES - PART 2-70: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR POLARIZATION-MAINTAINING FIBRES |
| BS EN 60794-4-20:2012 | Optical fibre cables Aerial optical cables along electrical power lines. Family specification for ADSS (All Dielectric Self Supported) optical cables |
| I.S. EN 60794-3:2002 | OPTICAL FIBRE CABLES - PART 3: SECTIONAL SPECIFICATION - OUTDOOR CABLES |
| I.S. EN 60794-2-50:2008 | OPTICAL FIBRE CABLES - PART 2-50: INDOOR CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES |
| I.S. EN 60794-2-10:2011 | OPTICAL FIBRE CABLES - PART 2-10: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES (IEC 60794-2-10:2011 (EQV)) |
| I.S. EN 60794-5-20:2014 | OPTICAL FIBRE CABLES - PART 5-20: FAMILY SPECIFICATION - OUTDOOR MICRODUCT FIBRE UNITS, MICRODUCTS AND PROTECTED MICRODUCTS FOR INSTALLATION BY BLOWING |
| I.S. EN 61290-1-3:2015 | OPTICAL AMPLIFIERS - TEST METHODS - PART 1-3: POWER AND GAIN PARAMETERS - OPTICAL POWER METER METHOD |
| CEI EN 60793-2-60 : 2009 | OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES |
| I.S. EN 60793-2-50:2016 | OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| CEI EN 60794-2-10 : 2012 | OPTICAL FIBRE CABLES - PART 2-10: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES |
| CEI EN 60793-2-70 : 1ED 2017 | OPTICAL FIBRES - PART 2-70: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR POLARIZATION-MAINTAINING FIBRES |
| CEI EN 60793-2-30 : 2016 | OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| IEC TR 62283:2010 | Optical fibres - Guidance for nuclear radiation tests |
| EN 50173-1:2011 | Information technology - Generic cabling systems - Part 1: General requirements |
| I.S. EN 60794-3-40:2008 | OPTICAL FIBRE CABLES - PART 3-40: OUTDOOR CABLES - FAMILY SPECIFICATION FOR SEWER CABLES AND CONDUITS FOR INSTALLATION BY BLOWING AND/OR PULLING IN NON-MAN ACCESSIBLE STORM AND SANITARY SEWERS |
| ISO/IEC 11801:2002 | Information technology Generic cabling for customer premises |
| IEC 60793-2-10:2017 | Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres |
| IEC 60794-2-50:2008 | Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies |
| IEC 60793-1-1:2017 | Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance |
| IEC 60794-2-10:2011 | Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for simplex and duplex cables |
| IEC 60794-1-1:2015 RLV | Optical fibre cables - Part 1-1: Generic specification - General |
| UNI EN 3745-301 : 2012 | AEROSPACE SERIES - FIBRES AND CABLES, OPTICAL, AIRCRAFT USE - TEST METHODS - PART 301: ATTENUATION |
| IEC 60793-1-47:2017 RLV | Optical fibres - Part 1-47: Measurement methods and test procedures - Macrobending loss |
| 10/30240050 DC : DRAFT DEC 2010 | BS EN 61280-4-2 - FIBRE-OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-2: INSTALLED CABLE PLANT - SINGLEMODE ATTENUATION AND OPTICAL RETURN LOSS MEASUREMENT |
| 05/30134653 DC : DRAFT JUN 2005 | IEC 60793-2-10 ED 3 - OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRES |
| BS EN 60793-1-52:2014 | Optical fibres Measurement methods and test procedures. Change of temperature tests |
| CEI EN 60794-2-42 : 2009 | OPTICAL FIBRE CABLES - PART 2-42: INDOOR OPTICAL FIBRE CABLES - PRODUCT SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES WITH A4 FIBRES |
| 15/30321396 DC : DRAFT FEB 2015 | BS EN 60794-2-30 - OPTICAL FIBRE CABLES - PART 2-30: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR OPTICAL FIBRE RIBBON CABLES |
| EN IEC 60794-1-22:2018 | Optical fibre cables - Part 1-22: Generic specification - Basic optical cable test procedures - Environmental test methods |
| 11/30240656 DC : 0 | BS EN 60794-1-22 - OPTICAL FIBRE CABLES - PART 1-22: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - ENVIRONMENTAL TESTS METHODS |
| PD IEC/TR 62283:2010 | Optical fibres. Guidance for nuclear radiation tests |
| CEI EN 61746-2 : 2012 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 2: OTDR FOR MULTIMODE FIBRES |
| 02/203732 DC : DRAFT MAR 2002 | IEC TR 62316. ED.1 - GUIDANCE FOR THE INTERPRETATION OF OTDR BACKSCATTERING TRACES |
| NF EN 60794-2-50 : 2009 | OPTICAL FIBRE CABLES - PART 2-50: INDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES |
| 02/205753 DC : DRAFT AUG 2002 | IEC 60793-2-10 ED.2.0 - FIBRE AND CABLES - PART 2-10: PRODUCT SPECIFICATION - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRES |
| CEI EN 60794-3-40 : 2010 | OPTICAL FIBRE CABLES - PART 3-40: OUTDOOR CABLES - FAMILY SPECIFICATION FOR SEWER CABLES AND CONDUITS FOR INSTALLATION BY BLOWING AND/OR PULLING IN NON-MAN ACCESSIBLE STORM AND SANITARY SEWERS |
| 12/30261347 DC : 0 | BS EN 50582 - METHOD OF TEST FOR RESISTANCE TO FIRE OF UNPROTECTED OPTICAL FIBRE CABLES FOR USE IN EMERGENCY CIRCUITS (DIAMETER LESS THAN OR EQUAL TO 20 MM) |
| 13/30272041 DC : 0 | BS EN 60793-2-40 - OPTICAL FIBRES - PART 40: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A4 MULTIMODE FIBRES |
| UNE-EN 60794-5:2012 | Optical fibre cables - Part 5: Sectional specification - Microduct cabling for installation by blowing |
| 15/30326655 DC : 0 | BS EN 61280-4-1 - FIBRE-OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| CEI EN 60794-2-50 : 2010 | OPTICAL FIBRE CABLES - PART 2-50: INDOOR CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES |
| CEI EN 60793-1-51 : 2014 | OPTICAL FIBRES - PART 1-51: MEASUREMENT METHODS AND TEST PROCEDURES - DRY HEAT (STEADY STATE) TESTS |
| 13/30279729 DC : 0 | BS EN 60793-1-52 - OPTICAL FIBRES - PART 1-52: MEASUREMENT METHODS AND TEST PROCEDURES - CHANGE OF TEMPERATURE |
| 14/30315980 DC : 0 | BS EN 60794-2-22 - OPTICAL FIBRE CABLES - PART 2-22: INDOOR OPTICAL FIBRE CABLES - DETAIL SPECIFICATION FOR MULTI-SIMPLEX BREAKOUT OPTICAL CABLES TO BE TERMINATED WITH CONNECTORS |
| BS EN 61746-2:2011 | Calibration of optical time-domain reflectometers (OTDR) OTDR for multimode fibres |
| 14/30189466 DC : 0 | BS IEC/IEEE 62582-5 ED 1.0 - NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - ELECTRICAL EQUIPMENT CONDITION MONITORING METHODS - PART 5: OPTICAL TIME DOMAIN REFLECTOMETRY |
| 14/30310858 DC : 0 | BS EN 60794-4-20 - OPTICAL FIBRE CABLES - PART 4-20: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR ADSS (ALL DIELECTRIC SELF SUPPORTED) OPTICAL CABLES |
| BS EN 61290-1:2015 | Optical amplifiers. Test methods Power and gain parameters |
| 08/30174652 DC : DRAFT SEP 2008 | BS EN 60793-2-40 - OPTICAL FIBRES - PART 40: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A4 MULTIMODE FIBRES |
| I.S. EN 50411-2-8:2009 | FIBRE ORGANISERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 2-8: MICRODUCT CONNECTORS, FOR AIR BLOWN OPTICAL FIBRES, TYPE 1 |
| I.S. EN 60794-5-10:2014 | OPTICAL FIBRE CABLES - PART 5-10: FAMILY SPECIFICATION - OUTDOOR MICRODUCT OPTICAL FIBRE CABLES, MICRODUCTS AND PROTECTED MICRODUCTS FOR INSTALLATION BY BLOWING |
| BS EN 60794-3-50:2008 | Optical fibre cables Outdoor cables. Family specification for gas pipe cables and subducts for installation by blowing and/or pulling/dragging in gas pipes |
| 13/30279650 DC : 0 | BS EN 60793-1-50 - OPTICAL FIBRES - PART 1-50: MEASUREMENT METHODS AND TEST PROCEDURES - DAMP HEAT (STEADY STATE) |
| BS EN 60794-3-11:2010 | Optical fibre cables Outdoor cables. Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables |
| BS EN 60794-2-30:2008 | Optical fibre cables Indoor cables. Family specification for ribbon cables |
| 10/30240040 DC : DRAFT DEC 2010 | BS EN 60793-1-54 - OPTICAL FIBRES - PART 1-54: MEASUREMENT METHODS AND TEST PROCEDURES - GAMMA IRRADIATION |
| CEI EN 60793-1-1 : 2010 | OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE |
| 17/30365105 DC : 0 | BS EN 60793-2-50 ED.6.0 - OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| 11/30240660 DC : 0 | BS EN 60794-1-23 - OPTICAL FIBRE CABLES - PART 1-23: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - CABLE ELEMENTS TESTS METHODS |
| CEI EN 60793-1-47 : 2010 | OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
| CEI EN 60793-1-54 : 2013 | OPTICAL FIBRES - PART 1-54: MEASUREMENT METHODS AND TEST PROCEDURES - GAMMA IRRADIATION |
| BS EN 60793-1-50:2015 | Optical fibres Measurement methods. Damp heat (steady state) tests |
| BS EN 60793-1-46:2002 | Optical fibres. Measurement methods and test procedures Monitoring of changes in optical transmittance |
| PD IEC/TR 62316:2017 | Guidance for the interpretation of OTDR backscattering traces for single-mode fibres |
| BS EN 60793-1-54 : 2018 | OPTICAL FIBRES - PART 1-54: MEASUREMENT METHODS AND TEST PROCEDURES - GAMMA IRRADIATION |
| 16/30325971 DC : 0 | BS ISO/IEC 11801-1 - INFORMATION TECHNOLOGY - GENERIC CABLING FOR CUSTOMER PREMISES - PART 1: GENERAL REQUIREMENTS |
| 17/30365109 DC : 0 | BS EN 60793-1-32 ED.3.0 - OPTICAL FIBRES - PART 1-32: MEASUREMENT METHODS AND TEST PROCEDURES - COATING STRIPPABILITY |
| UNE-EN 60794-1-1:2016 | Optical fibre cables - Part 1-1: Generic specification - General |
| CEI EN 50173-1 : 2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| BS EN 60793-1-51:2014 | Optical fibres Measurement methods and test procedures. Dry heat (steady state) tests |
| BS EN 60793-2-40:2016 | Optical fibres Product specifications. Sectional specification for category A4 multimode fibres |
| CSA ISO/IEC 14165-115 : 2006 | INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 115: PHYSICAL INTERFACES (FC-PI) |
| I.S. EN 61280-4-1:2009 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| I.S. EN 60794-4-20:2012 | OPTICAL FIBRE CABLES - PART 4-20: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR ADSS (ALL DIELECTRIC SELF SUPPORTED) OPTICAL CABLES (IEC 60794-4-20:2012 (EQV)) |
| I.S. EN 60794-3-50:2008 | OPTICAL FIBRE CABLES - PART 3-50: OUTDOOR CABLES - FAMILY SPECIFICATION FOR GAS PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN GAS PIPES |
| I.S. EN 60793-2-30:2015 | OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| I.S. EN 60793-2-60:2008 | OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES |
| CLC/TS 50431:2005 | Optical fibre cables - Drinking water pipe cables - Family specification for cables to be installed in drinking water pipes |
| CEI EN 60794-5-10 : 2014 | OPTICAL FIBRE CABLES - PART 5-10: FAMILY SPECIFICATION - OUTDOOR MICRODUCT OPTICAL FIBRE CABLES, MICRODUCTS AND PROTECTED MICRODUCTS FOR INSTALLATION BY BLOWING |
| EN 60793-2-10:2017 | Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres |
| BS EN 60793-2-10:2017 | Optical fibres Product specifications. Sectional specification for category A1 multimode fibres |
| CEI EN 60794-3-50 : 2010 | OPTICAL FIBRE CABLES - PART 3-50: OUTDOOR CABLES - FAMILY SPECIFICATION FOR GAS PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN GAS PIPES |
| I.S. EN 60794-3-11:2010 | OPTICAL FIBRE CABLES - PART 3-11: OUTDOOR CABLES - PRODUCT SPECIFICATION FOR DUCT, DIRECTLY BURIED AND LASHED AERIAL SINGLE-MODE OPTICAL FIBRE TELECOMMUNICATION CABLES |
| IEC TR 62324:2007 | Single-mode optical fibres - Raman gain efficiency measurement using continuous wave method - Guidance |
| I.S. EN 61746-2:2011 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 2: OTDR FOR MULTIMODE FIBRES |
| I.S. EN 60794-1-1:2016 | OPTICAL FIBRE CABLES - PART 1-1: GENERIC SPECIFICATION - GENERAL |
| I.S. EN 60793-1-45:2004 | OPTICAL FIBRES - PART 1-45: MEASUREMENT METHODS AND TEST PROCEDURES - MODE FIELD DIAMETER |
| EN 61746-1:2011/AC:2014 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 1: OTDR FOR SINGLE-MODE FIBRES (IEC 61746-1:2009) |
| EN 61746-2:2011/AC:2014 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) - PART 2: OTDR FOR MULTIMODE FIBRES |
| IEC 60793-2-40:2015 | Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres |
| IEC 60793-2-60:2008 | Optical fibres - Part 2-60: Product specifications - Sectional specification for category C single-mode intraconnection fibres |
| IEC 60794-3-70:2016 | Optical fibre cables - Part 3-70: Outdoor cables - Family specification for outdoor optical fibre cables for rapid/multiple deployment |
| IEC 60794-1-21:2015 | Optical fibre cables - Part 1-21: Generic specification - Basic optical cable test procedures - Mechanical tests methods |
| IEC 60794-3-60:2008 | Optical fibre cables - Part 3-60: Outdoor cables - Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes |
| IEC 60794-1-2:2017 | Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance |
| IEC 60794-4-10:2014 | Optical fibre cables - Part 4-10: Family specification - Optical ground wires (OPGW) along electrical power lines |
| IEC 60794-3-40:2008 | Optical fibre cables - Part 3-40: Outdoor cables - Family specification for sewer cables and conduits for installation by blowing and/or pulling in non-man accessible storm and sanitary sewers |
| IEC 61746-1:2009 | Calibration of optical time-domain reflectometers (OTDR) - Part 1: OTDR for single mode fibres |
| EN 60794-2-50 : 2008 | OPTICAL FIBRE CABLES - PART 2-50: INDOOR CABLES - FAMILY SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES FOR USE IN TERMINATED CABLE ASSEMBLIES |
| IEC 60793-1-46:2001 | Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance |
| IEC 60794-5-20:2014 | Optical fibre cables - Part 5-20: Family specification - Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
| IEC 60794-3:2014 | Optical fibre cables - Part 3: Outdoor cables - Sectional specification |
| IEC 60793-1-53:2014 | Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests |
| IEC 60794-5-10:2014 | Optical fibre cables - Part 5-10: Family specification - Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
| IEC 60793-2-50:2015 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| IEC 61746:2005 | Calibration of optical time-domain reflectometers (OTDR) |
| IEC 61290-1-3:2015 | Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method |
| IEC 60794-2-42:2008 | Optical fibre cables - Part 2-42: Indoor optical fibre cables - Product specification for simplex and duplex cables with A4 fibres |
| IEC 60794-3-50:2008 | Optical fibre cables - Part 3-50: Outdoor cables - Family specification for gas pipe cables and subducts for installation by blowing and/or pulling/dragging in gas pipes |
| IEC 60794-2-41:2008 | Optical fibre cables - Part 2-41: Indoor cables - Product specification for simplex and duplex buffered A4 fibres |
| IEC 60793-1-51:2014 | Optical fibres - Part 1-51: Measurement methods and test procedures - Dry heat (steady state) tests |
| IEC 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| EN 60794-1-21:2015 | Optical fibre cables - Part 1-21: Generic specification - Basic optical cable test procedures - Mechanical tests methods |
| IEC 60793-1-44:2011 | Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength |
| IEC 60793-1-50:2014 | Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests |
| UNE-EN 60794-1-2:2017 | Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance |
| IEC 61290-1-2:2005 | Optical amplifiers - Test methods - Part 1-2: Power and gain parameters - Electrical spectrum analyzer method |
| IEC 60794-1-23:2012 | Optical fibre cables - Part 1-23: Generic specification - Basic optical cable test procedures - Cable element test methods |
| IEC 60793-1-52:2014 | Optical fibres - Part 1-52: Measurement methods and test procedures - Change of temperature tests |
| EN 60794-4-10:2014 | Optical fibre cables - Part 4-10: Family specification - Optical ground wires (OPGW) along electrical power lines |
| EN 3745-301:2012 | Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 301: Attenuation |
| EN 60793-2-40:2016 | Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres |
| CLC/TS 50430:2005 | Optical fibre cables - Gas pipe cables - Family specification for cables to be installed in high pressure gas pipes |
| 06/30151382 DC : DRAFT JUN 2006 | BS ISO/IEC 24702 - INFORMATION TECHNOLOGY - GENERIC CABLING - INDUSTRIAL PREMISES |
| BIS IS/IEC 60794-1-1 : 2001 | OPTICAL FIBRE CABLES - PART 1: GENERIC SPECIFICATION - SECTION 1: GENERAL |
| BS EN 60794-5:2016 | Optical fibre cables Sectional specification. Microduct cabling for installation by blowing |
| BS EN IEC 60793-1-47:2018 | Optical fibres Measurement methods and test procedures. Macrobending loss |
| NF EN 60793-1-45 : 2004 | OPTICAL FIBERS - PART 1-45: MEASUREMENT METHODS AND TEST PROCEDURES - MODE FIELD DIAMETER |
| 05/30128522 DC : DRAFT JAN 2005 | IEC 60793-1-47 - OPTICAL FIBRES - PART 1-47: MEASUREMENT METHODS AND TEST PROCEDURES - MACROBENDING LOSS |
| BS EN 61746-1:2011 | Calibration of optical time-domain reflectometers (OTDR) OTDR for single-mode fibres |
| 15/30320892 DC : 0 | BS EN 60794-4 - OPTICAL FIBRE CABLES - PART 4: SECTIONAL SPECIFICATION - AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES |
| BS EN 50551-2:2013 | Simplex and duplex cables to be used for cords Detailed specification and minimum requirements for a 3,0 mm simplex ruggedised single mode fibre cable to be used for patchcords/cords category U |
| 13/30286685 DC : 0 | BS EN 60793-2-50 ED 5.0 - OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES |
| BS EN 60794-1-23:2012 | Optical fibre cables Generic specification. Basic optical cable test procedures. Cable element test methods |
| UNE-EN 60794-1-22:2015 | Optical fibre cables - Part 1-22: Generic specification - Basic optical cable test procedures - Environmental test methods |
| CEI EN 60793-1-53 : 2014 | OPTICAL FIBRES - PART 1-53: MEASUREMENT METHODS AND TEST PROCEDURES - WATER IMMERSION TESTS |
| BS EN 60794-1-2:2017 | Optical fibre cables Generic specification. Basic optical cable test procedures. General guidance |
| 13/30279654 DC : 0 | BS EN 60793-1-51 - OPTICAL FIBRES - PART 1-51: MEASUREMENT METHODS AND TEST PROCEDURES - DRY HEAT (STEADY STATE) |
| 03/320270 DC : DRAFT DEC 2003 | IEC 60794-4-10 ED.1 - OPTICAL FIBRE CABLES - PART 4-10: FAMILY SPECIFICATION - OPGW (OPTICAL GROUND WIRES) ALONG ELECTRICAL POWER LINES |
| 04/30109519 DC : DRAFT FEB 2004 | |
| BS EN 61290-1-3:2015 | Optical amplifiers. Test methods Power and gain parameters. Optical power meter method |
| CEI EN 60794-1-22 : 2013 | OPTICAL FIBRE CABLES - PART 1-22: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - ENVIRONMENTAL TEST METHODS |
| BS EN 60793-1-22:2002 | Optical fibres. Measurement methods and test procedures Length measurement - Section 22: Length measurement methods |
| I.S. EN 60794-2-42:2008 | OPTICAL FIBRE CABLES - PART 2-42: INDOOR OPTICAL FIBRE CABLES - PRODUCT SPECIFICATION FOR SIMPLEX AND DUPLEX CABLES WITH A4 FIBRES |
| BIS IS/IEC 60793-1-44 : 2011 | OPTICAL FIBRES - PART 1: MEASUREMENT METHODS AND TEST PROCEDURES - SECTION 44: CUT-OFF WAVELENGTH |
| 14/30296100 DC : 0 | BS EN 61290-1-3 - OPTICAL AMPLIFIERS - TEST METHODS - PART 1-3: OPTICAL POWER AND GAIN PARAMETERS - OPTICAL POWER METER METHOD |
| EN 60794-3-70:2016 | Optical fibre cables - Part 3-70: Outdoor cables - Family specification for outdoor optical fibre cables for rapid/multiple deployment |
| 09/30197559 DC : 0 | BS EN 60794-3-11 ED.2 - OPTICAL FIBRE CABLES - PART 3-11: OUTDOOR CABLES - PRODUCT SPECIFICATION FOR DUCT AND DIRECTLY BURIED SINGLE-MODE OPTICAL FIBRE TELECOMMUNICATION CABLES |
| 07/30163862 DC : 0 | BS EN 60794-3-50 - OPTICAL FIBRE CABLES - PART 3-50: OUTDOOR OPTICAL FIBRE CABLES - FAMILY SPECIFICATION FOR GAS PIPE CABLES AND SUB-DUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING IN/INTO GAS PIPES |
| 13/30292534 DC : 0 | BS EN 60794-4-10 ED 2.0 - OPTICAL FIBRE CABLES - PART 4-10: FAMILY SPECIFICATION - OPGW (OPTICAL GROUND WIRES) ALONG ELECTRICAL POWER LINES |
| 16/30334639 DC : 0 | BS EN 60793-1-1 ED 4.0 - OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE |
| BS EN 60794-5-20:2014 | Optical fibre cables Family specification. Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
| UNE-EN 60794-1-23:2013 | Optical fibre cables - Part 1-23: Generic specification - Basic optical cable test procedures - Cable element test methods |
| EN 60793-2-70:2017 | Optical fibres - Part 2-70: Product specifications - Sectional specification for polarization-maintaining fibres |
| EN IEC 60793-1-54:2018 | Optical fibres - Part 1-54: Measurement methods and test procedures - Gamma irradiation |
| I.S. EN 60793-1-44:2011 | OPTICAL FIBRES - PART 1-44: MEASUREMENT METHODS AND TEST PROCEDURES - CUT-OFF WAVELENGTH |
| NF EN 60794-4-10 : 2007 | OPTICAL FIBRE CABLES - PART 4-10: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR OPGW (OPTICAL GROUND WIRES) |
| 06/30153373 DC : DRAFT JULY 2006 | BS EN 60793-2-30 - OPTICAL FIBRES - PART 2-30 - PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES |
| BS EN 60793-1-45:2003 | Optical fibres Measurement methods and test procedures - Mode field diameter |
| IEC TR 62316:2007 | Guidance for the interpretation of OTDR backscattering traces |
| BS EN 60794-2-41:2008 | Optical fibre cables Indoor cables. Product specification for simplex and duplex buffered A4 fibres |
| CAN/CSA-ISO/IEC 14165-115:2006(R2016) | INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 115: PHYSICAL INTERFACES (FC-PI) |
| NF EN 60793-1-52 : 2014 | OPTICAL FIBRES - PART 1-52: MEASUREMENT METHODS AND TEST PROCEDURES - CHANGE OF TEMPERATURE TESTS |
| I.S. EN 60794-2-41:2008 | OPTICAL FIBRE CABLES - PART 2-41: INDOOR CABLES - PRODUCT SPECIFICATION FOR SIMPLEX AND DUPLEX BUFFERED A4 FIBRES |
| I.S. EN 60793-1-50:2015 | OPTICAL FIBRES - PART 1-50: MEASUREMENT METHODS - DAMP HEAT (STEADY STATE) TESTS |
| CEI EN 60794-5 : 2008 | OPTICAL FIBRE CABLES - PART 5: SECTIONAL SPECIFICATION - MICRODUCT CABLING FOR INSTALLATION BY BLOWING |
| I.S. EN 60794-2-30:2008 | OPTICAL FIBRE CABLES - PART 2-30: INDOOR CABLES - FAMILY SPECIFICATION FOR RIBBON CABLES |
| I.S. EN 60794-1-22:2012 | OPTICAL FIBRE CABLES - PART 1-22: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - ENVIRONMENTAL TEST METHODS (IEC 60794-1-22:2012 (EQV)) |
| BS EN 60794-1-1:2016 | Optical fibre cables Generic specification. General |
| PD IEC/TR 62221:2012 | Optical fibres. Measurement methods. Microbending sensitivity |
| I.S. EN 61290-1:2015 | OPTICAL AMPLIFIERS - TEST METHODS - PART 1: POWER AND GAINPARAMETERS |
| NF EN 60793-1-53 : 2014 | OPTICAL FIBRES - PART 1-53: MEASUREMENT METHODS AND TEST PROCEDURES - WATER IMMERSION TESTS |
| I.S. EN IEC 60793-1-45:2018 | OPTICAL FIBRES - PART 1-45: MEASUREMENT METHODS AND TEST PROCEDURES - MODE FIELD DIAMETER |
| BS EN 60794-3:2015 | Optical fibre cables Sectional specification. Outdoor cables |
| IEC 60793-1-1:2017 RLV | Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance |
| I.S. EN 60793-2-40:2016 | OPTICAL FIBRES - PART 2-40: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A4 MULTIMODE FIBRES |
| IEC 60793-1-45:2017 RLV | Optical fibres - Part 1-45: Measurement methods and test procedures - Mode field diameter |
| I.S. CLC TS 50429:2005 | OPTICAL FIBRE CABLES - SEWER CABLES - FAMILY SPECIFICATION FOR CABLES TO BE INSTALLED IN STORM AND SANITARY SEWERS |
| IEC 60794-2:2017 | Optical fibre cables - Part 2: Indoor cables - Sectional specification |
| I.S. EN 60793-1-1:2017 | OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE |
| IEC 60794-2-30:2008 | Optical fibre cables - Part 2-30: Indoor cables - Family specification for ribbon cables |
| I.S. EN 60793-1-54:2013 | OPTICAL FIBRES - PART 1-54: MEASUREMENT METHODS AND TEST PROCEDURES - GAMMA IRRADIATION (IEC 60793-1-54:2012 (EQV)) |
| I.S. EN 60793-1-53:2014 | OPTICAL FIBRES - PART 1-53: MEASUREMENT METHODS AND TEST PROCEDURES - WATER IMMERSION TESTS |
| I.S. EN 61746:2005 | CALIBRATION OF OPTICAL TIME-DOMAIN REFLECTOMETERS (OTDR) |
| I.S. EN 60794-3-60:2008 | OPTICAL FIBRE CABLES - PART 3-60: OUTDOOR CABLES - FAMILY SPECIFICATION FOR DRINKING WATER PIPE CABLES AND SUBDUCTS FOR INSTALLATION BY BLOWING AND/OR PULLING/DRAGGING/FLOATING IN DRINKING WATER PIPES |
| IEC 60793-1-22:2001 | Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement |
| IEC 60794-1-1:2015 | Optical fibre cables - Part 1-1: Generic specification - General |
| IEC 60793-2-20:2015 | Optical fibres - Part 2-20: Product specifications - Sectional specification for category A2 multimode fibres |
| IEC 61290-1:2014 | Optical amplifiers - Test methods - Part 1: Power and gain parameters |
| IEC 61746-2:2010 | Calibration of optical time-domain reflectometers (OTDR) - Part 2: OTDR for multimode fibres |
| IEC 60794-3-11:2010 | Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried, and lashed aerial single-mode optical fibre telecommunication cables |
| EN 50411-2-8:2009 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 2-8: Microduct connectors, for air blown optical fibres, Type 1 |
| EN 60794-1-20:2014 | Optical fibre cables - Part 1-20: Generic specification - Basic optical cable test procedures - General and definitions |
| IEC 60794-1-22:2017 RLV | Optical fibre cables - Part 1-22: Generic specification - Basic optical cable test procedures - Environmental test methods |
| EN 60794-3-40:2008 | Optical fibre cables - Part 3-40: Outdoor cables - Family specification for sewer cables and conduits for installation by blowing and/or pulling in non-man accessible storm and sanitary sewers |
| EN 50551-1:2011 | Simplex and duplex cables to be used for cords - Part 1: Blank Detail Specification and minimum requirements |
| EN 61290-1-2:2005 | Optical amplifiers - Test methods - Part 1-2: Power and gain parameters - Electrical spectrum analyzer method |
| EN 61746:2005 | Calibration of optical time-domain reflectometers (OTDR) |
| EN 60794-3-11:2010 | Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables |
| EN 60793-1-22:2002 | Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement |
| EN 187105:2002 | Single mode optical cable (duct/direct buried installation) |
| EN 50551-2:2013 | Simplex and duplex cables to be used for cords - Part 2: Detailed specification and minimum requirements for a 3,0 mm simplex ruggedised single mode fibre cable to be used for patchcords/cords category U |
| EN 60793-1-53:2014 | Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests |
| EN 60794-2-42:2008 | Optical fibre cables - Part 2-42: Indoor optical fibre cables - Product specification for simplex and duplex cables with A4 fibres |
| EN 60793-1-54:2013 | Optical fibres - Part 1-54: Measurement methods and test procedures - Gamma irradiation |
| EN 60794-5-10:2014 | Optical fibre cables - Part 5–10: Family specification - Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
| EN 60793-1-44:2011 | OPTICAL FIBRES - PART 1-44: MEASUREMENT METHODS AND TEST PROCEDURES - CUT-OFF WAVELENGTH |
| EN 60793-2-50:2016 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| EN 60793-1-50:2015 | Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests |
| EN 60794-4-20:2012 | OPTICAL FIBRE CABLES - PART 4-20: AERIAL OPTICAL CABLES ALONG ELECTRICAL POWER LINES - FAMILY SPECIFICATION FOR ADSS (ALL DIELECTRIC SELF SUPPORTED) OPTICAL CABLES (IEC 60794-4-20:2012) |
| IEC 60793-1-43:2015 | Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture measurement |
| IEC 60793-1-22:2001 | Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.