IEC 60364-4-443:1995+AMD1:1998 CSV
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electrical installations of buildings - Part 4: Protection for safety - Chapter 44: Protection against overvoltages - Section 443: Protection against overvoltages of atmospheric origin or due to switching
Amended by
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
01-08-2001
Superseded by
Language(s)
English - French
Published date
19-03-1999
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 General
1.1 Scope and object
1.2 Normative references
2 Classification of impulse withstand categories
(overvoltage categories)
2.1 Purpose of classification of impulse withstand
categories (overvoltage categories)
3 Arrangements for overvoltage control
3.1 Inherent control
3.2 Protective control
4 Selection of equipment in the installation
Annex A(informative) - Guidance for protective control
applied in the overhead lines according to note 1
Identifies and describes the locations in electrical installations where transient overvoltages may appear; describes the means by which such overvoltages may be limited to values not exceeding the withstand impulse voltages of the equipment supplied.
| Committee |
TC 64
|
| DevelopmentNote |
Previously entered as 3ED 99, this version is a Consolidated Edition which incorporates the 2ED 95 and Amendment 1 99.
|
| DocumentType |
Standard
|
| Pages |
15
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| HD 384.4.443 S1:2000 | Identical |
| NEN HD 384-4-443 : 2001 | Identical |
| SAC GB 16895.12 : 2001 | Identical |
| UNE 20460-4-443:2007 | Identical |
| DIN VDE 0100-443:2016-10 | Corresponds |
| NBN EN 2378 : 1995 | Identical |
| CEI 64-8/4 : 2012 | Identical |
| PN IEC 60364-4-443 : 1999 | Identical |
| SN HD 384.4.443 : 200S1 | Identical |
| VDE 0100-443:2016-10 | Identical |
| BS EN 61851-22:2002 | Electric vehicle conductive charging system A.C. electric vehicle charging station |
| S.R. HD 60364-5-534:2016 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-53: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - ISOLATION, SWITCHING AND CONTROL - CLAUSE 534: DEVICES FOR PROTECTION AGAINST TRANSIENT OVERVOLTAGES |
| 03/311404 DC : 0 | IEC 61010-1 ED.3 - SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 1: GENERAL REQUIREMENTS |
| NF EN 62020 : 1999 AMD 1 2005 | ELECTRICAL ACCESSORIES - RESIDUAL CURRENT MONITORS FOR HOUSEHOLD AND SIMILAR USES (RCMS) |
| IEC 61851-21:2001 | Electric vehicle conductive charging system - Part 21: Electric vehicle requirements for conductive connection to an a.c./d.c. supply |
| S.R. HD 60364-5-51:2009 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-51: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - COMMON RULES |
| NF EN 61851-21 : 2002 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21: ELECTRIC VEHICLE REQUIREMENTS FOR CONDUCTIVE CONNECTION TO AN A.C./D.C. SUPPLY |
| 01/219351 DC : DRAFT JAN 2001 | IEC 60364-5-53/A1 ED.2 - ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-53: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR |
| BS EN 61851-21:2002 | Electric vehicle conductive charging system Electric vehicle requirements for conductive connection to an a.c./d.c. supply |
| HD 60364-5-51:2009/A12:2017 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-51: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - COMMON RULES |
| EN 50539-11 : 2013 AMD 1 2014 | LOW-VOLTAGE SURGE PROTECTIVE DEVICES - SURGE PROTECTIVE DEVICES FOR SPECIFIC APPLICATION INCLUDING D.C. - PART 11: REQUIREMENTS AND TESTS FOR SPDS IN PHOTOVOLTAIC APPLICATIONS |
| HD 60364-5-534:2016 | Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control - Clause 534: Devices for protection against transient overvoltages |
| DIN VDE 0660-100 : 1992 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES |
| NF EN 61663-2 : 2001 | LIGHTNING PROTECTION - TELECOMMUNICATION LINES - PART 2: LINES USING METALLIC CONDUCTORS |
| CEI EN 61851-22 : 2003 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: AC ELECTRIC VEHICLE CHARGING STATION |
| CSA E60127.6 : 2003 | MINIATURE FUSES - PART 6: FUSE-HOLDERS FOR MINIATURE CARTRIDGE FUSE-LINKS |
| CAN/CSA-E60127-6-03 (R2017) | Miniature Fuses - Part 6: Fuse-Holders for Miniature Cartridge Fuse-Links (Adopted CEI/IEC 127-6:1994, first edition, 1994-04, including Amendment 1:1996, with Canadian deviations) | Coupe-circuit miniatures - Partie 6: Ensembles-porteurs pour cartouches de coupe-circuit miniatures (norme CEI/IEC 127-6:1994 adoptée, première édition, 1994-04, y compris l\'Amendement 1:1996, avec exigences propres au Canada) |
| IEC 60364-5-548:1996+AMD1:1998 CSV | Electrical installations of buildings - Part 5: Selection and erection of electrical equipment - Section 548: Earthing arrangements and equipotential bonding for information technology installations |
| IEC TR 61131-4:2004 | Programmable controllers - Part 4: User guidelines |
| I.S. EN 50539-11:2013 | LOW-VOLTAGE SURGE PROTECTIVE DEVICES - SURGE PROTECTIVE DEVICES FOR SPECIFIC APPLICATION INCLUDING D.C. - PART 11: REQUIREMENTS AND TESTS FOR SPDS IN PHOTOVOLTAIC APPLICATIONS |
| S.R. HD 60364-7-712:2016 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-712: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - PHOTOVOLTAIC (PV) SYSTEMS |
| NF EN 61851-22 : 2002 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: A.C. ELECTRIC VEHICLE CHARGING STATION |
| DIN V VDE V 0800-2-548 : 1999 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - SECTION 548: EARTHING ARRANGEMENTS AND EQUIPOTENTIAL BONDING FOR INFORMATION TECHNOLOGY INSTALLATIONS |
| VDE 0100-537 : 1999 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT; CHAPTER 53: SWITCH GEAR AND CONTROL GEAR; SECTION 537: DEVICES FOR ISOLATION AND SWITCHING |
| VDE 0220-3 : 1977 | SPECIFICATION FOR SINGLE AND MULTIPLE CABLE CLAMPS WITH INSULATING PARTS IN ELECTRICAL POWER CABLE INSTALLATIONS UP TO 1000 V |
| DIN VDE 0100-537 : 1999 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - CHAPTER 53: SWITCHGEAR AND CONTROL GEAR - SECTION 537: DEVICES FOR ISOLATION AND SWITCHING |
| EN 61851-21:2002 | Electric vehicle conductive charging system - Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply |
| 03/103069 DC : DRAFT JAN 2003 | |
| BS EN 61663-2:2001 | Lightning protection. Telecommunication lines Lines using metallic conductors |
| CSA E60127.6 : 2003 : R2012 | MINIATURE FUSES - PART 6: FUSE-HOLDERS FOR MINIATURE CARTRIDGE FUSE-LINKS |
| BIS IS 12640-2 : 2008 | RESIDUAL CURRENT OPERATED CIRCUIT-BREAKING FOR HOUSEHOLD AND SIMILAR USES - PART 2: CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION (RCBOS) |
| I.S. HD 384.1:2002 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 1: SCOPE, OBJECT AND FUNDAMENTAL PRINCIPLES |
| CEI EN 61663-2 : 2003 | LIGHTNING PROTECTION - TELECOMMUNICATION LINES - PART 2: LINES USING METALLIC CONDUCTORS |
| IEC 61024-1-2:1998 | Protection of structures against lightning - Part 1-2: General principles - Guide B - Design, installation, maintenance and inspection of lightning protection systems |
| IEC 61991:2000 | Railway applications - Rolling stock - Protective provisions against electrical hazards |
| EN 61663-2 : 2001 | LIGHTNING PROTECTION - TELECOMMUNICATION LINES - PART 2: LINES USING METALLIC CONDUCTORS |
| 12/30259014 DC : 0 | BS EN 60127-6 - MINIATURE FUSES - PART 6: FUSE-HOLDERS FOR MINIATURE FUSE-LINKS |
| IEC 61851-22:2001 | Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station |
| CEI UNI EN 12966-1 : 2010 | ROAD VERTICAL SIGNS - VARIABLE MESSAGE TRAFFIC SIGNS - PART 1: - PRODUCT STANDARD |
| 07/30168572 DC : 0 | BS IEC 61010-1 - SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 1: GENERAL REQUIREMENTS |
| HD 384.1 : 200S2 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 1: SCOPE, OBJECT AND FUNDAMENTAL PRINCIPLES |
| I.S. HD 60364-5-51:2009 | ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-51: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - COMMON RULES (IEC 60364-5-51:2005 (MOD)) |
| I.S. EN 62020:1999 | ELECTRICAL ACCESSORIES - RESIDUAL CURRENT MONITORS FOR HOUSEHOLD AND SIMILAR USES (RCMS) |
| I.S. EN 60439-1:2000 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| 17/30361391 DC : 0 | BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| 00/246907 DC : DRAFT DEC 2000 | BS EN 61980-1 - ELECTRICAL - ELECTRIC VEHICLE INDUCTIVE CHARGING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| 97/200935 DC : DRAFT JAN 1997 | IEC 60364 - ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - REVISION OF CHAPTER 54: EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS |
| IEC 61058-2-4:1995+AMD1:2003 CSV | Switches for appliances - Part 2-4: Particular requirements for independently mounted switches |
| BS EN 60439-1:1999 | Low-voltage switchgear and controlgear assemblies Type-tested and partially type-tested assemblies |
| 12/30266672 DC : 0 | BS EN 60598-1 ED 8.0 - LUMINAIRES - PART 1: GENERAL REQUIREMENTS AND TESTS |
| BS 7822-1:1995 | Insulation coordination for equipment within low-voltage systems Principles, requirements and tests |
| 98/203095 DC : DRAFT JULY 1998 | PRENV 50275-2-3 - CONDUCTIVE CHARGING FOR ELECTRIC VEHICLES - PART 2-3: D.C. CHARGING STATION |
| EN 61851-22:2002 | Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station |
| EN 62020:1998/A1:2005 | ELECTRICAL ACCESSORIES - RESIDUAL CURRENT MONITORS FOR HOUSEHOLD AND SIMILAR USES (RCMS) |
| IEC 60364-5-534:1997 | Electrical installations of buildings - Part 5: Selection and erection of electrical equipment - Section 534: Devices for protection against overvoltages |
| IEC 61663-2:2001 | Lightning protection - Telecommunication lines - Part 2: Lines using metallic conductors |
| BS 7822-3:1995 | Insulation coordination for equipment within low-voltage systems Use of coatings to achieve insulation coordination of printed board assemblies |
| BS EN 62020:1999 | Electrical accessories. Residual current monitors for household and similar uses (RCMs) |
| CEI UNI EN 12966-2/Ab:2020-02 | ROAD VERTICAL SIGNS - VARIABLE MESSAGE TRAFFIC SIGNS - PART 2: INITIAL TYPE TESTING |
| BIS IS 12640-1 : 2008 | RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS FOR HOUSEHOLD AND SIMILAR USES - PART 1: CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION (RCCBS) |
| CSA E1008.1 : 0 | RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBS) - PART 1: GENERAL RULES |
| IEC 62020:1998+AMD1:2003 CSV | Electrical accessories - Residual current monitors for household and similar uses (RCMs) |
| OVE/ONORM EN 62020 : AMD 1 2006 | ELECTRICAL ACCESSORIES - RESIDUAL CURRENT MONITORS FOR HOUSEHOLD AND SIMILAR USES (RCMS) |
| HD 60364-7-712:2016 | Low-voltage electrical installations - Part 7-712: Requirements for special installations or locations - Photovoltaic (PV) systems |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| DIN VDE 0110-1 : 1997 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS |
| IEC 61024-1:1990 | Protection of structures against lightning - Part 1: General principles |
| IEC 60050-826:2004 | International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.