I.S. EN ISO 286-1:2010/AC:2013
Current
The latest, up-to-date edition.
GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS (ISO 286-1:2010)
Hardcopy , PDF
English
01-01-2010
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 ISO code system for tolerances on linear sizes
5 ISO fit system
Annex A (informative) - Further information about the
ISO system of limits and fits and former practice
Annex B (informative) - Examples of the use of ISO 286-1
to determine fits and tolerance classes
Annex C (informative) - Relationship to the GPS matrix model
Bibliography
Specifies the ISO code system for tolerances to be used for linear sizes of features of the following types: a) cylinder; b) two parallel opposite surfaces.
| DevelopmentNote |
Supersedes I.S. EN 20286-1. (05/2010)
|
| DocumentType |
Standard
|
| Pages |
61
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| ISO 286-1:2010 | Identical |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO/TS 17450-2:2002 | Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 1:2016 | Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions |
| ISO/R 1938:1971 | ISO system of limits and fits Part II : Inspection of plain workpieces |
| ISO 3534-1:2006 | Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.