I.S. EN ISO 25762:2012
Current
The latest, up-to-date edition.
PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES (ISO 25762:2009)
Hardcopy , PDF
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Fibre reinforcement
5 Fire characteristics
6 Fire test methods
Annex A (informative) - Heat release measurements
on FRP composites
Annex B (informative) - Typical results given for
glass-fibre-reinforced polymer composites
by ISO and EN fire test methods
Annex C (informative) - Recommendations for the
handling and storage of fibre-reinforced
polymer composites
Annex D (informative) - Procedure in the event of
fire involving fibre-reinforced polymer
composites
Annex E (informative) - Mounting and fixing of
test specimens of fibre-reinforced polymer
composites
Bibliography
Provides guidelines for the assessment of the fire characteristics and fire performance of fibre-reinforced polymer (FRP) composites, particularly in structural applications in buildings and transport.
| DocumentType |
Standard
|
| Pages |
43
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| ISO 25762:2009 | Identical |
| EN ISO 25762:2012 | Identical |
| ISO 5660-1:2015 | Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 1: Heat release rate (cone calorimeter method) and smoke production rate (dynamic measurement) |
| ISO 1268-1:2001 | Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions |
| ISO 5658-2:2006 | Reaction to fire tests Spread of flame Part 2: Lateral spread on building and transport products in vertical configuration |
| ISO 13784-2:2002 | Reaction-to-fire tests for sandwich panel building systems Part 2: Test method for large rooms |
| ISO 10093:1998 | Plastics Fire tests Standard ignition sources |
| ISO 9705:1993 | Fire tests Full-scale room test for surface products |
| ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
| ISO 16312-1:2016 | Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment Part 1: Criteria |
| ISO 5659-2:2017 | Plastics — Smoke generation — Part 2: Determination of optical density by a single-chamber test |
| ISO 5660-2:2002 | Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 2: Smoke production rate (dynamic measurement) |
| ISO 1268-4:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 4: Moulding of prepregs |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| ISO 1268-7:2001 | Fibre-reinforced plastics Methods of producing test plates Part 7: Resin transfer moulding |
| ISO 13943:2017 | Fire safety — Vocabulary |
| ISO 24473:2008 | Fire tests — Open calorimetry — Measurement of the rate of production of heat and combustion products for fires of up to 40 MW |
| EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| ISO 13785-2:2002 | Reaction-to-fire tests for façades — Part 2: Large-scale test |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
| ISO/TS 5658-1:2006 | Reaction to fire tests — Spread of flame — Part 1: Guidance on flame spread |
| ISO 1268-6:2002 | Fibre-reinforced plastics — Methods of producing test plates — Part 6: Pultrusion moulding |
| ISO 1268-10:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens |
| ISO/TR 9705-2:2001 | Reaction-to-fire tests Full-scale room tests for surface products Part 2: Technical background and guidance |
| ISO 1268-8:2004 | Fibre-reinforced plastics — Methods of producing test plates — Part 8: Compression moulding of SMC and BMC |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 10840:2008 | Plastics — Guidance for the use of standard fire tests |
| ISO 1268-2:2001 | Fibre-reinforced plastics Methods of producing test plates Part 2: Contact and spray-up moulding |
| ISO 15791-1:2014 | Plastics — Development and use of intermediate-scale fire tests for plastics products — Part 1: General guidance |
| ISO/TR 5660-3:2003 | Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 3: Guidance on measurement |
| ISO 14696:2009 | Reaction-to-fire tests Determination of fire and thermal parameters of materials, products and assemblies using an intermediate-scale calorimeter (ICAL) |
| ISO 13571:2012 | Life-threatening components of fire — Guidelines for the estimation of time to compromised tenability in fires |
| ISO 19706:2011 | Guidelines for assessing the fire threat to people |
| ISO/TR 16312-2:2007 | Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment Part 2: Evaluation of individual physical fire models |
| CEN/TS 15447:2006 | Mounting and fixing in reaction to fire tests under the Construction Products Directive |
| ISO 13784-1:2014 | Reaction to fire test for sandwich panel building systems — Part 1: Small room test |
| ISO 9239-1:2010 | Reaction to fire tests for floorings Part 1: Determination of the burning behaviour using a radiant heat source |
| ISO 1268-5:2001 | Fibre-reinforced plastics Methods of producing test plates Part 5: Filament winding |
| ISO 21367:2007 | Plastics — Reaction to fire — Test method for flame spread and combustion product release from vertically oriented specimens |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| ISO 13927:2015 | Plastics — Simple heat release test using a conical radiant heater and a thermopile detector |
| ISO 14697:2007 | Reaction-to-fire tests — Guidance on the choice of substrates for building and transport products |
| ISO 1268-9:2003 | Fibre-reinforced plastics — Methods of producing test plates — Part 9: Moulding of GMT/STC |
| ISO 1268-3:2000 | Fibre-reinforced plastics Methods of producing test plates Part 3: Wet compression moulding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.