I.S. EN ISO 17078-3:2009
Current
The latest, up-to-date edition.
PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING AND PRODUCTION EQUIPMENT - PART 3: RUNNING TOOLS, PULLING TOOLS AND KICK-OVER TOOLS AND LATCHES FOR SIDE-POCKET MANDRELS
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Functional specification
5.1 General
5.2 Functional characteristics
5.3 Well parameters
5.4 Operational parameters
5.5 Environmental service grades (class designation)
5.6 Design validation grades
5.7 Product functional testing grades
5.8 Quality grades
5.9 Additional testing
6 Technical specification
6.1 General requirements
6.2 Technical requirements
6.3 Design criteria
6.4 Allowable design changes
6.5 Design verification and validation requirements
6.6 Product functional testing requirements
7 Supplier/manufacturer requirements
7.1 General
7.2 Documentation and data control
7.3 Product identification requirements
7.4 Quality control requirements
7.5 Heat treatment requirements
7.6 Welding requirements
7.7 Non-destructive examination (NDE) requirements
7.8 Storage and shipping preparation
7.9 Allowable changes after manufacturing
7.10 Reconditioning and repair of used running, pulling and
kick-over tools and latches
Annex A (normative) - Requirements for running and pulling tools
Annex B (normative) - Requirements for kick-over tools
Annex C (normative) - Requirements for latches
Annex D (normative) - Side-pocket mandrel tool interface evaluations
Annex E (informative) - Figures
Bibliography
Specifies requirements and guidelines for running tools, pulling tools, kick-over tools and latches used for the installation and retrieval of flow control and other devices to be installed in side-pocket mandrels for use in the petroleum and natural gas industries.
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| ISO 17078-3:2009 | Identical |
| EN ISO 17078-3:2009 | Identical |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 80000-4:2006 | Quantities and units Part 4: Mechanics |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ISO 31-0:1992 | Quantities and units Part 0: General principles |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 3601-1:2012 | Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| ISO 17078-2:2007 | Petroleum and natural gas industries — Drilling and production equipment — Part 2: Flow-control devices for side-pocket mandrels |
| SAE AMS H 6875 : 2010 | HEAT TREATMENT OF STEEL RAW MATERIALS |
| ISO 3601-3:2005 | Fluid power systems O-rings Part 3: Quality acceptance criteria |
| ISO 17078-1:2004 | Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels |
| ISO 18265:2013 | Metallic materials — Conversion of hardness values |
| ISO/IEC Guide 22:1996 | General criteria for supplier's declaration of conformity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.