I.S. EN ISO 16961:2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - INTERNAL COATING AND LINING OF STEEL STORAGE TANKS (ISO 16961:2015)
Available format(s)
Hardcopy , PDF
Superseded date
30-05-2024
Superseded by
Language(s)
English
Published date
01-01-2015
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
Foreword
Introduction
1 Scope
2 Conformance
3 Normative references
4 Terms, definitions and abbreviated terms
5 Pre-work requirements
6 Coating/lining materials
7 Surface preparation
8 Coating/lining application
9 Inspection and testing
10 Quality requirements
11 Documentation
Annex A (informative) - Dew point calculation chart
Annex B (informative) - Caulking (putty) application
Annex C (informative) - Example of coating/lining work
record/data sheet
Annex D (informative) - Example of coating/lining
inspection and testing data sheet
Bibliography
Defines the minimum requirements for surface preparation, materials, application, inspection and testing of internal coating lining systems that are intended to be applied on internal surfaces of steel storage tanks of crude oil, hydrocarbons and water for corrosion protection.
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 16961:2015 | Identical |
| EN ISO 16961:2015 | Identical |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 19840:2012 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces |
| ASTM D 870 : 2015 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ISO 8502-3:2017 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO/TS 29001:2010 | Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations |
| ASTM D 512 : 2012 | Standard Test Methods for Chloride Ion In Water (Withdrawn 2021) |
| NACE SP 01 88 : 2006 | DISCONTINUITY (HOLIDAY) TESTING OF NEW PROTECTIVE COATINGS ON CONDUCTIVE SUBSTRATES |
| NACE SP 01 78 : 2007 | DESIGN, FABRICATION, AND SURFACE FINISH PRACTICES FOR TANKS AND VESSELS TO BE LINED FOR IMMERSION SERVICE |
| CFR 29(PTS1900-1910) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| SSPC-SP 11 : 2012 | POWER-TOOL CLEANING TO BARE METAL |
| ASTM D 4541 : 2017 : REDLINE | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 4417 : 2014 : REDLINE | Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel |
| ASTM F 21 : 2014 : REDLINE | Standard Test Method for Hydrophobic Surface Films by the Atomizer Test |
| API 653 : 2014 | TANK INSPECTION, REPAIR, ALTERATION, AND RECONSTRUCTION |
| NACE 6G186 : 0 | SURFACE PREPARATION OF SOLUBLE SALT CONTAMINATED STEEL SUBSTRATES PRIOR TO COATING |
| ISO 8502-10:1999 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 10: Field method for the titrimetric determination of water-soluble chloride |
| ASTM D 4285 : 1983 : R2018 | Standard Test Method for Indicating Oil or Water in Compressed Air |
| NACE 11 : 2003 | THIN-FILM ORGANIC LININGS APPLIED IN NEW CARBON STEEL PROCESS VESSELS |
| ISO 8501-3:2006 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 3: Preparation grades of welds, edges and other areas with surface imperfections |
| SSPC-QP 1 : 2012 | STANDARD PROCEDURE FOR EVALUATING THE QUALIFICATIONS OF IINDUSTRIAL/MARINE PAINTING CONTRACTORS (FIELD APPLICATION TO COMPLEX INDUSTRIAL AND MARINE STEEL STRUCTURES) |
| NACE 6A192 : 2000 | DEHUMIDIFICATION AND TEMPERATURE CONTROL DURING SURFACE PREPARATION, APPLICATION, AND CURING FOR COATINGS/LININGS OF STEEL TANKS, VESSELS, AND OTHER ENCLOSED SPACES |
| ASTM D 4414 : 1995 | Standard Practice for Measurement of Wet Film Thickness by Notch Gages |
| SSPC-PA 6 : 2002 | FIBERGLASS-REINFORCED PLASTIC (FRP) LININGS APPLIED TO BOTTOMS OF CARBON STEEL ABOVEGROUND STORAGE TANKS |
| ASTM D 610 : 2008 | Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces |
| NACE TM 01 74 : 2002 | LABORATORY METHODS FOR THE EVALUATION OF PROTECTIVE COATINGS AND LINING MATERIALS ON METALLIC SUBSTRATES IN IMMERSION SERVICE |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| SSPC-GUIDE 15 : 2013 | FIELD METHODS FOR EXTRACTION AND ANALYSIS OF SOLUBLE SALTS ON STEEL AND OTHER NONPOROUS SUBSTRATES |
| API 2217A : 2009 | SAFE WORK IN INERT CONFINED SPACES IN THE PETROLEUM AND PETROCHEMICAL INDUSTRIES |
| ISO 11127-7:2011 | Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 7: Determination of water-soluble chlorides |
| ISO 9004:2009 | Managing for the sustained success of an organization A quality management approach |
| SSPC-AB 1 : 2015 | MINERAL AND SLAG ABRASIVES |
| NACE 10 : 2002 | FIBERGLASS-REINFORCED PLASTIC (FRP) LININGS APPLIED TO BOTTOMS OF CARBON STEEL ABOVEGROUND STORAGE TANKS |
| ISO 29601:2011 | Paints and varnishes Corrosion protection by protective paint systems Assessment of porosity in a dry film |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 3673-1:1996 | Plastics Epoxy resins Part 1: Designation |
| ASTM G 42 : 2011 : REDLINE | TEST METHOD FOR CATHODIC DISBONDING OF PIPELINE COATINGS SUBJECTED TO ELEVATED TEMPERATURES |
| API 2015 : 2014 | REQUIREMENTS FOR SAFE ENTRY AND CLEANING OF PETROLEUM STORAGE TANKS |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
| SSPC-AB 2 : 2015 | CLEANLINESS OF RECYCLED FERROUS METALLIC ABRASIVES |
| ISO 12944-3:2017 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations |
| ASTM D 5420 : 2016 : REDLINE | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 8502-6:2006 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 6: Extraction of soluble contaminants for analysis The Bresle method |
| ISO 8502-9:1998 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 9: Field method for the conductometric determination of water-soluble salts |
| SSPC-PA 8 : 2003 | THIN-FILM ORGANIC LININGS APPLIED IN NEW CARBON STEEL PROCESS VESSELS |
| API 650 : 2013 | WELDED TANKS FOR OIL STORAGE |
| SSPC-SP 5 : 2015 | WHITE METAL BLAST CLEANING |
| ISO 8504-2:2000 | Preparation of steel substrates before application of paints and related products Surface preparation methods Part 2: Abrasive blast-cleaning |
| SSPC-TR 3 : 2000 | DEHUMIDIFICATION AND TEMPERATURE CONTROL DURING SURFACE PREPARATION, APPLICATION, AND CURING FOR COATINGS/LININGS OF STEEL TANKS, VESSELS, AND OTHER ENCLOSED SPACES |
| ISO 8502-11:2006 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 11: Field method for the turbidimetric determination of water-soluble sulfate |
| ISO Guide 31:2015 | Reference materials — Contents of certificates, labels and accompanying documentation |
| ASTM D 522 : 1993 : REV A | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| NACE RP 02 87 : 2002 | FIELD MEASUREMENT OF SURFACE PROFILE OF ABRASIVE BLAST-CLEANED STEEL SURFACES USING A REPLICA TAPE |
| ASTM D 3359 : 2017 : REDLINE | Standard Test Methods for Rating Adhesion by Tape Test |
| SSPC-GUIDE 12 : 2016 | GUIDE TO ILLUMINATION OF INDUSTRIAL COATING PROJECTS |
| ISO 8504-3:1993 | Preparation of steel substrates before application of paints and related products Surface preparation methods Part 3: Hand- and power-tool cleaning |
| ISO 4628-2:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering |
| API 652 : 2014 | LININGS OF ABOVEGROUND PETROLEUM STORAGE TANK BOTTOMS |
| ISO 7027:1999 | Water quality Determination of turbidity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.