I.S. EN ISO 12215-9:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 9: SAILING CRAFT APPENDAGES (ISO 12215-9:2012)
Hardcopy , PDF
05-11-2018
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Design stresses
6 Structural components to be assessed
7 Load cases
8 Computational methods
9 Compliance
Annex A (normative) - Application declaration
Annex B (informative) - Information on metal for appendages
and fasteners and "established practice" for
fastening and welding
Annex C (informative) - "Established practice" structural
arrangement for ballast keels
Annex D (informative) - "Established practice" calculation
of keel fin strength (fixed or canting) and fixed
ballast keel connected by bolts
Annex E (informative) - Geometrical properties of some typical
appendage foil shapes
Annex F (informative) - Simplified fatigue strength assessment
Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 94/25/EC as amended by Directive 2003/44/EC
Describes the loads and specifies the scantlings of sailing craft appendages on monohull sailing craft with a length of hull, L[H], of up to 24 m, measured according to ISO 8666.
| Committee |
TC 188
|
| DocumentType |
Standard
|
| Pages |
91
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 12215-9:2012 | Identical |
| ISO 12215-9:2012 | Identical |
| ISO 12215-5:2008 | Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 16143-2:2014 | Stainless steels for general purposes — Part 2: Corrosion-resistant semi-finished products, bars, rods and sections |
| GL I-1-1 : JAN 2016 | RULES FOR CLASSIFICATION AND CONSTRUCTION - 1: SHIP TECHNOLOGY - PART 1: SEAGOING SHIPS - CHAPTER 1: HULL STRUCTURES |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 12217-2:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 2: Sailing boats of hull length greater than or equal to 6 m |
| ISO 8666:2016 | Small craft Principal data |
| NFE 25 030-1 : 2014 | FASTENERS - THREADED CONNECTIONS WITH ISO METRIC THREAD - PART 1: DESIGN RULES FOR TENSILE LOADED BOLTED JOINTS - SIMPLIFIED PROCEDURE - FIXATIONS |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| ISO 12215-6:2008 | Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| ABS 0037 : 1994 COR 2012 | GUIDE FOR BUILDING AND CLASSING OFFSHORE RACING YACHTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.