I.S. EN ISO 11607-1:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - PART 1: REQUIREMENTS FOR MATERIALS, STERILE BARRIER SYSTEMS AND PACKAGING SYSTEMS (ISO 11607-1:2006, INCLUDING AMD 1:2014)
Hardcopy , PDF
23-01-2020
06-08-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 Materials and preformed sterile barrier systems
6 Design and development requirements for packaging
systems
7 Information to be provided
Annex A (informative) - Guidance on medical packaging
Annex B (informative) - Standardized test methods and
procedures that may be used to demonstrate
compliance with the requirements of this part of
ISO 11607
Annex C (normative) - Test method for resistance of
impermeable materials to the passage of air
Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the essential requirements of
Directive 93/42/EEC [OJ L 169] aimed to be
covered
Annex ZB (informative) - Relationship between this European
Standard and the essential requirements of
Directive 90/385/EEC [OJ L 189] aimed to be
covered
Annex ZC (informative) - Relationship between this European
Standard and the essential requirements of
Directive 98/79/EC [OJ L 331] aimed to be
covered
Defines the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.
| Committee |
TC 198
|
| DevelopmentNote |
Supersedes I.S. EN 868-1. (07/2006)
|
| DocumentType |
Test Method
|
| Pages |
48
|
| ProductNote |
The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 11607-1:2006 | Identical |
| EN ISO 11607-1:2017 | Identical |
| NS EN ISO 11607-1 : 2017 | Identical |
| NBN EN ISO 11607-1 : 2009 + A1 2014 | Identical |
| UNE-EN ISO 11607-1:2017 | Identical |
| DIN EN ISO 11607-1:2014-11 | Identical |
| UNI EN ISO 11607-1 : 2014 | Identical |
| BS EN ISO 11607-1 : 2009 | Identical |
| EN 13795-1:2002+A1:2009 | Surgical drapes, gowns and clean air suits, used as medical devices, for patients, clinical staff and equipment - Part 1: General requirements for manufacturers, processors and products |
| ISO 11137-1:2006 | Sterilization of health care products Radiation Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| EN 550 : 1994 | STERILIZATION OF MEDICAL DEVICES - VALIDATION AND ROUTINE CONTROL OF ETHYLENE OXIDE STERILIZATION |
| ISO 11607-2:2006 | Packaging for terminally sterilized medical devices Part 2: Validation requirements for forming, sealing and assembly processes |
| ISO 11135:2014 | Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices |
| EN 285:2015 | Sterilization - Steam sterilizers - Large sterilizers |
| EN 868-5:2009 | Packaging for terminally sterilized medical devices - Part 5: Sealable pouches and reels of porous materials and plastic film construction - Requirements and test methods |
| EN 868-4:2017 | Packaging for terminally sterilized medical devices - Part 4: Paper bags - Requirements and test methods |
| ISO 13485:2016 | Medical devices Quality management systems Requirements for regulatory purposes |
| EN 868-1 : 1997 | PACKAGING MATERIALS AND SYSTEMS FOR MEDICAL DEVICES WHICH ARE TO BE STERILIZED - GENERAL REQUIREMENTS AND TEST METHODS |
| ISO 14937:2009 | Sterilization of health care products General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| EN 868-6:2017 | Packaging for terminally sterilized medical devices - Part 6: Paper for low temperature sterilization processes - Requirements and test methods |
| ISO 5636-1:1984 | Paper and board Determination of air permeance (medium range) Part 1: General method |
| EN 14180:2014 | Sterilizers for medical purposes - Low temperature steam and formaldehyde sterilizers - Requirements and testing |
| EN 868-2:2017 | Packaging for terminally sterilized medical devices - Part 2: Sterilization wrap - Requirements and test methods |
| EN 868-3:2017 | Packaging for terminally sterilized medical devices - Part 3: Paper for use in the manufacture of paper bags (specified in EN 868-4) and in the manufacture of pouches and reels (specified in EN 868-5) - Requirements and test methods |
| AAMI ST65:2008(R2018) | PROCESSING OF REUSABLE SURGICAL TEXTILES FOR USE IN HEALTH CARE FACILITIES |
| ISO 5636-2:1984 | Paper and board — Determination of air permeance (medium range) — Part 2: Schopper method |
| ISO 5636-5:2013 | Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method |
| EN 552:1994/A2:2000 | STERILIZATION OF MEDICAL DEVICES - VALIDATION AND ROUTINE CONTROL OF STERILIZATION BY IRRADIATION |
| ISO 186:2002 | Paper and board — Sampling to determine average quality |
| ISO/TS 11139:2006 | Sterilization of health care products Vocabulary |
| ISO 11137-3:2017 | Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control |
| ISO 11137-2:2013 | Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose |
| ISO 10993-1:2009 | Biological evaluation of medical devices Part 1: Evaluation and testing within a risk management process |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 868-7:2017 | Packaging for terminally sterilized medical devices - Part 7: Adhesive coated paper for low temperature sterilization processes - Requirements and test methods |
| ISO 13683:1997 | Sterilization of health care products Requirements for validation and routine control of moist heat sterilization in health care facilities |
| EN 1422:2014 | Sterilizers for medical purposes - Ethylene oxide sterilizers - Requirements and test methods |
| EN 554 : 1994 | STERILIZATION OF MEDICAL DEVICES - VALIDATION AND ROUTINE CONTROL OF STERILIZATION BY MOIST HEAT |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.