I.S. EN ISO 11120:2015
Current
The latest, up-to-date edition.
GAS CYLINDERS - REFILLABLE SEAMLESS STEEL TUBES OF WATER CAPACITY BETWEEN 150 L AND 3000 L - DESIGN, CONSTRUCTION AND TESTING (ISO 11120:2015)
Hardcopy , PDF
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Inspection and testing
6 Materials
7 Design
8 Construction and workmanship
9 Type approval procedure
10 Batch tests
11 Tests on every tube
12 Special requirements for tubes for embrittling gases
13 Inspection certificate
14 Marking
Annex A (informative) - Typical chemistry groupings for
seamless steel tubes
Annex B (normative) - Ultrasonic examination
Annex C (informative) - Description and evaluation of
manufacturing imperfections and conditions for
rejection of seamless steel tubes at time of
final inspection by the manufacturer
Annex D (informative) - Acceptance certificate
Annex E (informative) - Type approval certificate
Annex F (informative) - Bend stress calculation
Bibliography
Describes minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests at manufacture of refillable quenched and tempered seamless steel tubes of water capacities from 150 l up to and including 3000 l for compressed and liquefied gases exposed to extreme world-wide ambient temperatures normally between -50 degrees C and +65 degrees C.
| DocumentType |
Standard
|
| Pages |
48
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 11120:2015-05 | Identical |
| UNI EN ISO 11120 : 2013 | Identical |
| NS EN ISO 11120 : 2015 | Identical |
| EN ISO 11120:2015 | Identical |
| NBN EN ISO 11120 : 2015 | Identical |
| UNE-EN ISO 11120:2015 | Identical |
| NF EN ISO 11120 : 2015 | Identical |
| SN EN ISO 11120 : 2015 | Identical |
| NEN EN ISO 11120 : 2015 | Identical |
| ISO 11120:2015 | Identical |
| BS EN ISO 11120:2015 | Identical |
| ISO 6506-3:2014 | Metallic materials Brinell hardness test Part 3: Calibration of reference blocks |
| ISO 10893-5:2011 | Non-destructive testing of steel tubes Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| ISO 148-2:2016 | Metallic materials — Charpy pendulum impact test — Part 2: Verification of testing machines |
| ISO 10893-8:2011 | Non-destructive testing of steel tubes Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| ISO 21028-2:2004 | Cryogenic vessels Toughness requirements for materials at cryogenic temperature Part 2: Temperatures between -80 degrees C and -20 degrees C |
| ISO 148-3:2016 | Metallic materials — Charpy pendulum impact test — Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines |
| ISO 11114-4:2017 | Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 4: Test methods for selecting steels resistant to hydrogen embrittlement |
| ISO 6506-2:2017 | Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines |
| ISO 6406:2005 | Gas cylinders Seamless steel gas cylinders Periodic inspection and testing |
| ISO 10893-2:2011 | Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| ISO 10893-4:2011 | Non-destructive testing of steel tubes Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections |
| ISO 11117:2008 | Gas cylinders Valve protection caps and valve guards Design, construction and tests |
| ISO 13769:2007 | Gas cylinders Stamp marking |
| ISO 11439:2013 | Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.