I.S. EN IEC 61281-1:2018
Current
Current
The latest, up-to-date edition.
FIBRE OPTIC COMMUNICATION SUBSYSTEMS - PART 1: GENERIC SPECIFICATION
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
10-04-2018
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and acronyms
5 Subsystem characteristics
Bibliography
Describes for fibre optic communication subsystems (FOCSs).
| DevelopmentNote |
Supersedes I.S. EN 61281-1. For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (04/2018)
|
| DocumentType |
Standard
|
| Pages |
0
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN IEC 61281-1:2018 | Identical |
| IEC 61281-1:1999 | Identical |
| IEC TR 61282-12:2016 | Fibre optic communication system design guides - Part 12: In-band optical signal-to-noise ratio (OSNR) |
| IEC 61290-3-2:2008 | Optical amplifiers - Test methods - Part 3-2: Noise figure parameters - Electrical spectrum analyzer method |
| IEC TR 61282-5:2002 | Fibre optic communication system design guides - Part 5: Accommodation and compensation of dispersion |
| IEC 61290-10-4:2007 | Optical amplifiers - Test methods - Part 10-4: Multichannel parameters - Interpolated source subtraction method using an optical spectrum analyzer |
| IEC 61280-2-11:2006 | Fibre optic communication subsystem test procedures - Part 2-11: Digital systems - Averaged Q-factor determination using amplitude histogram evaluation for optical signal quality monitoring |
| IEC 61280-2-10:2005 | Fibre optic communication subsystem test procedures - Part 2-10: Digital systems - Time-resolved chirp and alpha-factor measurement of laser transmitters |
| IEC 61274-1:2011 | Fibre optic interconnecting devices and passive components - Adaptors for fibre optic connectors - Part 1: Generic specification |
| IEC 60050-731:1991 | International Electrotechnical Vocabulary (IEV) - Part 731: Optical fibre communication |
| IEC 61280-1-3:2010 | Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Central wavelength and spectral width measurement |
| IEC 61290-10-5:2014 | Optical amplifiers - Test methods - Part 10-5: Multichannel parameters - Distributed Raman amplifier gain and noise figure |
| IEC 60793-2-10:2017 | Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres |
| IEC 60793-1-41:2010 | Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth |
| IEC 61290-3-3:2013 | Optical amplifiers - Test methods - Part 3-3: Noise figure parameters - Signal power to total ASE power ratio |
| IEC 61290-4-2:2011 | Optical amplifiers - Test methods - Part 4-2: Gain transient parameters - Broadband source method |
| IEC 61290-11-1:2008 | Optical amplifiers - Test methods - Part 11-1: Polarization mode dispersion parameter - Jones matrix eigenanalysis (JME) |
| IEC TR 61282-6:2003 | Fibre optic communication system design guides - Part 6: Skew design in parallel optical interconnection systems |
| IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
| IEC 61291-2:2016 | Optical amplifiers - Part 2: Single channel applications - Performance specification template |
| IEC 61290-1-3:2015 | Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC 61280-2-9:2009 | Fibre optic communication subsystem test procedures - Part 2-9: Digital systems - Optical signal-to-noise ratio measurement for dense wavelength-division multiplexed systems |
| IEC 60869-1:2012 | Fibre optic interconnecting devices and passive components - Fibre optic passive power control devices - Part 1: Generic specification |
| IEC 61290-6-1:1998 | Optical fibre amplifiers - Basic specification - Part 6-1: Test methods for pump leakage parameters - Optical demultiplexer |
| IEC 61290-1-1:2015 | Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method |
| IEC 60794-1-1:2015 | Optical fibre cables - Part 1-1: Generic specification - General |
| IEC 61291-4:2011 | Optical amplifiers - Part 4: Multichannel applications - Performance specification template |
| IEC TR 61282-15:2017 | Fibre optic communication system design guides - Part 15: Cable plant and link - Testing multi-fibre optic cable plant terminated with MPO connectors |
| IEC TR 61282-3:2006 | Fibre optic communication system design guides - Part 3: Calculation of link polarization mode dispersion |
| IEC 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable |
| IEC 61280-2-3:2009 | Fibre optic communication subsystem tets procedures - Part 2-3: Digital systems - Jitter and wander measurements |
| IEC 61280-2-12:2014 | Fibre optic communication subsystem test procedures - Part 2-12: Digital systems - Measuring eye diagrams and Q-factor using a software triggering technique for transmission signal quality assessment |
| IEC 61290-5-3:2002 | Basic specification for optical amplifier test methods - Part 5-3: Test methods for reflectance parameters - Reflectance tolerance test method using electrical spectrum analyzer |
| IEC 61290-5-2:2003 | Optical amplifiers - Test methods - Part 5-2: Reflectance parameters - Electrical spectrum analyser method |
| IEC 61290-7-1:2007 | Optical amplifiers - Test methods - Part 7-1: Out-of-band insertion losses - Filtered optical power meter method |
| IEC TR 61931:1998 | Fibre optic - Terminology |
| IEC 60874-1:2011 | Fibre optic interconnecting devices and passive components - Connectors for optical fibres and cables - Part 1: Generic specification |
| IEC 61280-4-1:2009 | Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement |
| IEC 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| IEC 61280-2-2:2012 | Fibre optic communication subsystem test procedures - Part 2-2: Digital systems - Optical eye pattern, waveform and extinction ratio measurement |
| IEC 61703:2016 | Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
| IEC 61290-3-1:2003 | Optical amplifiers - Test methods - Part 3-1: Noise figure parameters - Optical spectrum analyzer method |
| IEC TR 61282-7:2003 | Fibre optic communication system design guides - Part 7: Statistical calculation of chromatic dispersion |
| IEC 61290-10-2:2007 | Optical amplifiers - Test methods - Part 10-2: Multichannel parameters - Pulse method using a gated optical spectrum analyzer |
| IEC 61280-2-8:2003 | Fibre optic communication subsystem test procedures - Digital systems - Part 2-8: Determination of low BER using Q-factor measurements |
| IEC 61073-1:2009 | Fibre optic interconnecting devices and passive components - Mechanical splices and fusion splice protectors for optical fibres and cables - Part 1: Generic specification |
| IEC 61290-1:2014 | Optical amplifiers - Test methods - Part 1: Power and gain parameters |
| IEC 61291-1:2012 | Optical amplifiers - Part 1: Generic specification |
| IEC TR 61282-4:2013 | Fibre optic communication system design guides - Part 4: Accommodation and utilization of non-linear effects |
| IEC 60793-2-50:2015 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| IEC 61280-4-4:2017 | Fibre optic communication subsystem test procedures - Part 4-4: Cable plants and links - Polarization mode dispersion measurement for installed links |
| IEC 61290-4-1:2016 | Optical amplifiers - Test methods - Part 4-1: Gain transient parameters - Two-wavelength method |
| IEC 61290-11-2:2005 | Optical amplifiers - Test methods - Part 11-2: Polarization mode dispersion parameter - Poincaré sphere analysis method |
| IEC 61290-5-1:2006 | Optical amplifiers - Test methods - Part 5-1: Reflectance parameters - Optical spectrum analyzer method |
| IEC 61280-2-1:2010 | Fibre optic communication subsystem test procedures - Part 2-1: Digital systems - Receiver sensitivity and overload measurement |
| IEC 62614:2010 | Fibre optics - Launch condition requirements for measuring multimode attenuation |
| IEC 62149-1:2011 | Fibre optic active components and devices - Performance standards - Part 1: General and guidance |
| IEC 61290-1-2:2005 | Optical amplifiers - Test methods - Part 1-2: Power and gain parameters - Electrical spectrum analyzer method |
| IEC 61290-10-1:2009 | Optical amplifiers - Test methods - Part 10-1: Multichannel parameters - Pulse method using an optical switch and optical spectrum analyzer |
| IEC TS 62538:2008 | Categorization of optical devices |
| IEC 60875-1:2015 | Fibre optic interconnecting devices and passive components - Non-wavelength-selective fibre optic branching devices - Part 1: Generic specification |
| IEC TR 61282-8:2006 | Fibre optic communication system design guides - Part 8: Calculating dispersion penalty from measured time-resolved chirp data |
| IEC TR 61282-9:2016 | Fibre optic communication system design guides - Part 9: Guidance on polarization mode dispersion measurements and theory |
| IEC 61290-10-3:2002 | Optical amplifiers - Test methods - Part 10-3: Multichannel parameters - Probe methods |
| IEC 61280-1-4:2009 | Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method |
| IEC 60876-1:2014 | Fibre optic interconnecting devices and passive components - Fibre optic spatial switches - Part 1: Generic specification |
| IEC TR 61282-13:2014 | Fibre optic communication system design guides - Part 13: Guidance on in-service PMD and CD characterization of fibre optic links |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.