I.S. EN 81-43:2009
Current
The latest, up-to-date edition.
SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: LIFTS FOR CRANES
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
5.1 General
5.2 Load combinations and calculations
5.3 Base frame
5.4 Mast, ties and buffers
5.5 Liftway protection and landing access
5.6 Car
5.7 Drive unit
5.8 Electric installations and appliances
5.9 Control and limiting devices
5.10 Breakdown conditions
6 Verification
6.1 Verification of design
6.2 Special verification tests
6.3 Verification tests on each lift before first use
7 User information
7.1 Instruction handbook
7.2 Markings
7.3 Marking of control elements
Annex A (normative) - European stormwind map
Annex B (normative) - Electric safety devices
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Describes the safety requirements for the construction and installation of power operated lifts attached to cranes and intended for access to workplaces on cranes, by authorized persons.
| DocumentType |
Standard
|
| Pages |
63
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 81-43:2009 | Identical |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
| EN 14502-2:2005+A1:2008 | Cranes - Equipment for the lifting of persons - Part 2: Elevating control stations |
| EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength |
| IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN 12158-1:2000+A1:2010 | Builders' hoists for goods - Part 1: Hoists with accessible platforms |
| EN 13586:2004+A1:2008 | Cranes - Access |
| EN 81-1:1998+A3:2009 | Safety rules for the construction and installation of lifts - Part 1: Electric lifts |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN 12158-2:2000+A1:2010 | Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
| ISO 4309:2010 | Cranes Wire ropes Care and maintenance, inspection and discard |
| EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| EN 12159:2012 | Builders hoists for persons and materials with vertically guided cages |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN 1808:2015 | Safety requirements for suspended access equipment - Design calculations, stability criteria, construction - Examinations and tests |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 13015:2001+A1:2008 | Maintenance for lifts and escalators - Rules for maintenance instructions |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.